Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: This paper presents the gain improvement of a sector antenna for mobile phone base station by using the new technique to enhance its gain for microstrip antenna (MSA) array without construction enlargement. The curved woodpile Electromagnetic Band Gap (EBG) has been utilized to improve the gain instead. The advantages of this proposed antenna are reducing the length of MSAs array but providing the higher gain and easy fabrication and installation. Moreover, it provides a fan-shaped radiation pattern, wide in the horizontal direction and relatively narrow in the vertical direction, which appropriate for mobile phone base station. The paper also presents the design procedures of a 1x8 MSAs array associated with U-shaped reflector for decreasing their back and side lobes. The fabricated curved woodpile EBG exhibits bandgap characteristics at 2.1 GHz and is utilized for realizing a resonant cavity of MSAs array. This idea has been verified by both the Computer Simulation Technology (CST) software and experimental results. As the results, the fabricated proposed antenna achieves a high gain of 20.3 dB and the half-power beam widths in the E- and H-plane of 36.8 and 8.7 degrees, respectively. Good qualitative agreement between measured and simulated results of the proposed antenna was obtained.
Abstract: Seismic design criteria based on performance of
structures have recently been adopted by practicing engineers in
response to destructive earthquakes. A simple but efficient
structural-analysis tool capable of predicting both the strength and
ductility is needed to analyze reinforced concrete (RC) structures
under such event. A three-dimensional lattice model is developed in
this study to analyze torsions in high-strength RC members.
Optimization techniques for determining optimal variables in each
lattice model are introduced. Pure torsion tests of RC members are
performed to validate the proposed model. Correlation studies
between the numerical and experimental results confirm that the
proposed model is well capable of representing salient features of the
experimental results.
Abstract: Building code-related literature provides
recommendations on normalizing approaches to the calculation of
the dynamic properties of structures. Most building codes make a
distinction among types of structural systems, construction material,
and configuration through a numerical coefficient in the
expression for the fundamental period. The period is then used in
normalized response spectra to compute base shear. The typical
parameter used in simplified code formulas for the fundamental
period is overall building height raised to a power determined from
analytical and experimental results. However, reinforced concrete
buildings which constitute the majority of built space in less
developed countries pose additional challenges to the ones built with
homogeneous material such as steel, or with concrete under stricter
quality control. In the present paper, the particularities of reinforced
concrete buildings are explored and related to current methods of
equivalent static analysis. A comparative study is presented between
the Uniform Building Code, commonly used for buildings within
and outside the USA, and data from the Middle East used to model
151 reinforced concrete buildings of varying number of bays, number
of floors, overall building height, and individual story height. The
fundamental period was calculated using eigenvalue matrix
computation. The results were also used in a separate regression
analysis where the computed period serves as dependent variable,
while five building properties serve as independent variables. The
statistical analysis shed light on important parameters that simplified
code formulas need to account for including individual story height,
overall building height, floor plan, number of bays, and concrete
properties. Such inclusions are important for reinforced concrete
buildings of special conditions due to the level of concrete damage,
aging, or materials quality control during construction.
Overall results of the present analysis show that simplified code
formulas for fundamental period and base shear may be applied but
they require revisions to account for multiple parameters. The
conclusion above is confirmed by the analytical model where
fundamental periods were computed using numerical techniques and
eigenvalue solutions. This recommendation is particularly relevant
to code upgrades in less developed countries where it is customary to
adopt, and mildly adapt international codes.
We also note the necessity of further research using empirical data
from buildings in Lebanon that were subjected to severe damage due
to impulse loading or accelerated aging. However, we excluded this
study from the present paper and left it for future research as it has its
own peculiarities and requires a different type of analysis.
Abstract: The effect of an abruptly expanding channel on the main characteristics of hydraulic jump is considered experimentally. The present study was made for supercritical flow of Froude number varying between 2 to 9 and approach to expanded channel width ratios 0.4, 0.5, 0.6 and 0.8. Physical explanations of the variation of these characteristics under varying flow conditions are discussed based on the observation drawn from experimental results. The analytical equation for the sequent depth ratio in an abruptly expanding channel as given by eminent hydraulic engineers are verified well with the experimental data for all expansion ratios, and the empirical relation was also verified with the present experimental data.
Abstract: Conical sections and shells made from metal plates are widely used in various industrial applications. 3-roller conical bending process is preferably used to produce such conical sections and shells. Bending mechanics involved in the process is complex and little work is done in this area. In the present paper an analytical model is developed to predict bending force which will be acting during 3-roller conical bending process. To verify the developed model, conical bending experiments are performed. Analytical results and experimental results were compared. Force predicted by analytical model is in close proximity of the experimental results. The error in the prediction is ±10%. Hence the model gives quite satisfactory results. Present model is also compared with the previously published bending force prediction model and it is found that the present model gives better results. The developed model can be used to estimate the bending force during 3-roller bending process and can be useful to the designers for designing the 3-roller conical bending machine.
