Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: A capacity spectrum method (CSM), one of methodologies to evaluate seismic fragilities of building structures, has been long recognized as the most convenient method, even if it contains several limitations to predict the seismic response of structures of interest. This paper proposes the procedure to estimate seismic fragility curves using an incremental dynamic analysis (IDA) rather than the method adopting a CSM. To achieve the research purpose, this study compares the seismic fragility curves of a 5-story reinforced concrete (RC) moment frame obtained from both methods; an IDA method and aCSM. Both seismic fragility curves are similar in slight and moderate damage states whereas the fragility curve obtained from the IDA method presents less variation (or uncertainties) in extensive and complete damage states. This is due to the fact that the IDA method can properly capture the structural response beyond yielding rather than the CSM and can directly calculate higher mode effects. From these observations, the CSM could overestimate seismic vulnerabilities of the studied structure in extensive or complete damage states.
Abstract: Examining existing experimental results for shallow
rigid foundations subjected to vertical centric load (N), accompanied
or not with a bending moment (M), two main non-linear mechanisms
governing the cyclic response of the soil-foundation system can be
distinguished: foundation uplift and soil yielding. A soil-foundation
failure limit, is defined as a domain of resistance in the two
dimensional (2D) load space (N, M) inside of which lie all the
admissible combinations of loads; these latter correspond to a pure
elastic, non-linear elastic or plastic behavior of the soil-foundation
system, while the points lying on the failure limit correspond to a
combination of loads leading to a failure of the soil-foundation
system. In this study, the proposed resistance domain is constructed
analytically based on mechanics. Original elastic limit, uplift
initiation limit and iso-uplift limits are constructed inside this
domain. These limits give a prediction of the mechanisms activated
for each combination of loads applied to the foundation. A
comparison of the proposed failure limit with experimental tests
existing in the literature shows interesting results. Also, the
developed uplift initiation limit and iso-uplift curves are confronted
with others already proposed in the literature and widely used due to
the absence of other alternatives, and remarkable differences are
noted, showing evident errors in the past proposals and relevant
accuracy for those given in the present work.
Abstract: The recommended limit for cadmium concentration in
potable water is less than 0.005 mg/L. A continuous biosorption
process using indigenous red seaweed, Gracilaria corticata, was
performed to remove cadmium from the potable water. The process
was conducted under fixed conditions and the breakthrough curves
were achieved for three consecutive sorption-desorption cycles. A
modeling based on Artificial Neural Network (ANN) was employed
to fit the experimental breakthrough data. In addition, a simplified
semi empirical model, Thomas, was employed for this purpose. It
was found that ANN well described the experimental data (R2>0.99)
while the Thomas prediction were a bit less successful with R2>0.97.
The adjusted design parameters using the nonlinear form of Thomas
model was in a good agreement with the experimentally obtained
ones. The results approve the capability of ANN to predict the
cadmium concentration in potable water.
Abstract: We present a trigonometric scheme to approximate a
circular arc with its two end points and two end tangents/unit
tangents. A rational cubic trigonometric Bézier curve is constructed
whose end control points are defined by the end points of the circular
arc. Weight functions and the remaining control points of the cubic
trigonometric Bézier curve are estimated by variational approach to
reproduce a circular arc. The radius error is calculated and found less
than the existing techniques.
Abstract: Different strategies and tools are available at the oil
and gas industry for detecting and analyzing tension and possible
fractures in borehole walls. Most of these techniques are based on
manual observation of the captured borehole images. While this
strategy may be possible and convenient with small images and few
data, it may become difficult and suitable to errors when big
databases of images must be treated. While the patterns may differ
among the image area, depending on many characteristics (drilling
strategy, rock components, rock strength, etc.). In this work we
propose the inclusion of data-mining classification strategies in order
to create a knowledge database of the segmented curves. These
classifiers allow that, after some time using and manually pointing
parts of borehole images that correspond to tension regions and
breakout areas, the system will indicate and suggest automatically
new candidate regions, with higher accuracy. We suggest the use of
different classifiers methods, in order to achieve different knowledge
dataset configurations.
Abstract: Characterization of the engineering behavior of
unsaturated soil is dependent on the soil-water characteristic curve
(SWCC), a graphical representation of the relationship between water
content or degree of saturation and soil suction. A reasonable
description of the SWCC is thus important for the accurate prediction
of unsaturated soil parameters. The measurement procedures for
determining the SWCC, however, are difficult, expensive, and timeconsuming.
During the past few decades, researchers have laid a
major focus on developing empirical equations for predicting the
SWCC, with a large number of empirical models suggested. One of
the most crucial questions is how precisely existing equations can
represent the SWCC. As different models have different ranges of
capability, it is essential to evaluate the precision of the SWCC
models used for each particular soil type for better SWCC estimation.
