Abstract: Hong Kong is a densely populated city suffering badly from the urban heat island effect. Green wall offers a means of ameliorating the situation but there are doubts over its suitability in Hong Kong’s unique environment. In this paper, we look at the potential for green walls in Hong Kong first by summarizing some of the Chinese green walling systems and associated vegetation in use, then by an introduction to three existing green walls in Hong Kong, and finally through a small experiment aimed at identifying the likely main effects of green walled housing.
The results indicate that green walling in Hong Kong is likely to provide enhanced internal house environment in terms of warm weather temperature reduction, stabilization and damping, with direct energy savings in air-conditioning and indirect district benefits of reduced heat island effect and carbon emissions. The green walling insulation properties also suggest the possibility of warmer homes in winter and/or energy savings in mechanical heating provision.
Abstract: This paper proposes an alternating discharge method of multiple battery cells to extend battery operation time. In the proposed method, two battery cells are periodically connected in turn to a mobile device and only one cell supply power while the other rests. Battery operation time of the connecting cell decreases due to rate-capacity effect, while that of the resting cell increases due to recovery effect. These two effects conflict each other, but recovery effect is generally larger than rate-capacity effect and battery lifetime is extended. It was found from the result that battery operation time increase about 7% by using alternating battery cell discharge.
Abstract: In this paper, a power laterally-diffused metal-oxide-semiconductor field-effect transistor (LDMOSFET) on In0.53Ga0.47As is presented. The device utilizes a thicker field-oxide with low dielectric constant under the field-plate in order to achieve possible reduction in device capacitances and reduced-surface-field effect. Using 2D numerical simulations, performance of the proposed device is analyzed and compared with that of the conventional LDMOSFET. The proposed structure provides 50% increase in the breakdown voltage, 21% increase in transit frequency, and 72% improvement in figure-of-merit over the conventional device for same cell pitch.
Abstract: This study examines the stack ventilation performance of an office building located in Taipei, Taiwan. Atriums in this building act as stacks that facilitate buoyancy-driven ventilation. Computational Fluid Dynamic (CFD) simulations are used to identify interior airflow patterns, and then used these patterns to assess the building’s heat expulsion efficiency. Ambient temperatures of 20°C were adopted as the typical seasonal spring temperature range in Taipei. Further, “zero-wind” conditions are established to ensure simulation results reflected only the buoyancy effect. After checking results against neutral pressure level (NPL) level, airflow, air velocity, and indoor temperature stratification, the lower stack is modified to reduce the NPL in order to remove heat accumulated on the top floor.
Abstract: A method is proposed to extract faithful representative patterns from data set of observations when they are suffering from non-negligible fluctuations. Supposing time interval between measurements to be extremely small compared to observation time, it consists in defining first a subset of intermediate time intervals characterizing coherent behavior. Data projection on these intervals gives a set of curves out of which an ideally “perfect” one is constructed by taking the sup limit of them. Then comparison with average real curve in corresponding interval gives an efficiency parameter expressing the degradation consecutive to fluctuation effect. The method is applied to sunlight data collected in a specific place, where ideal sunlight is the one resulting from direct exposure at location latitude over the year, and efficiency is resulting from action of meteorological parameters, mainly cloudiness, at different periods of the year. The extracted information already gives interesting element of decision, before being used for analysis of plant control.
Abstract: Absorption spectra of infra-red (IR) radiation of the
disperse water medium absorbing the most important greenhouse
gases: CO2 , N2O , CH4 , C2H2 , C2H6 have been calculated by
the molecular dynamics method. Loss of the absorbing ability at the
formation of clusters due to a reduction of the number of centers
interacting with IR radiation, results in an anti-greenhouse effect.
Absorption of O3 molecules by the (H2O)50 cluster is investigated
at its interaction with Cl- ions. The splitting of ozone molecule on
atoms near to cluster surface was observed. Interaction of water
cluster with Cl- ions causes the increase of integrated intensity of
emission spectra of IR radiation, and also essential reduction of the
similar characteristic of Raman spectrum. Relative integrated
intensity of absorption of IR radiation for small water clusters was
designed. Dependences of the quantity of weight on altitude for
vapor of monomers, clusters, droplets, crystals and mass of all
moisture were determined. The anti-greenhouse effect of clusters was
defined as the difference of increases of average global temperature
of the Earth, caused by absorption of IR radiation by free water
molecules forming clusters, and absorption of clusters themselves.
