Abstract: Grasslands of Iran are encountered with a vast
desertification and destruction. Some legumes are plants of forage
importance with high palatability. Studied legumes in this project are
Onobrychis, Medicago sativa (alfalfa) and Trifolium repens. Seeds
were cultivated in research field of Kaboutarabad (33 km East of
Isfahan, Iran) with an average 80 mm. annual rainfall. Plants were
cultivated in a split plot design with 3 replicate and two water
treatments (weekly irrigation, and under stress with same amount per
15 days interval). Water entrance to each plots were measured by
Partial flow. This project lasted 20 weeks. Destructive samplings
(1m2 each time) were done weekly. At each sampling plants were
gathered and weighed separately for each vegetative parts. An Area
Meter (Vista) was used to measure root surface and leaf area. Total
shoot and root fresh and dry weight, leaf area index and soil coverage
were evaluated too. Dry weight was achieved in 750c oven after 24
hours. Statgraphic and Harvard Graphic software were used to
formulate and demonstrate the parameters curves due to time. Our
results show that Trifolium repens has affected 60 % and Medicago
sativa 18% by water stress. Onobrychis total fresh weight was
reduced 45%. Dry weight or Biomass in alfalfa is not so affected by
water shortage. This means that in alfalfa fields we can decrease the
irrigation amount and have some how same amount of Biomass.
Onobrychis show a drastic decrease in Biomass. The increases in
total dry matter due to time in studied plants are formulated. For
Trifolium repens if removal or cattle entrance to meadows do not
occurred at perfect time, it will decrease the palatability and water
content of the shoots. Water stress in a short period could develop the
root system in Trifolium repens, but if it last more than this other
ecological and soil factors will affect the growth of this plant. Low
level of soil water is not so important for studied legume forges. But
water shortage affect palatability and water content of aerial parts.
Leaf area due to time in studied legumes is formulated. In fact leaf
area is decreased by shortage in available water. Higher leaf area
means higher forage and biomass production. Medicago and
Onobrychis reach to the maximum leaf area sooner than Trifolium
and are able to produce an optimum soil cover and inhibit the
transpiration of soil water of meadows. Correlation of root surface to
Total biomass in studied plants is formulated. Medicago under water
stress show a 40% decrease in crown cover while at optimum
condition this amount reach to 100%. In order to produce forage in
areas without soil erosion Medicago is the best choice even with a
shortage in water resources. It is tried to represent the growth
simulation of three famous Forage Legumes. By growth simulation
farmers and range managers could better decide to choose best plant
adapted to water availability without designing different time and
labor consuming field experiments.
Abstract: This paper proposes a stroke extraction method for use in off-line signature verification. After giving a brief overview of the current ongoing researches an algorithm is introduced for detecting and following strokes in static images of signatures. Problems like the handling of junctions and variations in line width and line intensity are discussed in detail. Results are validated by both using an existing on-line signature database and by employing image registration methods.
Abstract: Finding suitable non-supersingular elliptic curves for
pairing-based cryptosystems becomes an important issue for the
modern public-key cryptography after the proposition of id-based
encryption scheme and short signature scheme. In previous work
different algorithms have been proposed for finding such elliptic
curves when embedding degree k ∈ {3, 4, 6} and cofactor h ∈ {1, 2, 3,
4, 5}. In this paper a new method is presented to find more
non-supersingular elliptic curves for pairing-based cryptosystems with
general embedding degree k and large values of cofactor h. In
addition, some effective parameters of these non-supersingular elliptic
curves are provided in this paper.
Abstract: In today-s competitive market, most companies
develop manufacturing systems that can help in cost reduction and
maximum quality. Human issues are an important part of
manufacturing systems, yet most companies ignore their effects on
production performance. This paper aims to developing an integrated
workforce planning system that incorporates the human being.
