Abstract: This paper presents parametric probability density
models for call holding times (CHTs) into emergency call center
based on the actual data collected for over a week in the public
Emergency Information Network (EIN) in Mongolia. When the set of
chosen candidates of Gamma distribution family is fitted to the call
holding time data, it is observed that the whole area in the CHT
empirical histogram is underestimated due to spikes of higher
probability and long tails of lower probability in the histogram.
Therefore, we provide the Gaussian parametric model of a mixture of
lognormal distributions with explicit analytical expressions for the
modeling of CHTs of PSNs. Finally, we show that the CHTs for
PSNs are fitted reasonably by a mixture of lognormal distributions
via the simulation of expectation maximization algorithm. This result
is significant as it expresses a useful mathematical tool in an explicit
manner of a mixture of lognormal distributions.
Abstract: In this paper, collocation based cubic B-spline and
extended cubic uniform B-spline method are considered for
solving one-dimensional heat equation with a nonlocal initial
condition. Finite difference and θ-weighted scheme is used for
time and space discretization respectively. The stability of the
method is analyzed by the Von Neumann method. Accuracy of
the methods is illustrated with an example. The numerical results
are obtained and compared with the analytical solutions.
Abstract: This paper presents the identification of the impact
force acting on a simply supported beam. The force identification is
an inverse problem in which the measured response of the structure is
used to determine the applied force. The identification problem is
formulated as an optimization problem and the genetic algorithm is
utilized to solve the optimization problem. The objective function is
calculated on the difference between analytical and measured
responses and the decision variables are the location and magnitude
of the applied force. The results from simulation show the
effectiveness of the approach and its robustness vs. the measurement
noise and sensor location.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: The analytical solution of functionally graded
piezoelectric hollow cylinder which is under radial electric potential
and non-axisymmetric thermo-mechanical loads, are presented in this
paper. Using complex Fourier series and estimation of power law for
variations of material characterizations through the thickness, the
electro thermo mechanical behavior of the FGPM cylinder is
obtained. The stress and displacement distributions and the effect of
electric potential field on the cylinder behavior are also presented and
some applicable results are offered at the end of the paper.
Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: In this paper, we have proposed a low cost optimized solution for the movement of a three-arm manipulator using Genetic Algorithm (GA) and Analytical Hierarchy Process (AHP). A scheme is given for optimizing the movement of robotic arm with the help of Genetic Algorithm so that the minimum energy consumption criteria can be achieved. As compared to Direct Kinematics, Inverse Kinematics evolved two solutions out of which the best-fit solution is selected with the help of Genetic Algorithm and is kept in search space for future use. The Inverse Kinematics, Fitness Value evaluation and Binary Encoding like tasks are simulated and tested. Although, three factors viz. Movement, Friction and Least Settling Time (or Min. Vibration) are used for finding the Fitness Function / Fitness Values, however some more factors can also be considered.
Abstract: An empirical linearly-hyperbolic approximation of the I - V characteristic of a solar cell is presented. This approximation is based on hyperbolic dependence of a current of p-n junctions on voltage for large currents. Such empirical approximation is compared with the early proposed formal linearly-hyperbolic approximation of a solar cell. The expressions defining laws of change of parameters of formal approximation at change of a photo current of family of characteristics are received. It allows simplifying a finding of parameters of approximation on actual curves, to specify their values. Analytical calculation of load regime for linearly - hyperbolic model leads to quadratic equation. Also, this model allows to define soundly a deviation from the maximum power regime and to compare efficiency of regimes of solar cells with different parameters.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: Analytical expression for maximum power transfer
through a transmission line limited by voltage stability has been
formulated using exact representation of transmission line with
ABCD parameters. The expression has been used for plotting PV
curve at different power factors of a radial transmission line.
Limiting values of reactive power have been obtained.
Abstract: Given the motivation of maps impact in enhancing the
perception of the quality of life in a region, this work examines the
use of spatial analytical techniques in exploring the role of space in
shaping human development patterns in Assiut governorate.
Variations of human development index (HDI) of the governorate-s
villages, districts and cities are mapped using geographic information
systems (GIS). Global and local spatial autocorrelation measures are
employed to assess the levels of spatial dependency in the data and to
map clusters of human development. Results show prominent
disparities in HDI between regions of Assiut. Strong patterns of
spatial association were found proving the presence of clusters on the
distribution of HDI. Finally, the study indicates several "hot-spots" in
the governorate to be area of more investigations to explore the
attributes of such levels of human development. This is very
important for accomplishing the development plan of poorest regions
currently adopted in Egypt.
