Abstract: The Chichiawan stream in the Wulin catchment in
Taiwan is the natural habitat of Formosan landlocked salmon. Human
and agriculture activities gradually worsen water quality and impact
the fish habitat negatively. To protect and manage Formosan
landlocked salmon habitat, it is important to understand a variety
land-uses affect on the watershed responses to storms. This study
discusses watershed responses to the dry-day before a storm event and
a variety of land-uses in the Wulin catchment. Under the land-use
planning in the Wulin catchment, the peak flows during typhoon
events do not have noticeable difference. However, the nutrient
exports can be highly reduced under the strategies of restraining
agriculture activities. Due to the higher affinity of P for soil than that
of N, the exports of TN from overall Wuling catchment were much
greater than Ortho-P. Agriculture mainly centralized in subbasin A,
which is the important source of nutrients in nonpoint source discharge.
The subbasin A supplied about 26% of the TN and 32% of the Ortho-P
discharge in 2004, despite the fact it only covers 19% area of the
Wuling catchment. The subbasin analysis displayed that the
agricultural subbasin A exports higher nutrients per unit area than
other forest subbasins. Additionally, the agricultural subbasin A
contributed a higher percentage to total Ortho-P exports compares to
TN. The results of subbasin analysis might imply the transport of
Ortho-P was similar to the particulate matter which was mainly
influenced by the runoff and affected by the desorption from soil
particles while the TN (dominated as nitrate-N) was mainly influenced
by base-flow.
Abstract: The implementation of Super-Ultra Low Emission
Vehicle standards requires more efficient exhaust gas purification. To
increase the efficiency of exhaust gas purification, an the adsorbent
capable of holding hydrocarbons up to 250-300 ОС should be
developed. The possibility to design such adsorbents by modification
of zeolites of mordenite type, ZSM-5 and NaY, using different
metals cations has been studied.
It has been shown that introducing Cr, Cs, Zn, Ni, Co, Li, Mn in
zeolites results in modification of the toluene TPD and toluene
sorption capacity.
5%LiZSM-5 zeolite exhibits the most attractive TPD curve, with
toluene desorption temperature ranging from 250 to 350ОС. The
sorption capacity of 5%Li-ZSM-5 is 0.4 mmol/g. NaY zeolite has the
highest sorption capacity, up to 2 mmol/g, and holds toluene up to
350ОС, but at 120ОС toluene desorption starts, which is not desirable,
since the adsorbent of cold start hydrocarbons should retain them
until 250-300ОС. Therefore 5%LiZSM-5 zeolite was found to be the
most promising to control the cold-start hydrocarbon emissions
among the samples studied.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: From environmental aspect purification of ammonia
containing wastewater is expected. High efficiency ammonia
desorption can be done from the water by air on proper temperature.
After the desorption process, ammonia can be recovered and used in
another technology. The calculation method described below give
some methods to find either the minimum column height or ammonia
rich solution of the effluent.
Abstract: Effect of high temperature exposure on properties of cement mortar containing municipal solid waste incineration (MSWI) bottom ash as partial natural aggregate replacement is analyzed in the paper. The measurements of mechanical properties, bulk density, matrix density, total open porosity, sorption and desorption isotherms are done on samples exposed to the temperatures of 20°C to 1000°C. TGA analysis is performed as well. Finally, the studied samples are analyzed by IR spectroscopy in order to evaluate TGA data.
Abstract: Low silica type X (LSX) Zeolite is one of useful
material in many manufacturing due to the advantage properties
including high surface area, stability, microporous crystalline
aluminosilicates and positive ion in an extra–framework. The LSX
was used rice husk silica source which obtained by leaching with
hydrochloric acid and calcination at 500 C. To improve the
synthesis method, the LSX was crystallizated in Teflon–lined
autoclave will expedite deceasing of the amorphous particles. The
mixed gel with composition of 5.5 Na2O : 1.65 K2O : Al2O3 : 2.2
SiO2 : 122 H2O was crystallized in different container
(Polypropylene bottom and Teflon–lined autoclave). The obtained
powder was characterized by X–ray diffraction (XRD), X–ray
fluorescence spectrometry, N2 adsorption-desorption analysis BET
surface area Scanning electron microscopy (SEM) and Fourier
transform infrared spectroscopy to justify the quality of zeolite. The
results showed the crystallized zeolite in Teflon lined autoclave has
102.8 nm of crystal size, 286 m2/g of surface area and fewer amounts
of round amorphous particles when compared with the crystallized
zeolite in Polypropylene.
Abstract: Smoke from domestic wood burning has been
identified as a major contributor to air pollution, motivating detailed
emission measurements under controlled conditions. A series of
experiments was performed to characterise the emissions from wood
combustion in a fireplace and in a woodstove of two common species
of trees grown in Spain: Pyrenean oak (Quercus pyrenaica) and
black poplar (Populus nigra). Volatile organic compounds (VOCs) in
the exhaust emissions were collected in Tedlar bags, re-sampled in
sorbent tubes and analysed by thermal desorption-gas
chromatography-flame ionisation detection. Pyrenean oak presented
substantially higher emissions in the woodstove than in the fireplace,
for the majority of compounds. The opposite was observed for
poplar. Among the 45 identified species, benzene and benzenerelated
compounds represent the most abundant group, followed by
oxygenated VOCs and aliphatics. Emission factors obtained in this
study are generally of the same order than those reported for
residential experiments in the USA.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: A solar refrigeration system based on the adsorptiondesorption
phenomena is designed and analyzed. An annular tubular
generator filled with silica gel adsorbent and with a perforated inner
cylinder is integrated within a flat solar collector. The working fluid
in the refrigeration cycle is water. The thermodynamic analysis and
because of the temperature level that could be attained with a flat
solar collector it is required that the system operates under vacuum
conditions. In order to enhance the performance of the system and to
get uniform temperature in the silica gel and higher desorbed mass,
an apparatus for rotation of the generator is incorporated in the
system. Testing is carried out and measurements are taken on the
designed installation. The effect of rotation is checked on the
temperature distribution and on the performance of this machine and
compared to the flat solar collector with fixed generator.