Abstract: The data transmission between mobile hosts and base stations (BSs) in Mobile networks are often vulnerable to failure. So, efficient link connectivity, in terms of the services of both base stations and communication channels of the network, is required in wireless mobile networks to achieve highly reliable data transmission. In addition, it is observed that the number of blocked hosts is increased due to insufficient number of channels during heavy load in the network. Under such scenario, the channels are allocated accordingly to offer a reliable communication at any given time. Therefore, a reliability-based channel allocation model with acceptable system performance is proposed as a MOO problem in this paper. Two conflicting parameters known as Resource Reuse factor (RRF) and the number of blocked calls are optimized under reliability constraint in this problem. The solution to such MOO problem is obtained through NSGA-II (Non dominated Sorting Genetic Algorithm). The effectiveness of the proposed model in this work is shown with a set of experimental results.
Abstract: The results of an experimental program conducted on seventeen simply supported concrete beams to study the effect of transverse reinforcement on the behavior of lap splice of steel reinforcement in tension zones in high strength concrete beams, are presented. The parameters included in the experimental program were the concrete compressive strength, the lap splice length, the amount of transverse reinforcement provided within the splice region, and the shape of transverse reinforcement around spliced bars. The experimental results showed that the displacement ductility increased and the mode of failure changed from splitting bond failure to flexural failure when the amount of transverse reinforcement in splice region increased, and the compressive strength increased up to 100 MPa. The presence of transverse reinforcement around spliced bars had pronounced effect on increasing the ultimate load, the ultimate deflection, and the displacement ductility. The prediction of maximum steel stresses for spliced bars using ACI 318-05 building code was compared with the experimental results. The comparison showed that the effect of transverse reinforcement around spliced bars has to be considered into the design equations for lap splice length in high strength concrete beams.
Abstract: This paper presents the results of a study aimed at establishing the temperature distribution during the welding of aluminum alloy plates by Pulsed Current Gas Tungsten Arc Welding (PCGTAW) and Constant Current Gas Tungsten Arc Welding (CCGTAW) processes. Pulsing of the GTA welding current influences the dimensions and solidification rate of the fused zone, it also reduces the weld pool volume hence a narrower bead. In this investigation, the base material considered was aluminum alloy AA 6351 T6, which is finding use in aircraft, automobile and high-speed train components. A finite element analysis was carried out using ANSYS, and the results of the FEA were compared with the experimental results. It is evident from the study that the finite element analysis using ANSYS can be effectively used to model PCGTAW process for finding temperature distribution.
Abstract: A numerical simulation of optimization all of electrospinning processing parameters to obtain smallest nanofiber diameter have been performed by employing genetic algorithm (GA). Fitness function in genetic algorithm methods, which was different for each parameter, was determined by simulation approach based on the Reneker’s model. Moreover, others genetic algorithm parameter, namely length of population, crossover and mutation were applied to get the optimum electrospinning processing parameters. In addition, minimum fiber diameter, 32 nm, was achieved from a simulation by applied the optimum parameters of electrospinning. This finding may be useful for process control and prediction of electrospun fiber production. In this paper, it is also compared between predicted parameters with some experimental results.
Abstract: Theoretical investigations are performed by DFT method of B3LYP/6-31G+(2d,p) and B3LYP/6-311G+(2d,p) basis sets for three carbonyl thiourea compounds, namely N-[(2,6-Diethylphenyl)carbamothioyl]-2,2-diphenylacetamide (Compound I), N-[(3-Ethylphenyl)carbamothioyl]-2,2-diphenylacetamide (Compound II) and 2,2-Diphenyl-N-{[2-(trifluoromethyl)phenyl]carbamothioyl}acetamide (Compound III). Theoretical calculations for bond parameters, harmonic vibration frequencies and isotropic chemical shifts are in good agreement with the experimental results. The calculated molecular vibrations show good correlation values, which are 0.998 and 0.999 with the experimental data. The energy gap for compounds I, II and III calculated at B3LYP/6-31G+(2d,p) basis set are 4.455866117, 4.297495791 and 4.313550514 eV respectively, while for B3LYP/6-311G+(2d,p) basis set the energy gap obtained are 4.453689205 (Compound I), 4.311373603 (Compound II) and 4.315727426 (Compound III) eV.
Abstract: Implementing significant advantages in the supply of self-compacting concrete (SCC) is necessary because of the, negative features of SCC. Examples of these features are the ductility problem along with the very high cost of its constituted materials. Silica fume with steel fiber can fix this matter by improving the ductility and decreasing the total cost of SCC by varying the cement ingredients. Many different researchers have found that there have not been enough research carried out on the steel fiber-reinforced self-compacting concrete (SFRSCC) produced with silica fume. This paper inspects both the fresh and the mechanical properties of SFRSCC with silica fume, the fresh qualities where slump flow, slump T50 and V- funnel. While, the mechanical characteristics were the compressive strength, ultrasound pulse velocity (UPV) and elastic modulus of the concrete samples. The experimental results have proven that steel fiber can enhance the mechanical features. In addition, the silica fume within the entire hybrid mix may possibly adapt the fiber dispersion and strengthen deficits due to the fibers. It could also improve the strength plus the bond between the fiber and the matrix with a dense calcium silicate-hydrate gel in SFRSCC. The concluded result was predicted using linear mathematical models and was found to be in great agreement with the experimental results.
