Abstract: In the urban traffic network, the intersections are the
“bottleneck point" of road network capacity. And the arterials are the
main body in road network and the key factor which guarantees the
normal operation of the city-s social and economic activities. The
rapid increase in vehicles leads to seriously traffic jam and cause the
increment of vehicles- delay. Most cities of our country are
traditional single control system, which cannot meet the need for the
city traffic any longer. In this paper, Synchro6.0 as a platform to
minimize the intersection delay, optimizesingle signal cycle and split
for Zhonghua Street in Handan City. Meanwhile, linear control
system uses to optimize the phase for the t arterial road in this
system. Comparing before and after use the control, capacities and
service levels of this road and the adjacent road have improved
significantly.
Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: Most of the real queuing systems include special properties and constraints, which can not be analyzed directly by using the results of solved classical queuing models. Lack of Markov chains features, unexponential patterns and service constraints, are the mentioned conditions. This paper represents an applied general algorithm for analysis and optimizing the queuing systems. The algorithm stages are described through a real case study. It is consisted of an almost completed non-Markov system with limited number of customers and capacities as well as lots of common exception of real queuing networks. Simulation is used for optimizing this system. So introduced stages over the following article include primary modeling, determining queuing system kinds, index defining, statistical analysis and goodness of fit test, validation of model and optimizing methods of system with simulation.
Abstract: The presence of a vertical fatigue crack in the web of
a plate girder subjected to pure bending influences the bending
moment capacity of the girder. The growth of the crack may lead to
premature elastic failure due to flange local yielding, flange local
buckling, or web local buckling. Approximate expressions for the
bending moment capacities corresponding to these failure modes
were formulated. Finite element analyses were then used to validate
the expressions. The expressions were employed to assess the effects
of crack length on the capacity. Neglecting brittle fracture, tension
buckling, and ductile failure modes, it was found that typical girders
are governed by the capacity associated with flange local yielding as
influenced by the crack. Concluding, a possible use of the capacity
expressions in girder design was demonstrated.
Abstract: The deficit of power for electricity demand reaches
almost 30% for consumers in the last few years. This reflects with
continually increasing the price of electricity, and today the price for
small industry is almost 110Euro/MWh. The high price is additional
problem for the owners in the economy crisis which is reflected with
higher price of the goods.
The paper gives analyses of the energy needs for real agro
complex in Macedonia, private vinery with capacity of over 2 million
liters in a year and with self grapes and fruits fields. The existing
power supply is from grid with 10/04 kV transformer. The
geographical and meteorological condition of the vinery location
gives opportunity for including renewable as a power supply option
for the vinery complex.
After observation of the monthly energy needs for the vinery, the
base scenario is the existing power supply from the distribution grid.
The electricity bill in small industry has three factors: electricity in
high and low tariffs in kWh and the power engaged for the
technological process of production in kW. These three factors make
the total electricity bill and it is over 110 Euro/MWh which is the
price near competitive for renewable option. On the other side
investments in renewable (especially photovoltaic (PV)) has tendency
of decreasing with price of near 1,5 Euro/W. This means that
renewable with PV can be real option for power supply for small
industry capacities (under 500kW installed power).
Therefore, the other scenarios give the option with PV and the last
one includes wind option. The paper presents some scenarios for
power supply of the vinery as the followings:
• Base scenario of existing conventional power supply from the
grid
• Scenario with implementation of renewable of Photovoltaic
• Scenario with implementation of renewable of Photovoltaic and
Wind power
The total power installed in a vinery is near 570 kW, but the
maximum needs are around 250kW. At the end of the full paper some
of the results from scenarios will be presented. The paper also
includes the environmental impacts of the renewable scenarios, as
well as financial needs for investments and revenues from renewable.
Abstract: Ciprofloxacin (CIP) and Carbamazepine (CBZ), nonbiodegradable pharmaceutical residues, were become emerging pollutants in several aquatic environments. The objectives of this research were to study the possibility to recover these pharmaceuticals residues from pharmaceutical wastewater by increasing the selective adsorption on synthesized functionalized porous silicate, comparing with powdered activated carbon (PAC). Hexagonal mesoporous silicate (HMS), functionalized HMSs (3- aminopropyltriethoxy, 3- mercaptopropyltrimethoxy and noctyldimethyl) were synthesized and characterized physico-chemical characteristics. Obtained adsorption kinetics and isotherms showed that 3-mercaptopropyltrimethoxy functional groups grafted on HMS provided highest CIP and CBZ adsorption capacities; however, it was still lower than that of PAC. The kinetic results were compatible with pseudo-second order. The hydrophobicity and hydrogen bonding might play a key role on the adsorption. Furthermore, the capacities were affected by varying pH values due to the strength of hydrogen bonding between targeted compounds and adsorbents. Electrostatic interaction might not affect the adsorption capacities.