Therefore, a multi-objective mixed integer nonlinear programming
model is developed to determine the amount of hiring, firing,
training, overtime for each worker type. This paper considers a
workforce planning model including human aspects such as skills,
training, workers- personalities, capacity, motivation, and learning
rates. This model helps to minimize the hiring, firing, training and
overtime costs, and maximize the workers- performance. The results
indicate that the workers- differences should be considered in
workforce scheduling to generate realistic plans with minimum costs.
This paper also investigates the effects of human learning rates on the
performance of the production systems.
Abstract: In this work, position vector of a time-like dual curve
according to standard frame of D31
is investigated. First, it is proven
that position vector of a time-like dual curve satisfies a dual vector
differential equation of fourth order. The general solution of this dual
vector differential equation has not yet been found. Due to this, in
terms of special solutions, position vectors of some special time-like
dual curves with respect to standard frame of D31
are presented.
Abstract: The length of a given rational B'ezier curve is
efficiently estimated. Since a rational B'ezier function is nonlinear,
it is usually impossible to evaluate its length exactly. The
length is approximated by using subdivision and the accuracy
of the approximation n is investigated. In order to improve
the efficiency, adaptivity is used with some length estimator.
A rigorous theoretical analysis of the rate of convergence of
n to is given. The required number of subdivisions to
attain a prescribed accuracy is also analyzed. An application
to CAD parametrization is briefly described. Numerical results
are reported to supplement the theory.
Abstract: Due to the growing dynamic and complexity within
the market environment production enterprises in particular are faced
with new logistic challenges. Moreover, it is here in this dynamic
environment that the Logistic Operating Curve Theory also reaches
its limits as a method for describing the correlations between the
logistic objectives. In order to convert this theory into a method for
dynamically monitoring productions this paper will introduce
methods for reliably and quickly identifying structural changes
relevant to logistics.
Abstract: The motion planning procedure described in this paper has been developed in order to eliminate or reduce the residual vibrations of electromechanical positioning systems, without augmenting the motion time (usually imposed by production requirements), nor introducing overtime for vibration damping. The proposed technique is based on a suitable choice of the motion law assigned to the servomotor that drives the mechanism. The reference profile is defined by a Bezier curve, whose shape can be easily changed by modifying some numerical parameters. By means of an optimization technique these parameters can be modified without altering the continuity conditions imposed on the displacement and on its time derivatives at the initial and final time instants.
Abstract: The refueling of a transparent rectangular fuel tank
fitted with a standard filler pipe and roll-over valve was
experimentally studied. A fuel-conditioning cart, capable of
handling fuels of different Reid vapor pressure at a constant
temperature, was used to dispense fuel at the desired rate. The
experimental protocol included transient recording of the tank and
filler tube pressures while video recording the flow patterns in the
filler tube and tank during the refueling process. This information
was used to determine the effect of changes in the vent tube
diameter, fuel-dispense flow rate and fuel Reid vapor pressure on the
pressure-time characteristics and the occurrence of premature fuel
filling shut-off and fuel spill-back. Pressure-time curves for the case
of normal shut-off demonstrated the classic, three-phase
characteristic noted in the literature. The variation of the maximum
values of tank dome and filler tube pressures are analyzed in relation
to the occurrence of premature shut-off.
Abstract: The classical temporal scan statistic is often used to
identify disease clusters. In recent years, this method has become as a
very popular technique and its field of application has been notably
increased. Many bioinformatic problems have been solved with this
technique. In this paper a new scan fuzzy method is proposed. The
behaviors of classic and fuzzy scan techniques are studied with
simulated data. ROC curves are calculated, being demonstrated the
superiority of the fuzzy scan technique.
Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: A mathematical model for the transmission of SARS is developed. In addition to dividing the population into susceptible (high and low risk), exposed, infected, quarantined, diagnosed and recovered classes, we have included a class called untraced. The model simulates the Gompertz curves which are the best representation of the cumulative numbers of probable SARS cases in Hong Kong and Singapore. The values of the parameters in the model which produces the best fit of the observed data for each city are obtained by using a differential evolution algorithm. It is seen that the values for the parameters needed to simulate the observed daily behaviors of the two epidemics are different.