The greenhouse effect caused by clusters makes 0.53 K, and the antigreenhouse
one is equal to 1.14 K. The increase of concentration of
CO2 in the atmosphere does not always correlate with the
amplification of greenhouse effect.
Abstract: In this paper we propose a new classification method for automatic sleep scoring using an artificial neural network based decision tree. It attempts to treat sleep scoring progress as a series of two-class problems and solves them with a decision tree made up of a group of neural network classifiers, each of which uses a special feature set and is aimed at only one specific sleep stage in order to maximize the classification effect. A single electroencephalogram (EEG) signal is used for our analysis rather than depending on multiple biological signals, which makes greatly simplifies the data acquisition process. Experimental results demonstrate that the average epoch by epoch agreement between the visual and the proposed method in separating 30s wakefulness+S1, REM, S2 and SWS epochs was 88.83%. This study shows that the proposed method performed well in all the four stages, and can effectively limit error propagation at the same time. It could, therefore, be an efficient method for automatic sleep scoring. Additionally, since it requires only a small volume of data it could be suited to pervasive applications.
Abstract: In this paper the principle, basic torque theory and design optimisation of a six-phase reluctance dc machine are considered. A trapezoidal phase current waveform for the machine drive is proposed and evaluated to minimise ripple torque. Low cost normal laminated salient-pole rotors with and without slits and chamfered poles are investigated. The six-phase machine is optimised in multi-dimensions by linking the finite-element analysis method directly with an optimisation algorithm; the objective function is to maximise the torque per copper losses of the machine. The armature reaction effect is investigated in detail and found to be severe. The measured and calculated torque performances of a 35 kW optimum designed six-phase reluctance dc machine drive are presented.
Abstract: In this paper, we study the pulsatile flow of blood through stenotic arteries. The inner layer of arterial walls is modeled as a porous medium and human blood is assumed as an incompressible fluid. A numerical algorithm based on the finite element method is developed to simulate the blood flow through both the lumen region and the porous wall. The algorithm is then applied to study the flow behaviour and to investigate the significance of the non-Newtonian effect.
Abstract: Numerical studies on race car aerodynamics at wing
in ground effect have been carried out using a steady 3d, double
precision, pressure-based, and standard k-epsilon turbulence model.
Through various parametric analytical studies we have observed that
at a particular speed and ground clearance of the wings a favorable
negative lift was found high at a particular angle of attack for all the
physical models considered in this paper. The fact is that if the
ground clearance height to chord length (h/c) is too small, the
developing boundary layers from either side (the ground and the
lower surface of the wing) can interact, leading to an altered variation
of the aerodynamic characteristics at wing in ground effect. Therefore
a suitable ground clearance must be predicted throughout the racing
for a better performance of the race car, which obviously depends
upon the coupled effects of the topography, wing orientation with
respect to the ground, the incoming flow features and/or the race car
speed. We have concluded that for the design of high performance
and high speed race cars the adjustable wings capable to alter the
ground clearance and the angles of attack is the best design option for
any race car for racing safely with variable speeds.
Abstract: An experimental study is presented on the effect
of microstructural change on the Portevin-Le Chatelier effect
behaviour of Al-2.5%Mg alloy. Tensile tests are performed on
the as received and heat treated (at 400 ºC for 16 hours)
samples for a wide range of strain rates. The serrations
observed in the stress-time curve are investigated from
statistical analysis point of view. Microstructures of the
samples are characterized by optical metallography and X-ray
diffraction. It is found that the excess vacancy generated due
to heat treatment leads to decrease in the strain rate sensitivity
and the increase in the number of stress drop occurrences per
unit time during the PLC effect. The microstructural
parameters like domain size, dislocation density have no
appreciable effect on the PLC effect as far as the statistical
behavior of the serrations is considered.
