Abstract: Medicinal plants are most suitable crops for ecological production systems because of their role in human health and the aim of sustainable agriculture to improve ecosystem efficiency and its products quality. Calculations include energy output (contents of energy in seed) and energy inputs (consumption of fertilizers, pesticides, labor, machines, fuel and electricity). The ratio of output of the production to inputs is called the energy outputs / inputs ratio or energy efficiency. One way to quantify essential parts of agricultural development is the energy flow method. The output / input energy ratio is proposed as the most comprehensive single factor in pursuing the objective of sustainability. Sylibum marianum L. is one of the most important medicinal plants in Iran and has effective role on health of growing population in Iran. The objective of this investigation was to find out energy efficiency in conventional and low input production system of Milk thistle. This investigation was carried out in the spring of 2005 – 2007 in the Research Station of Rangelands in Hamand - Damavand region of IRAN. This experiment was done in split-split plot based on randomized complete block design with 3 replications. Treatments were 2 production systems (Conventional and Low input system) in the main plots, 3 planting time (25 of March, 4 and 14 of April) in the sub plots and 2 seed types (Improved and Native of Khoozestan) in the sub-sub plots. Results showed that in conventional production system energy efficiency, because of higher inputs and less seed yield, was less than low input production system. Seed yield was 1199.5 and 1888 kg/ha in conventional and low input systems, respectively. Total energy inputs and out puts for conventional system was 10068544.5 and 7060515.9 kcal. These amounts for low input system were 9533885.6 and 11113191.8 kcal. Results showed that energy efficiency for seed production in conventional and low input system was 0.7 and 1.16, respectively. So, milk thistle seed production in low input system has 39.6 percent higher energy efficiency than conventional production system. Also, higher energy efficiency were found in sooner planting time (25 of March) and native seed of Khoozestan.
Abstract: The heat storage capacity of concrete in building shells is a major reason for excessively large electricity consumption induced by indoor air conditioning. In this research, the previously developed Smart Temperature Information Material (STIM) is embedded in two groups of exterior wall specimens (the control group contains reinforced concrete exterior walls and the experimental group consists of tiled exterior walls). Long term temperature measurements within the concrete are taken by the embedded STIM. Temperature differences between the control group and the experimental group in walls facing the four cardinal directions (east, west, south, and north) are evaluated. This study aims to provide a basic reference for the design of exterior walls and the selection of heat insulation materials.
Abstract: This paper presents the influence of distributed generation (DG) on congestion and locational marginal price (LMP) in an optimal power flow (OPF) based wholesale electricity market. The problem of optimal placement to manage congestion and reduce LMP is formulated for the objective of social welfare maximization. From competitive electricity market standpoint, DGs have great value when they reduce load in particular locations and at particular times when feeders are heavily loaded. The paper lies on the groundwork that solution to optimal mix of generation and transmission resources can be achieved by addressing congestion and corresponding LMP. Obtained as lagrangian multiplier associated with active power flow equation for each node, LMP gives the short run marginal cost (SRMC) of electricity. Specific grid locations are examined to study the influence of DG penetration on congestion and corresponding shadow prices. The influence of DG on congestion and locational marginal prices has been demonstrated in a modified IEEE 14 bus test system.
Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This paper presents one comprehensive modelling approach for maintenance scheduling problem of thermal power units in competitive market. This problem is formulated as a 0/1 mixedinteger linear programming model. Model incorporates long-term bilateral contracts with defined profiles of power and price, and weekly forecasted market prices for market auction. The effectiveness of the proposed model is demonstrated through case study with detailed discussion.
Abstract: Generation of electricity from coal has increased over
the years in the United States and around the world. Burning of coal
results in annual production of upwards of 100 millions tons (United
States only) of coal combustion products (CCPs). Only about a third
of these products are being used to create new products while the
remainder goes to landfills. Application of CCPs mixed with
composted organic materials onto soil can improve the soil-s
physico-chemical conditions and provide essential plant nutritients.
Our objective was to create plant growth media utilizing CCPs and
compost in way which maximizes the use of these products and, at
the same time, maintain good plant growth. Media were formulated
by adding composted organic matter (COM) to CCPs at ratios
ranging from 2:8 to 8:2 (v/v). The quality of these media was
evaluated by measuring their physical and chemical properties and
their effect on plant growth. We tested the media by 1) measuring
their physical and chemical properties and 2) the growth of three
plant species in the experimental media: wheat (Triticum sativum),
tomato (Lycopersicum esculentum) and marigold (Tagetes patula).
We achieved significantly (p < 0.001) higher growth (7-130%) in the
experimental media containing CCPs compared to a commercial mix.
The experimental media supplied adequate plant nutrition as no
fertilization was provided during the experiment. Based on the
results, we recommend the use of CCPs and composts for the
creation of plant growth media.