Abstract: The paper aims at investigating influence of medium
capacity on linear adsorbed solute dispersion into chemically
heterogeneous fixed beds. A discrete chemical heterogeneity
distribution is considered in the one-dimensional advectivedispersive
equation. The partial differential equation is solved using
finite volumes method based on the Adam-Bashforth algorithm.
Increased dispersion is estimated by comparing breakthrough curves
second order moments and keeping identical hydrodynamic
properties. As a result, dispersion increase due to chemical
heterogeneity depends on the column size and surprisingly on the
solid capacity. The more intense capacity is, the more important
solute dispersion is. Medium length which is known to favour this
effect vanishing according to the linear adsorption in fixed bed seems
to create nonmonotonous variation of dispersion because of the
heterogeneity. This nonmonotonous behaviour is also favoured by
high capacities.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: Fruit drying is a well known process mostly used for
preservation of fruits. Osmotic dehydration of apricot slices were
carried out in three different salt-sucrose concentrations and four
different temperatures. Also three different weight ratios of solution
to sample were conducted to one set of experiments. The dehydration
curves were constructed using Peleg-s model. Increasing the solution
volume increased the mass transfer rate and hence the solid gain
increased rapidly. Increasing the volume of osmotic media caused an
increase in overall mass transfer but a 'solution to sample' ratio of 5:1
gave the best product quality. The best temperature and concentration
that had a high water loss to solid gain ratio and an acceptable taste
were 40°C and 5%, respectively.
Abstract: In this work, we consider the rational points on elliptic curves over finite fields Fp where p ≡ 5 (mod 6). We obtain results on the number of points on an elliptic curve y2 ≡ x3 + a3(mod p), where p ≡ 5 (mod 6) is prime. We give some results concerning the sum of the abscissae of these points. A similar case where p ≡ 1 (mod 6) is considered in [5]. The main difference between two cases is that when p ≡ 5 (mod 6), all elements of Fp are cubic residues.
Abstract: Depressurization and pressurization streams in
industrial systems constitute a work exchange network (WEN). In this
paper, a novel graphical approach for targeting energy conservation
potential of a WEN is proposed. Through constructing the composite
work curves in the pressure-work diagram and assuming all of the
mechanical energy of the depressurization streams is recovered by
expanders, the maximum work target of a WEN can be determined via
the proposed targeting steps. A WEN in an ammonia production
process is used as a case study to illustrate the applicability of the
proposed graphical approach.
Abstract: This work presents a comparison between the Annual
Energy Output (AEO) of two commercial vertical-axis wind turbines
(VAWTs) for a low-wind urban site: both a drag-driven and a liftdriven
concepts are examined in order to be installed on top of the
new Via dei Giustinelli building, Trieste (Italy). The power-curves,
taken from the product specification sheets, have been matched to the
wind characteristics of the selected installation site. The influence of
rotor swept area and rated power on the performance of the two
proposed wind turbines have been examined in detail, achieving a
correlation between rotor swept area, electrical generator size and
wind distribution, to be used as a guideline for the calculation of the
AEO.
Abstract: This purpose of this paper is to present the acceptance single sampling plan when the fraction of nonconforming items is a fuzzy number and being modeled based on the fuzzy Poisson distribution. We have shown that the operating characteristic (oc) curves of the plan is like a band having a high and low bounds whose width depends on the ambiguity proportion parameter in the lot when that sample size and acceptance numbers is fixed. Finally we completed discuss opinion by a numerical example. And then we compared the oc bands of using of binomial with the oc bands of using of Poisson distribution.
Abstract: Deflocculation and gel characterization were
investigated for three different composition of porcelain slips at
specific gravity 1.8. The suspensions were dispersed with sodium
silicate (Na2SiO3) in under-deflocculated slips and fully deflocculated
slips. The rheology characterization of slips was conducted by the
deflocculation curves and the gel curves. The results showed that
decreasing the amount of the ball clay composition in the slips
consumed less dosages of the dispersants. The under-deflocculated
slips tended to have a gelation rate faster than the fully deflocculated
slips.