It is expected that better estimation of SWCC would be achieved via
a thorough statistical analysis of its distribution within a particular
soil class. With this in view, a statistical analysis was conducted in
order to evaluate the reliability of the SWCC prediction models
against laboratory measurement. Optimization techniques were used
to obtain the best-fit of the model parameters in four forms of SWCC
equation, using laboratory data for relatively coarse-textured (i.e.,
sandy) soil. The four most prominent SWCCs were evaluated and
computed for each sample. The result shows that the Brooks and
Corey model is the most consistent in describing the SWCC for sand
soil type. The Brooks and Corey model prediction also exhibit
compatibility with samples ranging from low to high soil water
content in which subjected to the samples that evaluated in this study.
Abstract: Mass flow measurement is the basis of most technoeconomic
formulations in the chemical industry. This calls for
reliable and accurate detection of mass flow. Flow measurement
laboratory experiments were conducted using various instruments.
These consisted of orifice plates, various sized rotameters, wet gas
meter and soap bubble meter. This work was aimed at evaluating
appropriate operating conditions and accuracy of the aforementioned
devices. The experimental data collected were compared to
theoretical predictions from Bernoulli’s equation and calibration
curves supplied by the instrument’s manufacturers. The results
obtained showed that rotameters were more reliable for measuring
high and low flow rates; while soap-bubble meters and wet-gas
meters were found to be suitable for measuring low flow rates. The
laboratory procedures and findings of the actual work can assist
engineering students and professionals in conducting their flow
measurement laboratory test work.
Abstract: A circularly polarized fractal boundary microstrip
antenna is presented. The sides of a square patch along x- axis, yaxis
are replaced with Minkowski and Koch curves correspondingly.
By using the fractal curves as edges, asymmetry in the structure is
created to excite two orthogonal modes for circular polarization (CP)
operation. The indentation factors of the fractal curves are optimized
for pure CP. The simulated results of the novel polyfractal antenna
are demonstrated.
Abstract: Kinematic data wisely correlate vector quantities in
space to scalar parameters in time to assess the degree of symmetry
between the intact limb and the amputated limb with respect to a
normal model derived from the gait of control group participants.
Furthermore, these particular data allow a doctor to preliminarily
evaluate the usefulness of a certain rehabilitation therapy.
Kinetic curves allow the analysis of ground reaction forces (GRFs)
to assess the appropriateness of human motion.
Electromyography (EMG) allows the analysis of the fundamental
lower limb force contributions to quantify the level of gait
asymmetry. However, the use of this technological tool is expensive
and requires patient’s hospitalization. This research work suggests
overcoming the above limitations by applying artificial neural
networks.
Abstract: Al-Si-Mg-Ni(-Cu) alloys are widely used in the automotive industry. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties – mainly at high temperatures. The corrosion resistance of these alloys in coastal area, particularly sea water, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization have been used to evaluate the corrosion resistance of Al-6Si-0.5Mg-2Ni (-2Cu) alloys in simulated sea water environments. The potentiodynamic polarization curves reveal that 2 wt% Cu content alloy (Alloy-2) is more prone to corrosion than the Cu free alloy (Alloy-1). But the EIS test results showed that corrosion resistance or charge transfer resistance (Rct) increases with the addition of Cu. Due to addition of Cu and thermal treatment, the magnitude of open circuit potential (OCP), corrosion potential (Ecorr) and pitting corrosion potential (Epit) of Al-6Si-0.5Mg-2Ni alloy in NaCl solution were shifted to the more noble direction.
Abstract: When it comes to last, it is regarded as the critical foundation of shoe design and development. Not only the last relates to the comfort of shoes wearing but also it aids the production of shoe styling and manufacturing. In order to enhance the efficiency and application of last development, a computer aided methodology for customized last form designs is proposed in this study. The reverse engineering is mainly applied to the process of scanning for the last form. Then the minimum energy is used for the revision of surface continuity, the surface of the last is reconstructed with the feature curves of the scanned last. When the surface of a last is reconstructed, based on the foundation of the proposed last form reconstruction module, the weighted arithmetic mean method is applied to the calculation on the shape morphing which differs from the grading for the control mesh of last, and the algorithm of subdivision is used to create the surface of last mesh, thus the feet-fitting 3D last form of different sizes is generated from its original form feature with functions remained. Finally, the practicability of the proposed methodology is verified through later case studies.
Abstract: In this paper, a backward semi-Lagrangian scheme
combined with the second-order backward difference formula
is designed to calculate the numerical solutions of nonlinear
advection-diffusion equations. The primary aims of this paper are
to remove any iteration process and to get an efficient algorithm
with the convergence order of accuracy 2 in time. In order to achieve
these objects, we use the second-order central finite difference and the
B-spline approximations of degree 2 and 3 in order to approximate
the diffusion term and the spatial discretization, respectively. For the
temporal discretization, the second order backward difference formula
is applied. To calculate the numerical solution of the starting point
of the characteristic curves, we use the error correction methodology
developed by the authors recently. The proposed algorithm turns out
to be completely iteration free, which resolves the main weakness
of the conventional backward semi-Lagrangian method. Also, the
adaptability of the proposed method is indicated by numerical
simulations for Burgers’ equations. Throughout these numerical
simulations, it is shown that the numerical results is in good
agreement with the analytic solution and the present scheme offer
better accuracy in comparison with other existing numerical schemes.
