Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: One of the tasks of optical surveillance is to detect
anomalies in large amounts of image data. However, if the size of the
anomaly is very small, limited information is available to distinguish
it from the surrounding environment. Spectral detection provides a
useful source of additional information and may help to detect
anomalies with a size of a few pixels or less. Unfortunately, spectral
cameras are expensive because of the difficulty of separating two
spatial in addition to one spectral dimension. We investigate the
possibility of modifying a simple spectral line detector for outdoor
detection. This may be especially useful if the area of interest forms a
line, such as the horizon. We use a monochrome CCD that also
enables detection into the near infrared. A simple camera is attached
to the setup to determine which part of the environment is spectrally
imaged. Our preliminary results indicate that sensitive detection of
very small targets is indeed possible. Spectra could be taken from the
various targets by averaging columns in the line image. By imaging a
set of lines of various widths we found narrow lines that could not be
seen in the color image but remained visible in the spectral line
image. A simultaneous analysis of the entire spectra can produce
better results than visual inspection of the line spectral image. We are
presently developing calibration targets for spatial and spectral
focusing and alignment with the spatial camera. This will present
improved results and more use in outdoor application.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: This paper introduces the concept and principle of data
cleaning, analyzes the types and causes of dirty data, and proposes
several key steps of typical cleaning process, puts forward a well
scalability and versatility data cleaning framework, in view of data
with attribute dependency relation, designs several of violation data
discovery algorithms by formal formula, which can obtain inconsistent
data to all target columns with condition attribute dependent no matter
data is structured (SQL) or unstructured (NoSql), and gives 6 data
cleaning methods based on these algorithms.
Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.
Abstract: Nowadays, energy dissipation devices are commonly
used in structures. High rate of energy absorption during earthquakes
is the benefit of using such devices, which results in damage
reduction of structural elements, specifically columns. The hysteretic
damping capacity of energy dissipation devices is the key point that it
may adversely make analysis and design process complicated. This
effect may be generally represented by Equivalent Viscous Damping
(EVD). The equivalent viscous damping might be obtained from the
expected hysteretic behavior regarding to the design or maximum
considered displacement of a structure. In this paper, the hysteretic
damping coefficient of a steel Moment Resisting Frame (MRF),
which its performance is enhanced by a Buckling Restrained Brace
(BRB) system has been evaluated. Having foresight of damping
fraction between BRB and MRF is inevitable for seismic design
procedures like Direct Displacement-Based Design (DDBD) method.
This paper presents an approach to calculate the damping fraction for
such systems by carrying out the dynamic nonlinear time history
analysis (NTHA) under harmonic loading, which is tuned to the
natural system frequency. Two MRF structures, one equipped with
BRB and the other without BRB are simultaneously studied.
Extensive analysis shows that proportion of each system damping
fraction may be calculated by its shear story portion. In this way,
contribution of each BRB in the floors and their general contribution
in the structural performance may be clearly recognized, in advance.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear dynamics
analysis of the structures with assuming elastic-perfectly-plastic
behavior was performed using RAM PERFORM-3D software; the
horizontal component was taken into consideration with and without
the incorporation of the corresponding vertical component. Dynamic
responses obtained for the horizontal component acting alone were
compared with those obtained from the simultaneous application of
both seismic components. The results show that the effect of the
vertical component of ground motion may increase the axial load
significantly in the interior columns and, consequently, the stories.
The plastic mechanisms would be changed. The P-Delta effect is
expected to increase. The punching base plate shear of the columns
should be considered. Moreover, the vertical component increases the
input energy when the structures exhibit inelastic behavior and are
taller.
Abstract: By enhancing the applicatıon of grounds for
establishment and due to the lack of appropriate sites, engineers
attempt to seek out a new method to reduce the weakness of soils. İn
aspect of economic situation, various ways have been used to
decrease the weak grounds. Because of the rapid development of
infrastructural facilities, spreading the construction operation is an
obligation. Furthermore, in various sites with the really bad soil
situation, engineers have considered obvious problems. One of the
most essential ways for developing the weak soils is stone column.