Abstract: Cassava is one of the top five crops in Cameroon. Its
evolution has remained constant since the independence period and
the production has more than tripled. It is a crop with multiple
industrial capacities but the sector-s business opportunities are
underexploited. Using Strengths, Weaknesses, Opportunities and
Threats analysis method, this paper examines the cassava actual state.
It appraises the sector-s strengths (S), considers suitable measures to
strengthen weaknesses (W), evaluates strategies to fully benefit from
the sector numerous business opportunities (O) and explore means to
convert threats (T) into opportunities. Data were collected from the
ministry of agriculture and rural development and different actors.
The results show that cassava sector embodies many business
opportunities and stands as a raw material provider for many
industries but ultimately requires challenges to be tackled
appropriately.
Abstract: The restoration of extinct ponds is considered as one
of ways to gain new retention capacities for water which is getting
much more important issue with respect to expected impacts of a
climate change. However, there are also other pressures on the
landscape which must be all taken into consideration when making a
decision on the possible restoration of extinct ponds. The research
presented here focuses besides others on the restoration of former
ponds which could be important for both the flood protection and
drought impacts prevention. The first step of the methodology
development for the assessment of such areas is the assessment of
their present state. In this paper, the results of land use types
assessment for 22 localities are presented. These results confirm the
assumption that the most present land use type in such areas is the
permanent grassland. However, the spectra of land use types present
in extinct pond areas is very diverse and include besides others also
airport areas and industry.
Abstract: The efficiency of chitosan beads processed from 4
marine animal shells; white leg shrimp (Litopenaeus vannamei), mud
crab (Scylla sp.), horseshoe crab (Carcinoscorpius rotundicauda),
and cuttlefish bone (Sepia sp.), for the adsorption experiments of
ammonia and formaldehyde were investigated. The porosities of
chitosan from the shells looked like beads were distinctly examined
under SEM. The original pores of those shells on the surface areas
compose of evenly fine pores. The shell beads of cuttlefish bone and
horseshoe crab show the larger probably even porosity, while on
those white leg shrimp and mud crab contain various large and fine
pores. The best adsorption at pH 9 in 18 mg/l ammonia at 2 hours
yield on cuttlefish bone, horseshoe crab, mud crab and white leg
shrimp with the average percent of 59.12, 51.45, 45.66 and 43.52,
respectively. Within 30 minutes the formaldehyde absorbers (at pH 5
in 8 μg/ml) revealed 46.27, 26.56, and 18.04 percent capacities in
cuttlefish bone, mud crab and white leg shrimp beads; while 22.44
percent in the horseshoe crab at pH 7. The adsorption capacities and
the amounts of beads showed a positive correlation. The adsorption
capacity relationship between pH and the gas concentrations were
affected by these qualities of chitosan beads.
Abstract: The objective of this research is to investigate the
advantages of using large-diameter 0.7 inch prestressing strands in
pretention applications. The advantages of large-diameter strands are
mainly beneficial in the heavy construction applications. Bridges and
tunnels are subjected to a higher daily traffic with an exponential
increase in trucks ultimate weight, which raise the demand for higher
structural capacity of bridges and tunnels. In this research, precast
prestressed I-girders were considered as a case study. Flexure
capacities of girders fabricated using 0.7 inch strands and different
concrete strengths were calculated and compared to capacities of 0.6
inch strands girders fabricated using equivalent concrete strength.
The effect of bridge deck concrete strength on composite deck-girder
section capacity was investigated due to its possible effect on final
section capacity. Finally, a comparison was made to compare the
bridge cross-section of girders designed using regular 0.6 inch strands
and the large-diameter 0.7 inch. The research findings showed that
structural advantages of 0.7 inch strands allow for using fewer bridge
girders, reduced material quantity, and light-weight members. The
structural advantages of 0.7 inch strands are maximized when high
strength concrete (HSC) are used in girder fabrication, and concrete
of minimum 5ksi compressive strength is used in pouring bridge
decks. The use of 0.7 inch strands in bridge industry can partially
contribute to the improvement of bridge conditions, minimize
construction cost, and reduce the construction duration of the project.
Abstract: The National Bridge Inventory (NBI) includes more
than 600,000 bridges within the United States of America.
Prestressed concrete girder bridges represent one of the most widely
used bridge systems. The majority of these girder bridges were
constructed using 0.5 and 0.6 inch diameter strands. The main
impediments to using larger strand diameters are: 1) lack of prestress
bed capacities, 2) lack of structural knowledge regarding the transfer
and development length of larger strands, and 3) the possibility of
developing wider end zone cracks upon strand release.