Abstract: The tensile properties of Mg-3%Al nanocrystalline
alloys were investigated at different test environment. Bulk
nanocrystalline samples of these alloy was successfully prepared by
mechanical alloying (MA) followed by cold compaction, sintering,
and hot extrusion process. The crystal size of the consolidated milled
sample was calculated by X-Ray line profile analysis. The
deformation mechanism and microstructural characteristic at
different test condition was discussed extensively. At room
temperature, relatively lower value of activation volume (AV) and
higher value of strain rate sensitivity (SRS) suggests that new rate
controlling mechanism accommodating plastic flow in the present
nanocrystalline sample. The deformation behavior and the
microstructural character of the present samples were discussed in
details.
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: In this paper, we analyze the rotor eddy currents losses provoqued by the stator slot harmonics developed in the permanent magnets or pole pieces of synchronous machines. An analytical approach is presented to evaluate the effect of slot ripples on rotor field and losses calculation. This analysis is then tested on a model by 2D/3D finite element (FE) calculation. The results show a good agreement on loss calculations when skin effect is negligible and the magnet is considered.
Abstract: The effects of irrigation with dairy factory wastewater on soil properties were investigated at two sites that had received irrigation for > 60 years. Two adjoining paired sites that had never received DFE were also sampled as well as another seven fields from a wider area around the factory. In comparison with paired sites that had not received effluent, long-term wastewater irrigation resulted in an increase in pH, EC, extractable P, exchangeable Na and K and ESP. These changes were related to the use of phosphoric acid, NaOH and KOH as cleaning agents in the factory. Soil organic C content was unaffected by DFE irrigation but the size (microbial biomass C and N) and activity (basal respiration) of the soil microbial community were increased. These increases were attributed to regular inputs of soluble C (e.g. lactose) present as milk residues in the wastewater. Principal component analysis (PCA) of the soils data from all 11sites confirmed that the main effects of DFE irrigation were an increase in exchangeable Na, extractable P and microbial biomass C, an accumulation of soluble salts and a liming effect. PCA analysis of soil bacterial community structure, using PCR-DGGE of 16S rDNA fragments, generally separated individual sites from one another but did not group them according to irrigation history. Thus, whilst the size and activity of the soil microbial community were increased, the structure and diversity of the bacterial community remained unaffected.
Abstract: This paper examines the factors, which determine
R&D outsourcing behaviour at Japanese firms, from the viewpoints of
transaction cost and strategic management, since the latter half of the
1990s. This study uses empirical analysis, which involves the
application of large-sample data. The principal findings of this paper
are listed below. Firms that belong to a wider corporate group are more
active in executing R&D outsourcing activities. Diversification
strategies such as the expansion of product and sales markets have a
positive effect on the R&D outsourcing behaviour of firms. Moreover,
while quantitative R&D resources have positive influences on R&D
outsourcing, qualitative indices have no effect. These facts suggest
that R&D outsourcing behaviour of Japanese firms are consistent with
the two perspectives of transaction cost and strategic management.
Specifically, a conventional corporate group network plays an
important role in R&D outsourcing behaviour. Firms that execute
R&D outsourcing leverage 'old' networks to construct 'new' networks
and use both networks properly.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.
Abstract: In electronegative-electropositive gas mixtures plasma, at a total pressure varying in the range of ten to hundred Torr, the appearance of a quasi-mochromatization effect of the emitted radiation was reported. This radiation could be the result of the generating mechanisms at molecular level, which is the case of the excimer radiation but also at atomic level. Thus, in the last case, in (Ne+1%Ar/Xe+H2) gas mixtures plasma in a dielectric barrier discharge, this effect, called M-effect, consists in the reduction of the discharge emission spectrum practice at one single, strong spectral line with λ = 585.3 nm. The present paper is concerned with the characteristics comparative investigation of the principal reaction mechanisms involved in the quasi-monochromatization effect existence in the case of the excimer radiation, respectively of the Meffect. Also, the paper points out the role of the metastable electronegative atoms in the appearance of the monochromatization – effect at atomic level.