Obviously, the method was introduced in France in 1830 to improve
a native soil initially. Stone columns have an expanding range of
usage in different rough foundation sites all over the world to
increase the bearing capacity, to reduce the whole and differential
settlements, to enhance the rate of consolidation, to stabilize slopes
stability of embankments and to increase the liquefaction resistance
as well. A recent procedure called installing vertical nails along the
round stone columns in order to make better the performance of
considered columns is offered. Moreover, thanks to the enhancing the
nail diameter, number and embedment nail depth, the positive points
of vertical circumferential nails increases. Based on the result of this
study, load caring capacity will be develop with enhancing the length
and the power of reinforcements in vertical encasement stone column
(CESC). In this study, the main purpose is comparing two methods of
stone columns (installed a nail surrounding the stone columns and
using geogrid on clay) for enhancing the bearing capacity, decreasing
the whole and various settlements.
Abstract: A flow column has been innovatively used in the
design of a new electrocoagulation reactor (ECR1) that will reduce
the temperature of water being treated; where the flow columns work
as a radiator for the water being treated. In order to investigate the
performance of ECR1 and compare it to that of traditional reactors;
600 mL water samples with an initial temperature of 350C were
pumped continuously through these reactors for 30 min at current
density of 1 mA/cm2. The temperature of water being treated was
measured at 5 minutes intervals over a 30 minutes period using a
thermometer. Additional experiments were commenced to investigate
the effects of initial temperature (15-350C), water conductivity (0.15
– 1.2 S) and current density (0.5 -3 mA/cm2) on the performance of
ECR1.
The results obtained demonstrated that the ECR1, at a current
density of 1 mA/cm2 and continuous flow model, reduced water
temperature from 350C to the vicinity of 280C during the first 15
minutes and kept the same level till the end of the treatment time.
While, the temperature increased from 28.1 to 29.80C and from 29.8
to 31.90C in the batch and the traditional continuous flow models
respectively. In term of initial temperature, ECR1 maintained the
temperature of water being treated within the range of 22 to 280C
without the need for external cooling system even when the initial
temperatures varied over a wide range (15 to 350C). The influent
water conductivity was found to be a significant variable that affect
the temperature. The desirable value of water conductivity is 0.6 S.
However, it was found that the water temperature increased rapidly
with a higher current density.
Abstract: In the Hierarchical Temporal Memory (HTM) paradigm
the effect of overlap between inputs on the activation of columns in
the spatial pooler is studied. Numerical results suggest that similar
inputs are represented by similar sets of columns and dissimilar inputs
are represented by dissimilar sets of columns. It is shown that the
spatial pooler produces these results under certain conditions for
the connectivity and proximal thresholds. Following the discussion
of the initialization of parameters for the thresholds, corresponding
qualitative arguments about the learning dynamics of the spatial
pooler are discussed.
Abstract: This study investigated the behavior of improved soft soils through the vibro replacement technique by considering their settlements and consolidation rates and the applicability of this technique in various types of soils and settlement and bearing capacity calculations.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: Reflux condensation occurs in vertical channels and tubes when there is an upward core flow of vapour (or gas-vapour mixture) and a downward flow of the liquid film. The understanding of this condensation configuration is crucial in the design of reflux condensers, distillation columns, and in loss-of-coolant safety analyses in nuclear power plant steam generators. The unique feature of this flow is the upward flow of the vapour-gas mixture (or pure vapour) that retards the liquid flow via shear at the liquid-mixture interface. The present model solves the full, elliptic governing equations in both the film and the gas-vapour core flow. The computational mesh is non-orthogonal and adapts dynamically the phase interface, thus produces a sharp and accurate interface. Shear forces and heat and mass transfer at the interface are accounted for fundamentally. This modeling is a big step ahead of current capabilities by removing the limitations of previous reflux condensation models which inherently cannot account for the detailed local balances of shear, mass, and heat transfer at the interface. Discretisation has been done based on finite volume method and co-located variable storage scheme. An in-house computer code was developed to implement the numerical solution scheme. Detailed results are presented for laminar reflux condensation from steam-air mixtures flowing in vertical parallel plate channels. The results include velocity and gas mass fraction profiles, as well as axial variations of film thickness.
Abstract: A large amount of blast furnace slag is generated in
China. Most ground granulated blast furnace slag (GGBS) however
ends up in low-grade applications. Blast furnace slag, ground to an
appropriate fineness, can be used as a partial replacement of
cementitious material in concrete. The potential for using GGBS in
structural concrete, e.g. concrete beams and columns is investigated
at Xi’an Jiaotong-Liverpool University (XJTLU). With 50% of CEM
I cement replaced with GGBS, peak hydration temperatures
determined in a suspended concrete slab reduced by 20%. This
beneficiary effect has not been further improved with 70% of CEM I
replaced with GGBS. Partial replacement of CEM I with GGBS has a
retardation effect on the early-age strength of concrete. More GGBS
concrete mixes will be conducted to identify an ‘optimum’
replacement level which will lead to a reduced thermal loading,
without significantly compromising the early-age strength of
concrete.