Abstract: Cogeneration may be defined as a system which
contains electricity production and regain of the thermo value of
exhaust gases simultaneously. The examination is based on the data-s
of an active cogeneration plant. This study, it is aimed to determine
which component of the system should be revised first to raise the
efficiency and decrease the loss of exergy. For this purpose, second
law analysis of thermodynamics is applied to each component due to
consider the effects of environmental conditions and take the quality
of energy into consideration as well as the quantity of it. The exergy
balance equations are produced and exergy loss is calculated for each
component. 44,44 % loss of exergy in heat exchanger, 29,59 % in
combustion chamber, 18,68 % in steam boiler, 5,25 % in gas turbine
and 2,03 % in compressor is calculated.
Abstract: Thermal-driven refrigeration systems have attracted increasing research and development interest in recent years. These systems do not cause ozone depletion and can reduce demand on electricity. The main objective of this work is to perform theoretical analyses of a thermal-driven refrigeration system using a new sorbent-sorptive pair as the working pair. The active component of sorbent is sodium thiocyanate (NaSCN). Ammonia (NH3) is chosen as sorptive. Based on the thermodynamic properties of the working solution, a mathematical model is introduced to analyze the system characteristics and performance. The results are used to compare with other thermal-driven refrigeration systems. It is shown that the advantages provided by this system over other absorption units include lower generator and evaporator temperatures, a higher coefficient of performance (COP). The COP is about 10 percent higher than the ones for the NH3-H2O system working at the same conditions.
Abstract: Combining energy efficiency with renewable energy
sources constitutes a key strategy for a sustainable future. The wind
power sector stands out as a fundamental element for the
achievement of the European renewable objectives and Portugal is no
exception to the increase of the wind energy for the electricity
generation. This work proposes an optimization model for the long
range electricity power planning in a system similar to the
Portuguese one, where the expected impacts of the increasing
installed wind power on the operating performance of thermal power
plants are taken into account. The main results indicate that the
increasing penetration of wind power in the electricity system will
have significant effects on the combined cycle gas power plants
operation and on the theoretically expected cost reduction and
environmental gains. This research demonstrated the need to address
the impact that energy sources with variable output may have, not
only on the short-term operational planning, but especially on the
medium to long range planning activities, in order to meet the
strategic objectives for the energy sector.
Abstract: This paper describes interconnection between
technical and economical making decision. The reason of this dealing
could be different: poor technical condition, change of substation
(electrical network) regime, power transformer owner budget deficit
and increasing of tariff on electricity. Establishing of recommended
practice as well as to give general advice and guidance in economical
sector, testing, diagnostic power transformers to establish its
conditions, identify problems and provide potential remedies.
Abstract: Mobiles are considered to be the most frequently used
electronic items in world after electricity. It is probably the only
device that can be used by any gender with no age limits depending
on its functionality. This paper present the interactive interface of
Mobile and particularly aiming the use of advanced phones which are
also called smart phones. With the changes in the trend where users
are now moving from ordinary mobiles to the one with touch screens
and facilities such as WiFi and internet browsing.
Abstract: Energy consumption is one of the indices in
determining the levels of development of a nation. Therefore,
availability of energy supply to all sectors of life in any country is
crucial for its development. These exists shortage of all kinds of
energy, particularly electricity which is badly needed for economic
development. Electricity from the sun which is quite abundant in
most of the developing countries is used in rural areas to meet basic
electricity needs of a rural community. Today-s electricity supply in
Myanmar is generated by fuel generators and hydroelectric power
plants. However, far-flung areas which are away from National Grids
cannot enjoy the electricity generated by these sources. Since
Myanmar is a land of plentiful sunshine, especially in central and
southern regions of the country, the first form of energy- solar energy
could hopefully become the final solution to its energy supply
problem. The direct conversion of solar energy into electricity using
photovoltaic system has been receiving intensive installation not only
in developed countries but also in developing countries. It is mainly
intended to present solar energy potential and application in
Myanmar. It is also wanted to get the benefits of using solar energy
for people in remote areas which are not yet connected to the national
grids because of the high price of fossil fuel.
Abstract: Fuel cell is an emerging technology in the field
of renewable energy sources which has the capacity to replace
conventional energy generation sources. Fuel cell utilizes hydrogen
energy to produce electricity. The electricity generated by the fuel
cell can’t be directly used for a specific application as it needs
proper power conditioning. Moreover, the output power fluctuates
with different operating conditions. To get a stable output power
at an economic rate, power conditioning circuit is essential for fuel
cell. This paper implements a two-staged power conditioning unit for
fuel cell based distributed generation using hysteresis current control
technique.
Abstract: Over recent years, the number of building integrated photovoltaic (BIPV) installations for home systems have been increasing in Malaysia. The paper concerns an analysis - as part of current Research and Development (R&D) efforts - to integrate photovoltaics as an architectural feature of a detached house in the new satellite township of Putrajaya, Malaysia. The analysis was undertaken using calculation and simulation tools to optimize performance of BIPV home system. In this study, a the simulation analysis was undertaken for selected bungalow units based on a long term recorded weather data for city of Kuala Lumpur. The simulation and calculation was done with consideration of a PV panels' tilt and direction, shading effect and economical considerations. A simulation of the performance of a grid connected BIPV house in Kuala Lumpur was undertaken. This case study uses a 60 PV modules with power output of 2.7 kW giving an average of PV electricity output is 255 kWh/month..