Abstract: Existence of plastic equation of state has been investigated by performing a series of load relaxation tests at various temperatures using an Al-Li alloy. A plastic equation of state is first developed from a simple kinetics consideration for a mechanical activation process of a leading dislocation piled up against grain boundaries. A series of load relaxation test has been conducted at temperatures ranging from 200 to 530oC to obtain the stress-strain rate curves. A plastic equation of state has been derived from a simple consideration of dislocation kinetics and confirmed by experimental results.
Abstract: In this paper, 3D image based composite unit cell is constructed from high resolution tomographic images. Through-thickness thermal diffusivity and in-plane Young’s modulus are predicted for the composite unit cell. The accuracy of the image based composite unit cell is tested by comparing its results with the experimental results obtained from laser flash and tensile test. The FE predictions are in close agreement with experimental results. Through-thickness thermal diffusivity and in-plane Young’s modulus of a virgin C/C composite are predicted by replacing the properties of air (porosity) with the properties of carbon matrix. The effect of porosity was found to be more profound on thermal diffusivity than young’s modulus.
Abstract: Axial compression tests are performed on circular tubes made of Aluminum EN AW 6060 (AlMgSi0.5 alloy) in T66 state. All the received tubes have the uniform outer diameter of 40mm and thickness of 1.5mm. Two different lengths 100mm and 200mm are used in the analysis. After performing compression tests on the uniform tube, important crashworthy parameters like peak force, average force, crush efficiency and energy absorption are measured. The present paper has given importance to increase the percentage of crush efficiency without decreasing the value energy absorption of a tube, so a circumferential notch was introduced on the top section of the tube. The effects of position and cut-out lengths of a circumferential notch on the crush efficiency are well explained with relative deformation modes and force-displacement curves. The numerical simulations were carried on the software tool ANSYS/LS-DYNA. It is seen that the numerical results are reasonably good in agreement with the experimental results.
Abstract: In this paper, we present a localization of a mobile robot with localization modules which have two ceiling-view cameras in indoor environments. We propose two kinds of localization method. The one is the localization in the local space; we use the line feature and the corner feature between the ceiling and wall. The other is the localization in the large space; we use the natural features such as bulbs, structures on the ceiling. These methods are installed on the embedded module able to mount on the robot. The embedded module has two cameras to be able to localize in both the local space and the large spaces. The experiment is practiced in our indoor test-bed and a government office. The proposed method is proved by the experimental results.
Abstract: This article is presented an experimental and modeling
study of a four-bed pressure swing adsorption process using
zeolite13X to provide oxygen-enriched air. The binary mixture N2/O2
(79/21 vol %) was used as a feed stream. The effects of purge/feed
ratio (P/F), adsorption pressure, cyclic time and product flow rate on
product purity and recovery under nonisothermal condition were
studied. The adsorption dynamics of process were determined using
a mathematical model incorporated mass and energy balances. A
Mathlab code using finite difference method was developed to solve
the set of coupled differential-algebraic equations, and the simulation
results are agreed well with experimental results.
Abstract: In the present study, computational fluid dynamics
(CFD) simulation has been executed to investigate the transition
boundaries of different flow patterns for moderately viscous oil-water
(viscosity ratio 107, density ratio 0.89 and interfacial tension of 0.032
N/m.) two-phase flow through a horizontal pipeline with internal
diameter and length of 0.025 m and 7.16 m respectively. Volume of
Fluid (VOF) approach including effect of surface tension has been
employed to predict the flow pattern. Geometry and meshing of the
present problem has been drawn using GAMBIT and ANSYS
FLUENT has been used for simulation. A total of 47037 quadrilateral
elements are chosen for the geometry of horizontal pipeline. The
computation has been performed by assuming unsteady flow,
immiscible liquid pair, constant liquid properties, co-axial flow and a
T-junction as entry section. The simulation correctly predicts the
transition boundaries of wavy stratified to stratified mixed flow.
Other transition boundaries are yet to be simulated. Simulated data
has been validated with our own experimental results.
Abstract: The motion of a sphere moving along the axis of a
rotating viscous fluid is studied at high Reynolds numbers and
moderate values of Taylor number. The Higher Order Compact
Scheme is used to solve the governing Navier-Stokes equations. The
equations are written in the form of Stream function, Vorticity
function and angular velocity which are highly non-linear, coupled
and elliptic partial differential equations. The flow is governed by
two parameters Reynolds number (Re) and Taylor number (T). For
very low values of Re and T, the results agree with the available
experimental and theoretical results in the literature. The results are
obtained at higher values of Re and moderate values of T and
compared with the experimental results. The results are fourth order
accurate.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.