This paper presents a study about using 0.7 inch strands in girder
fabrication. Transfer and development length were evaluated, and
girders were fabricated using 0.7 inch strands at different spacings.
Results showed that 0.7 inch strands can be used at 2.0 inch spacing
without violating the AASHTO LRFD Specifications, while attaining
superior performance in shear and flexure.
Abstract: The fortified of soft wheat flour with cowpea flour in
bread making was investigated. The Soft wheat flour (SWF) was
substituted by cowpea flour at levels of 5, 15 and 20%. The protein content of composite breads ranged from 6.1 – 9.9%. Significant
difference was observed in moisture, protein and crude fibre contents of control (wheat bread) and composite bread at 5% addition of
cowpea. Water absorption capacities of composite flours increased with increasing levels of cowpea flour in the blend. The specific loaf
volume decreased significantly with increased cowpea content of
blends. The overall acceptability of the 5% cowpea flour content of
composite bread was not significantly different from the control (Soft Wheat-bread) but there is significantly different with increasing the
levels of cowpea flour in the blend more than 5%.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: There are only limited studies that directly correlate
the increase in reinforced concrete (RC) panel structural capacities in
resisting the blast loads with different RC panel structural properties
in terms of blast loading characteristics, RC panel dimensions, steel
reinforcement ratio and concrete material strength. In this paper,
numerical analyses of dynamic response and damage of the one-way
RC panel to blast loads are carried out using the commercial software
LS-DYNA. A series of simulations are performed to predict the blast
response and damage of columns with different level and magnitude
of blast loads. The numerical results are used to develop pressureimpulse
(P-I) diagrams of one-way RC panels. Based on the
numerical results, the empirical formulae are derived to calculate the
pressure and impulse asymptotes of the P-I diagrams of RC panels.
The results presented in this paper can be used to construct P-I
diagrams of RC panels with different concrete and reinforcement
properties. The P-I diagrams are very useful to assess panel capacities
in resisting different blast loads.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images and set up compression-transmit schemes to distribute result to the remote doctor. To achieve this goal, we use basically a level-sets approach to delineating brain tumors in threedimensional. Then introduce a new compression and transmission plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by wireless network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: Focusing on the environmental issues, including the reduction of scrap and consumer residuals, along with the benefiting from the economic value during the life cycle of goods/products leads the companies to have an important competitive approach. The aim of this paper is to present a new mixed nonlinear facility locationallocation model in recycling collection networks by considering multi-echelon, multi-suppliers, multi-collection centers and multifacilities in the recycling network. To make an appropriate decision in reality, demands, returns, capacities, costs and distances, are regarded uncertain in our model. For this purpose, a fuzzy mathematical programming-based possibilistic approach is introduced as a solution methodology from the recent literature to solve the proposed mixed-nonlinear programming model (MNLP). The computational experiments are provided to illustrate the applicability of the designed model in a supply chain environment and to help the decision makers to facilitate their analysis.
Abstract: In a recent major industry-supported research and development study, a novel framework was developed and applied for assessment of reliability and quality performance levels in reallife power systems with practical large-scale sizes. The new assessment methodology is based on three metaphors (dimensions) representing the relationship between available generation capacities and required demand levels. The paper shares the results of the successfully completed stud and describes the implementation of the new methodology on practical zones in the Saudi electricity system.
Abstract: Rapid enlargement and physical development of cities
have facilitated the emergence of a number of city life crises and
decrease of environment quality. Subsequently, the need for noticing
the concept of quality and its improvement in urban environments,
besides quantitative issues, is obviously recognized. In the domain of
urban ideas the importance of taking these issues into consideration
is obvious not only in accordance to sustainable development
concepts and improvement of public environment quality, but also in
the enhancement of social and behavioral models.
The major concern of present article is to study the nature of urban
environment quality in urban development plans, which is important
not only in the concept and the aim of projects but also in their
execution procedure. As a result, this paper is going to utilize
planning capacities caused by environmental virtues in the planning
procedure of Moft Abad neighborhood. Thus, at the first step,
applying the Analytical Hierarchy Process (AHP), it has assessed
quantitative environmental issues. The present conditions of Moft
Abad state that “the neighborhood is generally suffering from the
lack of qualitative parameters, and the previously formed planning
procedures could not take the sustainable and developmental paths
which are aimed at environment quality virtues." The diminution of
economical and environmental virtues has resulted in the diminution
of residential and social virtues. Therefore, in order to enhance the
environment quality in Moft Abad, the present paper has tried to
supply the subject plans in order to make a safe, healthy, and lively
neighborhood.