Abstract: This paper mainly investigates the environmental and
economic impacts of worldwide use of electric vehicles. It can be
concluded that governments have good reason to promote the use of
electric vehicles. First, the global vehicles population is evaluated with
the help of grey forecasting model and the amount of oil saving is
estimated through approximate calculation. After that, based on the
game theory, the amount and types of electricity generation needed by
electronic vehicles are established. Finally, some conclusions on the
government-s attitudes are drawn.
Abstract: The aim of this contribution is to present a new
approach in modeling the electrical activity of the human heart. A
recurrent artificial neural network is being used in order to exhibit a
subset of the dynamics of the electrical behavior of the human heart.
The proposed model can also be used, when integrated, as a
diagnostic tool of the human heart system.
What makes this approach unique is the fact that every model is
being developed from physiological measurements of an individual.
This kind of approach is very difficult to apply successfully in many
modeling problems, because of the complexity and entropy of the
free variables describing the complex system. Differences between
the modeled variables and the variables of an individual, measured at
specific moments, can be used for diagnostic purposes. The sensor
fusion used in order to optimize the utilization of biomedical sensors
is another point that this paper focuses on. Sensor fusion has been
known for its advantages in applications such as control and
diagnostics of mechanical and chemical processes.
Abstract: Energy generated by the force of water in hydropower
can provide a more sustainable, non-polluting alternative to fossil
fuels, along with other renewable sources of energy, such as wind,
solar and tidal power, bio energy and geothermal energy. Small scale
hydroelectricity in Iran is well suited for “off-grid" rural electricity
applications, while other renewable energy sources, such as wind,
solar and biomass, can be beneficially used as fuel for pumping
groundwater for drinking and small scale irrigation in remote rural
areas or small villages. Small Hydro Power plants in Iran have very
low operating and maintenance costs because they consume no fossil
or nuclear fuel and do not involve high temperature processes. The
equipment is relatively simple to operate and maintain. Hydropower
equipment can adjust rapidly to load changes. The extended
equipment life provides significant economic advantages. Some
hydroelectric plants installed 100 years ago still operate reliably. The
Polkolo river is located on Karun basin at southwest of Iran. Situation
and conditions of Polkolo river are evaluated for construction of
small hydropower in this article. The topographical conditions and
the existence of permanent water from springs provide the suitability
to install hydroelectric power plants on the river Polkolo. The
cascade plant consists of 9 power plants connected with each other
and is having the total head as 1100m and discharge about 2.5cubic
meter per second. The annual production of energy is 105.5 million
kwh.
Abstract: Restructured electricity markets may provide
opportunities for producers to exercise market power maintaining
prices in excess of competitive levels. In this paper an oligopolistic
market is presented that all Generation Companies (GenCos) bid in a
Cournot model. Genetic algorithm (GA) is applied to obtain
generation scheduling of each GenCo as well as hourly market
clearing prices (MCP). In order to consider network constraints a
multiperiod framework is presented to simulate market clearing
mechanism in which the behaviors of market participants are
modelled through piecewise block curves. A mixed integer linear
programming (MILP) is employed to solve the problem. Impacts of
market clearing process on participants- characteristic and final
market prices are presented. Consequently, a novel multi-objective
model is addressed for security constrained optimal bidding strategy
of GenCos. The capability of price-maker GenCos to alter MCP is
evaluated through introducing an effective-supply curve. In addition,
the impact of exercising market power on the variation of market
characteristics as well as GenCos scheduling is studied.
Abstract: Economic Load Dispatch (ELD) is a method of determining
the most efficient, low-cost and reliable operation of a power
system by dispatching available electricity generation resources to
supply load on the system. The primary objective of economic
dispatch is to minimize total cost of generation while honoring
operational constraints of available generation resources. In this paper
an intelligent water drop (IWD) algorithm has been proposed to
solve ELD problem with an objective of minimizing the total cost of
generation. Intelligent water drop algorithm is a swarm-based natureinspired
optimization algorithm, which has been inspired from natural
rivers. A natural river often finds good paths among lots of possible
paths in its ways from source to destination and finally find almost
optimal path to their destination. These ideas are embedded into
the proposed algorithm for solving economic load dispatch problem.
The main advantage of the proposed technique is easy is implement
and capable of finding feasible near global optimal solution with
less computational effort. In order to illustrate the effectiveness of
the proposed method, it has been tested on 6-unit and 20-unit test
systems with incremental fuel cost functions taking into account the
valve point-point loading effects. Numerical results shows that the
proposed method has good convergence property and better in quality
of solution than other algorithms reported in recent literature.