Abstract: A new chelating resin is prepared by coupling
Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer.
The resulting sorbent has been characterized by FT-IR, elemental
analysis and thermogravimetric analysis (TGA) and studied for
preconcentrating of Cu (II) using flame atomic absorption
spectrometry (FAAS) for metal monitoring. The optimum pH value
for sorption of the copper ions was 6.5. The resin was subjected to
evaluation through batch binding of mentioned metal ion.
Quantitative desorption occurs instantaneously with 0.5 M HNO3.
The sorption capacity was found 4.8 mmol.g-1 of resin for Cu (II) in
the aqueous solution. The chelating resin can be reused for 10 cycles
of sorption-desorption without any significant change in sorption
capacity. A recovery of 99% was obtained the metal ions with 0.5 M
HNO3 as eluting agent. The method was applied for metal ions
determination from industrial waste water sample.
Abstract: The adsorption properties of CO and H2 on iron-based
catalyst with addition of Zr and Ni were investigated using
temperature programmed desorption process. It was found that on the
carburized iron-based catalysts, molecular state and dissociative state
CO existed together. The addition of Zr was preferential for the
molecular state adsorption of CO on iron-based catalyst and the
presence of Ni was beneficial to the dissociative adsorption of CO. On
H2 reduced catalysts, hydrogen mainly adsorbs on the surface iron
sites and surface oxide sites. On CO reduced catalysts, hydrogen
probably existed as the most stable CH and OH species. The addition
of Zr was not benefit to the dissociative adsorption of hydrogen on
iron-based catalyst and the presence of Ni was preferential for the
dissociative adsorption of hydrogen.
Abstract: The voltage/current characteristics and the effect of
NO2 gas on the electrical conductivity of a PbPc gas sensor array is
investigated. The gas sensor is manufactured using vacuum
deposition of gold electrodes on sapphire substrate with the leadphathalocyanine
vacuum sublimed on the top of the gold electrodes.
Two versions of the PbPc gas sensor array are investigated. The
tested types differ in the gap sizes between the deposited gold
electrodes. The sensors are tested at different temperatures to account
for conductivity changes as the molecular adsorption/desorption rate
is affected by heat. The obtained results found to be encouraging as
the sensors shoed stability and sensitivity towards low concentration
of applied NO2 gas.
Abstract: Hydrodesulfurization (HDS) of dibenzothiophene
(DBT) in a high pressure batch reactor was done at 320 °C on
CoMoS/Al2O3-B2O3 (4, 10, and 16 wt. % of Boria) using nhexadecane
as solvent, dimethyldisulfide (DMDS) in tetradecane as
sulfur agent, and stirring at 1000 rpm. The effects of boria were
investigated by using X-ray diffraction (XRD), Temperature
programmed desorption (TPD) of ammonia, and Brunauer-Emmet-
Teller (BET) experiments. The results showed that the catalyst
prepared with low boria content (4 wt. %) had HDS activity (in
pseudo first order kinetic constant basis) value ~1.45 times higher to
that of CoMoS/Al2O3 catalyst.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: Experimental investigation of the effect of
hydrophobic injection on siloxane basis on the properties of oldfashioned
type of ceramic brick is presented in the paper. At the
experimental testing, the matrix density, total open porosity, pore size
distribution, sorptivity, water absorption coefficient, sorption and
desorption isotherms are measured for the original, as well as the
hydrophobic-injection treated brick. On the basis of measured data,
the functionality of the hydrophobic injection for the moisture ingress
prevention into the studied ceramic brick is assessed.
Abstract: The current practice of determination of moisture diffusivity of building materials under laboratory conditions is predominantly aimed at the absorption phase. The main reason is the simplicity of the inverse analysis of measured moisture profiles. However, the liquid moisture transport may exhibit significant hysteresis. Thus, the moisture diffusivity should be different in the absorption (wetting) and desorption (drying) phase. In order to bring computer simulations of hygrothermal performance of building materials closer to the reality, it is then necessary to find new methods for inverse analysis which could be used in the desorption phase as well. In this paper we present genetic algorithm as a possible method of solution of the inverse problem of moisture transport in desorption phase. Its application is demonstrated for AAC as a typical building material.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: A new chelating resin is prepared by coupling Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer. The resulting sorbent has been characterized by FT-IR, elemental analysis and thermogravimetric analysis (TGA) and studied for preconcentrating of Fe (II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the iron ions was 6.5. The resin was subjected to evaluation through batch binding of mentioned metal ion. Quantitative desorption occurs instantaneously with 0.5 M HNO3. The sorption capacity was found 4.1 mmol.g-1 of resin for Fe (II) in the aqueous solution. The chelating resin can be reused for 10 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 97% was obtained the metal ions with 0.5 M HNO3 as eluting agent. The method was applied for metal ions determination from industrial waste water sample.