Abstract: In this study, an Artificial Neural Network (ANN)
analytical method has been developed for analyzing earthquake
performances of the Reinforced Concrete (RC) buildings. 66 RC
buildings with four to ten storeys were subjected to performance
analysis according to the parameters which are the existing material,
loading and geometrical characteristics of the buildings. The selected
parameters have been thought to be effective on the performance of
RC buildings. In the performance analyses stage of the study, level of
performance possible to be shown by these buildings in case of an
earthquake was determined on the basis of the 4-grade performance
levels specified in Turkish Earthquake Code-2007 (TEC-2007). After
obtaining the 4-grade performance level, selected 23 parameters of
each building have been matched with the performance level. In this
stage, ANN-based fast evaluation algorithm mentioned above made
an economic and rapid evaluation of four to ten storey RC buildings.
According to the study, the prediction accuracy of ANN has been
found about 74%.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: This paper presents the experimental investigation on
the bond behavior of geo polymer concrete. The bond behavior of
geo polymer concrete cubes of grade M35 reinforced with 16 mm
TMT rod is analyzed. The results indicate that the bond performance
of reinforced geo polymer concrete is good and thus proves its
application for construction.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: It is a major challenge to build a bridge superstructure
that has long-term durability and low maintenance requirements. A
solution to this challenge may be to use new materials or to
implement new structural systems. Fiber Reinforced Polymer (FRP)
composites have continued to play an important role in solving some
of persistent problems in infrastructure applications because of its
high specific strength, light weight, and durability. In this study, the
concept of the hybrid FRP-concrete structural systems is applied to a
bridge superstructure. The hybrid FRP-concrete bridge superstructure
is intended to have durable, structurally sound, and cost effective
hybrid system that will take full advantage of the inherent properties
of both FRP materials and concrete. In this study, two hybrid FRP-concrete
bridge systems were investigated. The first system consists
of trapezoidal cell units forming a bridge superstructure. The second
one is formed by arch cells. The two systems rely on using cellular
components to form the core of the bridge superstructure, and an
outer shell to warp around those cells to form the integral unit of the
bridge. Both systems were investigated analytically by using finite
element (FE) analysis. From the rigorous FE studies, it was
concluded that first system is more efficient than the second.
Abstract: White concrete facade elements are widely used in
construction industry. It is challenging to achieve the desired
workability in casting of white concrete elements. Particle Matrix
model was used for proportioning the self-compacting white concrete
(SCWC) to control segregation and bleeding and to improve
workability. The paper presents how to reach the target slump flow
while controlling bleeding and segregation in SCWC. The amount of
aggregates, binders and mixing water, as well as type and dosage of
superplasticizer (SP) to be used are the major factors influencing the
properties of SCWC. Slump flow and compressive strength tests were
carried out to examine the performance of SCWC, and the results
indicate that the particle matrix model could produce successfully
SCWC controlling segregation and bleeding.
Abstract: This paper is aimed to the use of different types of
industrial wastes in concrete production. From examined waste
(crushed concrete waste) our tested concrete samples with dimension
150 mm were prepared. In these samples, fractions 4/8 mm and 8/16
mm by recycled concrete aggregate with a range of variation from 0
to 100% were replaced. Experiment samples were tested for
compressive strength after 2, 7, 14 and 28 days of hardening.
From obtained results it is evident that all samples prepared with
washed recycled concrete aggregates met the requirement of standard
for compressive strength of 20 MPa already after 14 days of
hardening. Sample prepared with recycled concrete aggregates (4/8
mm: 100% and 8/16 mm: 60%) reached 101% of compressive
strength value (34.7 MPa) after 28 days of hardening in comparison
with the reference sample (34.4 MPa). The lowest strength after 28
days of hardening (27.42 MPa) was obtained for sample consisting of
recycled concrete in proportion of 40% for 4/8 fraction and 100% for
8/16 fraction of recycled concrete.
Abstract: A large amount of blast furnace slag is generated in
China. Most ground granulated blast furnace slag (GGBS) however
ends up in low-grade applications. Blast furnace slag, ground to an
appropriate fineness, can be used as a partial replacement of
cementitious material in concrete. The potential for using GGBS in
structural concrete, e.g. concrete beams and columns is investigated
at Xi’an Jiaotong-Liverpool University (XJTLU). With 50% of CEM
I cement replaced with GGBS, peak hydration temperatures
determined in a suspended concrete slab reduced by 20%. This
beneficiary effect has not been further improved with 70% of CEM I
replaced with GGBS. Partial replacement of CEM I with GGBS has a
retardation effect on the early-age strength of concrete. More GGBS
concrete mixes will be conducted to identify an ‘optimum’
replacement level which will lead to a reduced thermal loading,
without significantly compromising the early-age strength of
concrete.
Abstract: Air-cooled Blast Furnace Slag Aggregate (BFSA) is
usually referred to as a material providing for unique properties of
concrete. On the other hand, negative influences are also presented in
many aspects. The freeze-thaw resistance of concrete is dependent on
many factors, including regional specifics and when a concrete mix is
specified it is still difficult to tell its exact freeze-thaw resistance due
to the different components affecting it. An important consideration
in working with BFSA is the granularity and whether slag is sorted or
not. The experimental part of the article represents a comparative
testing of concrete using both the sorted and unsorted BFSA through
the freeze-thaw resistance as an indicator of durability. Unsorted
BFSA is able to be successfully used for concretes as they are
specified for exposure class XF4 with providing that the type of
cement is precisely selected.
Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.
Abstract: The composite pavement system considered in this
paper is composed of a functional surface layer, a fiber reinforced
asphalt middle layer and a fiber reinforced lean concrete base layer.
The mix design of the fiber reinforced lean concrete corresponds to the
mix composition of conventional lean concrete but reinforced by
fibers. The quasi-absence of research on the durability or long-term
performances (fatigue, creep, etc.) of such mix design stresses the
necessity to evaluate experimentally the long-term characteristics of
this layer composition. This study tests the creep characteristics as one
of the long-term characteristics of the fiber reinforced lean concrete
layer for composite pavement using a new creep device. The test
results reveal that the lean concrete mixed with fiber reinforcement
and fly ash develops smaller creep than the conventional lean
concrete. The results of the application of the CEB-FIP prediction
equation indicate that a modified creep prediction equation should be
developed to fit with the new mix design of the layer.
Abstract: In this paper, the author studied the possibilities of
using Rice Husk Ash (RHA) available in India; to produce concrete.
Experiments conducted with RHA obtained from West Bengal, India;
to replace cement partially to produce concrete of grade M10, M15,
M20, M25 and M30. The concrete produced in the laboratory by
replacing cement by 5%, 10%, 15%, 20%, 25% and 30% RHA.
Compressive strength tests carried out to determine the strength of
concrete. Cost analysis and comparison done to show the cost
effectiveness of RHA Concrete. Traditional uses of Rice Husk in
India pointed out and the advantages of using RHA in making
concrete highlighted. Suggestion provided regarding prospective
application of RHA concrete in India; which in turn will definitely
reduce the cost of concrete and environmental friendly due to
utilization of waste and replacement of Cement.
Abstract: Cement concrete is a complex mixture of different
materials. Behaviour of concrete depends on its mix proportions and
constituents when it is subjected to elevated temperatures. Principal
effects due to elevated temperatures are loss in compressive strength,
loss in weight or mass, change in colour and spall of concrete. The
experimental results of normal concrete and high strength concrete
subjected elevated temperatures at 200°C, 400°C, 600°C, and 800°C
and different cooling regimes viz. air cooling, water quenching on
different grade of concrete are reported in this paper.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: The main objective of this paper is study the influence
of carbon nano-tubes fibers and nano silica fibers on the
characteristic compressive strength and flexural strength on concrete
and cement mortar. Twelve tested specimens were tested with square
section its dimensions (4040 160) mm, divided into four groups.
The first and second group studied the effect of carbon nano-tubes
(CNTs) fibers with different percentage equal to 0.0, 0.11%, 0.22%,
and 0.33% by weight of cement and effect of nano-silica (nS) fibers
with different percentages equal to 0.0, 1.0%, 2.0%, and 3.0% by
weight of cement on the cement mortar. The third and fourth groups
studied the effect of CNTs fiber with different percentage equal to
0.0%, 0.11%, and 0.22% by weight of cement, and effect of nS fibers
with different percentages were equal to 0.0%, 1.0%, and 2.0% by
weight of cement on the concrete. The compressive strength and
flexural strength at 7, 28, and 90 days is determined. From analysis of
tested results concluded that the nano-fibers is more effective when
used with cement mortar more than used with concrete because of
increasing the surface area, decreasing the pore and the collection of
nano-fibers. And also by adding nano-fibers the improvement of
flexural strength of concrete and cement mortar is more than
improvement of compressive strength.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: The purpose of this study is to compare Self
Compacting Concrete (SCC) and Conventional Concrete (CC) in
terms of their capillary water absorption. During the comparison of
SCC and CC, the effects of two different factors were also
investigated: concrete strength class and curing condition. In the
study, both SCC and CC were produced in three different concrete
classes (C25, C50 and C70) and the other parameter (i.e. curing
condition) was determined as two levels: moisture and air curing. It
was observed that, for both curing environments and all strength
classes of concrete, SCCs had lower capillary water absorption values
than that of CCs. It was also detected that, for both SCC and CC,
capillary water absorption values of samples kept in moisture curing
were significantly lower than that of samples stored in air curing.
Additionally, it was determined that capillary water absorption values
for both SCC and CC decrease with increasing strength class of
concrete for both curing environments.
Abstract: This paper is concerning the issues of behaviour of
lightweight expanded clay aggregates concrete exposed to high
temperature. Lightweight aggregates from expanded clay are
produced by firing of row material up to temperature 1050°C.
Lightweight aggregates have suitable properties in terms of volume
stability, when exposed to temperatures up to 1050°C, which could
indicate their suitability for construction applications with higher risk
of fire. The test samples were exposed to heat by using the standard
temperature-time curve ISO 834. Negative changes in resulting
mechanical properties, such as compressive strength, tensile strength,
and flexural strength were evaluated. Also visual evaluation of the
specimen was performed. On specimen exposed to excessive heat, an
explosive spalling could be observed, due to evaporation of
considerable amount of unbounded water from the inner structure of
the concrete.
Abstract: This paper focuses on the presentation of results
which were obtained as a part of the project FR-TI 3/742: “System of
Lightweight Materials for Finishing of Buildings with Waste Raw
Materials”. Attention was paid to the light weighting of polymermodified
mortars applicable as adhesives, screeds and repair mortars.
In terms of repair mortars, they were ones intended for the sanitation
of aerated concrete.