Abstract: This work presents a comparison study between the state-space and polynomial methods for the design of the robust governor for load frequency control of steam turbine power systems. The robust governor is synthesized using the two approaches and the comparison is extended to include time and frequency domains performance, controller order, and uncertainty representation, weighting filters, optimality and sub-optimality. The obtained results are represented through tables and curves with reasons of similarities and dissimilarities.
Abstract: In this paper, an analytical study is made for the dynamic behavior of human brain tissue under transient loading. In this analytical model the Mooney-Rivlin constitutive law is coupled with visco-elastic constitutive equations to take into account both the nonlinear and time-dependent mechanical behavior of brain tissue. Five ordinary differential equations representing the relationships of five main parameters (radial stress, circumferential stress, radial strain, circumferential strain, and particle velocity) are obtained by using the characteristic method to transform five partial differential equations (two continuity equations, one motion equation, and two constitutive equations). Analytical expressions of the attenuation properties for spherical wave in brain tissue are analytically derived. Numerical results are obtained based on the five ordinary differential equations. The mechanical responses (particle velocity and stress) of brain are compared at different radii including 5, 6, 10, 15 and 25 mm under four different input conditions. The results illustrate that loading curves types of the particle velocity significantly influences the stress in brain tissue. The understanding of the influence by the input loading cures can be used to reduce the potentially injury to brain under head impact by designing protective structures to control the loading curves types.
Abstract: This paper presents the use of phasor bond graphs to
obtain the steady-state behavior of a synchronous generator. The
phasor bond graph elements are built using 2D multibonds, which
represent the real and imaginary part of the phasor. The dynamic
bond graph model of a salient-pole synchronous generator is showed,
and verified viz. a sudden short-circuit test. The reduction of the
dynamic model into a phasor representation is described. The
previous test is executed on the phasor bond graph model, and its
steady-state values are compared with the dynamic response. Besides,
the widely used power (torque)-angle curves are obtained by means
of the phasor bond graph model, to test the usefulness of this model.
Abstract: This paper aims at experimental and numerical investigation of springback behavior of sheet metals during L-bending process with emphasis on Stribeck-type friction modeling. The coefficient of friction in Stribeck curve depends on sliding velocity and contact pressure. The springback behavior of mild steel and aluminum alloy 6022-T4 sheets was studied experimentally and using numerical simulations with ABAQUS software with two types of friction model: Coulomb friction and Stribeck friction. The influence of forming speed on springback behavior was studied experimentally and numerically. The results showed that Stribeck-type friction model has better results in predicting springback in sheet metal forming. The FE prediction error for mild steel and 6022-T4 AA is 23.8%, 25.5% respectively, using Coulomb friction model and 11%, 13% respectively, using Stribeck friction model. These results show that Stribeck model is suitable for simulation of sheet metal forming especially at higher forming speed.
Abstract: This paper presents a nonparametric method to obtain the hazard rate “Bathtub curve” for power system components. The model is a mixture of the three known phases of a component life, the decreasing failure rate (DFR), the constant failure rate (CFR) and the increasing failure rate (IFR) represented by three parametric Weibull models. The parameters are obtained from a simultaneous fitting process of the model to the Kernel nonparametric hazard rate curve. From the Weibull parameters and failure rate curves the useful lifetime and the characteristic lifetime were defined. To demonstrate the model the historic time-to-failure of distribution transformers were used as an example. The resulted “Bathtub curve” shows the failure rate for the equipment lifetime which can be applied in economic and replacement decision models.
Abstract: Semi-active Fuzzy control of quarter car system having three degrees of freedom and assembled with magneto-rheological (MR) shock absorber is studied in present paper. First, experimental work was performed on an MR shock absorber under different excitation conditions to obtain force-displacement and force-velocity curves. Then, for the application of experimental data in semi-active quarter car system, a polynomial model was selected. Finally, Fuzzy logic controller was designed having the combination of Forward fuzzy controller and Inverse fuzzy controller for integration in secondary suspension system of concerned model. The proposed controlled quarter car model was compared with uncontrolled system using simulation work under bump type of road excitation. Results obtained by simulation work shows the effectiveness of fuzzy controlled suspension system in improving the ride comfort and safety of travelling passengers compared to uncontrolled suspension system.
Abstract: The material properties of OFHC copper film was investigated with the High-Speed Material Micro Testing Machine (HSMMTM) at the high strain rates. The rate-dependent stress-strain curves from the experiment and the Johnson−Cook curve fitting showed large discrepancies as the plastic strain increases since the constitutive model implies no rate-dependent strain hardening effect. A new constitutive model was proposed in consideration of rate-dependent strain hardening effect. The strain rate hardening term in the new constitutive model consists of the strain rate sensitivity coefficients of the yield strength and strain hardening.