Abstract: This contribution deals with the relationship between
communication effectiveness and the extent of communication
among organizational units. To facilitate communication between
employees and to increase the level of understanding, the knowledge
of communication tools is necessary. Recent experience has shown
that personal communication is critical for smooth running of
companies and cannot be fully replaced by any form of technical
communication devices.
Below are presented the outcomes of the research on the
relationship between the extent of communication among
organisational units and its efficiency.
Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: This article presents a performance comparison of an
interior mounted permanent magnet synchronous generator (IPMSG)
with a synchronous reluctance generator (SynRG) with the same size
for a wind application. It is found that using the same geometrical
dimensions, a SynRG can convert 74 % of the power that an IPMSG
can convert, while it has 80% of the IPMSG weight. Moreover it is
found that the efficieny for the IMPSG is 99% at rated power
compared to 98.7% for the SynRG.
Abstract: Using Dynamic Bayesian Networks (DBN) to model genetic regulatory networks from gene expression data is one of the major paradigms for inferring the interactions among genes. Averaging a collection of models for predicting network is desired, rather than relying on a single high scoring model. In this paper, two kinds of model searching approaches are compared, which are Greedy hill-climbing Search with Restarts (GSR) and Markov Chain Monte Carlo (MCMC) methods. The GSR is preferred in many papers, but there is no such comparison study about which one is better for DBN models. Different types of experiments have been carried out to try to give a benchmark test to these approaches. Our experimental results demonstrated that on average the MCMC methods outperform the GSR in accuracy of predicted network, and having the comparable performance in time efficiency. By proposing the different variations of MCMC and employing simulated annealing strategy, the MCMC methods become more efficient and stable. Apart from comparisons between these approaches, another objective of this study is to investigate the feasibility of using DBN modeling approaches for inferring gene networks from few snapshots of high dimensional gene profiles. Through synthetic data experiments as well as systematic data experiments, the experimental results revealed how the performances of these approaches can be influenced as the target gene network varies in the network size, data size, as well as system complexity.
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: The objectives were to identify cyanide-degrading
bacteria and study cyanide removal efficiency. Agrobacterium
tumefaciens SUTS 1 was isolated. This is a new strain of
microorganisms for cyanide degradation. The maximum growth rate
of SUTS 1 obtained 4.7 × 108 CFU/ml within 4 days. The cyanide
removal efficiency was studied at 25, 50, and 150 mg/L cyanide. The
residual cyanide, ammonia, nitrate, nitrite, pH, and cell counts were
analyzed. At 25 and 50 mg/L cyanide, SUTS 1 obtained similar
removal efficiency approximately 87.50%. At 150 mg/L cyanide,
SUTS 1 enhanced the cyanide removal efficiency up to 97.90%. Cell
counts of SUTS 1 increased when the cyanide concentration was set
at lower. The ammonia increased when the removal efficiency
increased. The nitrate increased when the ammonia decreased but the
nitrite did not detect in all experiments. pH values also increased
when the cyanide concentrations were set at higher.
Abstract: Cloud Computing is a new technology that helps us to
use the Cloud for compliance our computation needs. Cloud refers to a scalable network of computers that work together like Internet. An
important element in Cloud Computing is that we shift processing, managing, storing and implementing our data from, locality into the
Cloud; So it helps us to improve the efficiency. Because of it is new
technology, it has both advantages and disadvantages that are
scrutinized in this article. Then some vanguards of this technology
are studied. Afterwards we find out that Cloud Computing will have
important roles in our tomorrow life!