Abstract: This paper presents experimental investigation and
finite element analysis on buckling behavior of irregular section coldformed
steel columns under axially concentric loading. For the
experimental study, four different sections of columns were tested to
investigate effect of stiffening and width-to-thickness ratio on
buckling behavior. For each of the section, three lengths of 230, 950
and 1900 mm. were studied representing short, intermediate long and
long columns, respectively. Then, nonlinear finite element analyses
of the tested columns were performed. The comparisons in terms of
load-deformation response and buckling mode show good agreement
and hence the FEM models were validated. Parametric study of
stiffening element and thickness of 1.0, 1.15, 1.2, 1.5, 1.6 and 2.0
mm. was analyzed. The test results showed that stiffening effect pays
a large contribution to prevent distortional mode. The increase in wall
thickness enhanced buckling stress beyond the yielding strength in
short and intermediate columns, but not for the long columns.
Abstract: An experimental study was performed to investigate
the behavior and strength of proposed technique to connect
reinforced concrete (RC) beam to steel or composite columns. This
approach can practically be used in several types of building
construction. In this technique, the main beam of the frame consists
of a transfer part (part of beam; Tr.P) and a common reinforcement
concrete beam. The transfer part of the beam is connected to the
column, whereas the rest of the beam is connected to the transfer part
from each side. Four full-scale beam-column connections were tested
under static loading. The test parameters were the length of the
transfer part and the column properties. The test results show that
using of the transfer part technique leads to modify the deformation
capabilities for the RC beam and hence it increases its resistance
against failure. Increase in length of the transfer part did not
necessarily indicate an enhanced behavior. The test results contribute
to the characterization of the connection behavior between RC beam -
steel column and can be used to calibrate numerical models for the
simulation of this type of connection.
Abstract: The seismic responses of steel buildings with semirigid
post-tensioned connections (PC) are estimated and compared
with those of steel buildings with typical rigid (welded) connections
(RC). The comparison is made in terms of global and local response
parameters. The results indicate that the seismic responses in terms of
interstory shears, roof displacements, axial load and bending
moments are smaller for the buildings with PC connection. The
difference is larger for global than for local parameters, which in turn
varies from one column location to another. The reason for this
improved behavior is that the buildings with PC dissipate more
hysteretic energy than those with RC. In addition, unlike the case of
buildings with WC, for the PC structures the hysteretic energy is
mostly dissipated at the connections, which implies that structural
damage in beams and columns is not significant. According to these
results, steel buildings with PC are a viable option in high seismicity
areas because of their smaller response and self-centering connection
capacity as well as the fact that brittle failure is avoided.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: This paper investigates the viability of using carbon
fiber reinforced epoxy composites modified with carbon nanotubes to
strengthening reinforced concrete (RC) columns. Six RC columns
was designed and constructed according to ASCE standards. The
columns were wrapped using carbon fiber sheets impregnated with
either neat epoxy or CNTs modified epoxy. These columns were then
tested under concentric axial loading. Test results show that;
compared to the unwrapped specimens; wrapping concrete columns
with carbon fiber sheet embedded in CNTs modified epoxy resulted
in an increase in its axial load resistance, maximum displacement,
and toughness values by 24%, 109% and 232%, respectively. These
results reveal that adding CNTs into epoxy resin enhanced the
confinement effect, specifically, increased the axial load resistance,
maximum displacement, and toughness values by 11%, 6%, and
19%, respectively compared with columns strengthening with carbon
fiber sheet embedded in neat epoxy.
Abstract: Columns have traditionally been constructed of
reinforced concrete or structural steel. Much attention was allocated
to estimate the axial capacity of the traditional column sections to the
detriment of other forms of construction. Other forms of column
construction such as Concrete Filled Double Skin Tubes received
little research attention, and almost no attention when subjected to
eccentric loading. This paper investigates the axial capacity of
columns when subjected to eccentric loading. The experimental axial
capacities are compared to other established theoretical formulae on
concentric loading to determine a possible relationship. The study
found a good correlation between the reduction in axial capacity for
different column lengths and hollow section ratios.