Abstract: The inphase/quadrature (I/Q) amplitude and phase
imbalance effects are studied in coherent optical orthogonal
frequency division multiplexing (CO-OFDM) systems. An analytical
model for the I/Q imbalance is developed and supported by
simulation results. The results indicate that the I/Q imbalance degrades the BER performance considerably.
Abstract: Ultrathin (UTD) and Nanoscale (NSD) SOI-MOSFET devices, sharing a similar W/L but with a channel thickness of 46nm and 1.6nm respectively, were fabricated using a selective “gate recessed” process on the same silicon wafer. The electrical transport characterization at room temperature has shown a large difference between the two kinds of devices and has been interpreted in terms of a huge unexpected series resistance. Electrical characteristics of the Nanoscale device, taken in the linear region, can be analytically derived from the ultrathin device ones. A comparison of the structure and composition of the layers, using advanced techniques such as Focused Ion Beam (FIB) and High Resolution TEM (HRTEM) coupled with Energy Dispersive X-ray Spectroscopy (EDS), contributes an explanation as to the difference of transport between the devices.
Abstract: This paper presents the results of an analytical study
on the seismic response of a Multi-Span-Simply-Supported precast
bridge in Washington State. The bridge was built in the early 1960's
along Interstate 5 and was widened the first time in 1979 and the
second time in 2001. The primary objective of this research project
is to determine the seismic vulnerability of the bridge in order to
develop the required retrofit measure. The seismic vulnerability of
the bridge is evaluated using two seismic evaluation methods
presented in the FHWA Seismic Retrofitting Manual for Highway
Bridges, Method C and Method D2. The results of the seismic
analyses demonstrate that Method C and Method D2 vary markedly
in terms of the information they provide to the bridge designer
regarding the vulnerability of the bridge columns.
Abstract: In this paper, an analytical approach for free vibration
analysis of four edges simply supported rectangular Kirchhoff plates
is presented. The method is based on wave approach. From wave
standpoint vibration propagate, reflect and transmit in a structure.
Firstly, the propagation and reflection matrices for plate with simply
supported boundary condition are derived. Then, these matrices are
combined to provide a concise and systematic approach to free
vibration analysis of a simply supported rectangular Kirchhoff plate.
Subsequently, the eigenvalue problem for free vibration of plates is
formulated and the equation of plate natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: In wireless sensor network (WSN) the use of mobile
sink has been attracting more attention in recent times. Mobile sinks
are more effective means of balancing load, reducing hotspot
problem and elongating network lifetime. The sensor nodes in WSN
have limited power supply, computational capability and storage and
therefore for continuous data delivery reliability becomes high
priority in these networks. In this paper, we propose a Reliable
Energy-efficient Data Dissemination (REDD) scheme for WSNs with
multiple mobile sinks. In this strategy, sink first determines the
location of source and then directly communicates with the source
using geographical forwarding. Every forwarding node (FN) creates a
local zone comprising some sensor nodes that can act as
representative of FN when it fails. Analytical and simulation study
reveals significant improvement in energy conservation and reliable
data delivery in comparison to existing schemes.
Abstract: In this paper, we propose a novel adaptive voltage control strategy for boost converter via Inverse LQ Servo-Control. Our presented strategy is based on an analytical formula of Inverse Linear Quadratic (ILQ) design method, which is not necessary to solve Riccati’s equation directly. The optimal and adaptive controller of the voltage control system is designed. The stability and the robust control are analyzed. Whereas, we can get the analytical solution for the optimal and robust voltage control is achieved through the natural angular velocity within a single parameter and we can change the responses easily via the ILQ control theory. Our method provides effective results as the stable responses and the response times are not drifted even if the condition is changed widely.
Abstract: Rockfall is a kind of irregular geological disaster. Its
destruction time, space and movements are highly random. The impact
force is determined by the way and velocity rocks move. The
movement velocity of a rockfall depends on slope gradient of its
moving paths, height, slope surface roughness and rock shapes. For
effectively mitigate and prevent disasters brought by rockfalls, it is
required to precisely calculate the moving paths of a rockfall so as to
provide the best protective design. This paper applies Colorado
Rockfall Simulation Program (CRSP) as our study tool to discuss the
impact of slope shape and surface roughness on the moving paths of a
single rockfall. The analytical results showed that the slope, m=1:1,
acted as the threshold for rockfall bounce height on a monoclinal slight
slope. When JRC ´╝£ 1.2, movement velocity reduced and bounce
height increased as JCR increased. If slope fixed and JRC increased,
the bounce height of rocks increased gradually with reducing
movement velocity. Therefore, the analysis on the moving paths of
rockfalls with CRSP could simulate bouncing of falling rocks. By
analyzing moving paths, velocity, and bounce height of falling rocks,
we could effectively locate impact points of falling rocks on a slope.
Such analysis can be served as a reference for future disaster
prevention and control.