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: The performances of a thermoacoustic travelling-wave
refrigerator are presented. Developed in the frame of the European
project called THATEA, it is designed for providing 600 W at a
temperature of 233 K with an efficiency of 40 % relative to the
Carnot efficiency. This paper presents the device and the results of
the first measurements. For a cooling power of 210 W, a coefficient
of performance relative to Carnot of 30 % is achieved when the
refrigerator is coupled with an existing standing-wave engine.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: Region covariance (RC) descriptor is an effective
and efficient feature for visual tracking. Current RC-based tracking
algorithms use the whole RC matrix to track the target in video
directly. However, there exist some issues for these whole RCbased
algorithms. If some features are contaminated, the whole RC
will become unreliable, which results in lost object-tracking. In
addition, if some features are very discriminative to the
background, other features are still processed and thus reduce the
efficiency. In this paper a new robust tracking method is proposed,
in which the whole RC matrix is decomposed into several low rank
matrices. Those matrices are dynamically chosen and processed so
as to achieve a good tradeoff between discriminability and
complexity. Experimental results have shown that our method is
more robust to complex environment changes, especially either
when occlusion happens or when the background is similar to the
target compared to other RC-based methods.
Abstract: Firstly, research and development on RFID focuses on
manufacturing and retail sectors, because it can improve supply chain
efficiency. But, now a variety of field is considered the next research
area for Radio Frequency Identification (RFID). Although RFID is
infancy, RFID technology has great potential in power industry to
significantly reduce cost, and improve quality of power supply. To
complement the limitation of RFID, we adopt the WSN (Wireless
Sensor Network) technology. However, relevant experience is limited,
the challenge will be to derive requirement from business practice and
to determine whether it is possible or not. To explore this issue, we
conduct a case study on implementing power facility management
system using RFID/WSN in Korea Electric Power Corporation
(KEPCO). In this paper we describe requirement from power industry.
And we introduce design and implementation of the test bed.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The purpose of this study is to find natural gait of
biped robot such as human being by analyzing the COG (Center Of
Gravity) trajectory of human being's gait. It is discovered that human
beings gait naturally maintain the stability and use the minimum
energy. This paper intends to find the natural gait pattern of biped
robot using the minimum energy as well as maintaining the stability by
analyzing the human's gait pattern that is measured from gait image on
the sagittal plane and COG trajectory on the frontal plane. It is not
possible to apply the torques of human's articulation to those of biped
robot's because they have different degrees of freedom. Nonetheless,
human and 5-link biped robots are similar in kinematics. For this, we
generate gait pattern of the 5-link biped robot by using the GA
algorithm of adaptation gait pattern which utilize the human's ZMP
(Zero Moment Point) and torque of all articulation that are measured
from human's gait pattern. The algorithm proposed creates biped
robot's fluent gait pattern as that of human being's and to minimize
energy consumption because the gait pattern of the 5-link biped robot
model is modeled after consideration about the torque of human's each
articulation on the sagittal plane and ZMP trajectory on the frontal
plane. This paper demonstrate that the algorithm proposed is superior
by evaluating 2 kinds of the 5-link biped robot applied to each gait
patterns generated both in the general way using inverse kinematics
and in the special way in which by considering visuality and
efficiency.
Abstract: Multi-agent system is composed by several agents
capable of reaching the goal cooperatively. The system needs an agent
platform for efficient and stable interaction between intelligent agents.
In this paper we propose a flexible and scalable agent platform by
composing the containers with multiple hierarchical agent groups. It
also allows efficient implementation of multiple domain presentations
of the agents unlike JADE. The proposed platform provides both
group management and individual management of agents for
efficiency. The platform has been implemented and tested, and it can
be used as a flexible foundation of the dynamic multi-agent system
targeting seamless delivery of ubiquitous services.
Abstract: In rapidly changing market environment, firms are investing a lot of time and resources into new product development (NPD) projects to make profit and to obtain competitive advantage. However, failure rate of NPD projects is becoming high due to various internal and external risks which hinder successful NPD projects. To reduce the failure rate, it is critical that risks have to be managed effectively and efficiently through good strategy, and treated by optimal responses to minimize risk cost. Four strategies are adopted to handle the risks in this study. The optimal responses are characterized by high reduction of risk costs with high efficiency. This study suggests a framework to decide the optimal responses considering the core risks, risk costs, response efficiency and response costs for successful NPD projects. Both binary particles warm optimization (BPSO) and multi-objective particle swarm optimization (MOPSO) methods are mainly used in the framework. Although several limitations exist in use for real industries, the frame work shows good strength for handling the risks with highly scientific ways through an example.