Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: Drought is one of the most important natural disasters which is probable to occur in all regions with completely different climates and in addition to causing death. It results in many economic losses and social consequences. For this reason. Studying the effects and losses caused by drought which include limitation or shortage of agricultural and drinking water resources. Decreased rainfall and increased evapotranspiration. Limited plant growth and decreased agricultural products. Especially those of dry-farming. Lower levels of surface and ground waters and increased immigrations. Etc. in the country is statistical period (1988-2007) for six stations in Roudbar town were used for statistical analysis and calculating humid and dry years. The dependable rainfall index (DRI) was the main method used in this research. Results showed that during the said statistical period and also during the years 1996-1998 and 2007. more than half of the stations had faced drought. With consideration of the conducted studies. Drawing diagrams and comparing the available data with those of dry and humid years it was found that drought affected agricultural products (e.g.olive) in a way that during the year 1996 1996 drought. Olive groves of Roudbar suffered the greatest damages. Whereupon about 70% of the crops were lost.
Abstract: In recent years, the number of natural disasters in the world has occurred frequently. After a strong earthquake occurs, multiple disasters due to tsunami, strong aftershocks or heavy snow can possible to occur. To prevent a secondary disaster and to save a life, the quick inspection of the damaged building is necessary. This paper investigated on a possibility of post earthquake quick inspection of damaged building by ordinary people which used the European Macro- Seismic Scale 1998 (EMS-98).
Abstract: The migration-environment nexus has gained increased interest from the social research field over the last years. While straightly connected to human security issues, this theme has pervaded through the media to the public sphere. Therefore, it is important to observe how did the discussions over environmentally induced migrations develop from the scientific basis to the media attention, passing through some political voices, and in which ways might these messages be interpreted within the broader public discourses. To achieve this purpose, the analysis of the press entries between 2004 and 2010 in three of the main Portuguese newspapers shall be presented, specially reflecting upon the events, protagonists, topics, geographical attributions and terms/expressions used to define those who migrate due to environmental degradation or disasters.
Abstract: Cost contribution arrangements (CCAs) and Cost
sharing agreements (CCAs) belong to the tools of modern finance
management. Costs spend by associated enterprises on developing
producing or obtaining assets, services or rights (in general -
benefits) are used for tax optimizing too. The main purpose of joint
research and development, producing or obtaining benefits is to
lower these costs as much as possible or to maximize the benefits. In
this article is mentioned the problematic of transfer pricing and arm's
length principle with connection of CCAs, CSAs. Next, there is
mentioned how to settle participation shares of the total cost and
benefits contributions with respect to the OECD Transfer pricing for
MNEs Guidelines and with respect to other significant regulations.
Abstract: Widespread use of asbestos over the last century has left a terrible legacy of lung disease. Doctors knew of the health risks long ago, but almost nothing was done to protect workers and the public. Some aspects of nanotechnology may have risks similar to asbestos.
Abstract: In order to monitor for traffic traversal, sensors can be
deployed to perform collaborative target detection. Such a sensor
network achieves a certain level of detection performance with the
associated costs of deployment and routing protocol. This paper
addresses these two points of sensor deployment and routing algorithm
in the situation where the absolute quantity of sensors or total energy
becomes insufficient. This discussion on the best deployment system
concluded that two kinds of deployments; Normal and Power law
distributions, show 6 and 3 times longer than Random distribution in
the duration of coverage, respectively. The other discussion on routing
algorithm to achieve good performance in each deployment system
was also addressed. This discussion concluded that, in place of the
traditional algorithm, a new algorithm can extend the time of coverage
duration by 4 times in a Normal distribution, and in the circumstance
where every deployed sensor operates as a binary model.
Abstract: Topics Disaster and Emergency Management are highly debated among experts. Fast communication will help to deal with emergencies. Problem is with the network connection and data exchange. The paper suggests a solution, which allows possibilities and perspectives of new flexible communication platform to the protection of communication systems for crisis management. This platform is used for everyday communication and communication in crisis situations too.
Abstract: This paper demonstrates the bus location system for
the route bus through the experiment in the real environment. A
bus location system is a system that provides information such as
the bus delay and positions. This system uses actual services and
positions data of buses, and those information should match data
on the database. The system has two possible problems. One, the
system could cost high in preparing devices to get bus positions.
Two, it could be difficult to match services data of buses. To avoid
these problems, we have developed this system at low cost and short
time by using the smart phone with GPS and the bus route system.
This system realizes the path planning considering bus delay and
displaying position of buses on the map. The bus location system
was demonstrated on route buses with smart phones for two months.
Abstract: This paper presents the comparison ageing deterioration of silicone rubber housing material for outdoor polymer insulators by using salt fog ageing test based on IEC 61109 and outdoor exposure test.Four types of high temperature silicone vulcanized silicone rubber sheet with different amount of ATH were used as testing specimen. For salt fog ageing test, the specimens were tested continuously 1000 hours with energized in test chamber. For outdoor exposure test, the specimens were hung continuously 18 months without energized. Physical and chemical analyses were conducted to evaluate degree of ageing deterioration of tested specimens. Slightly surface erosion was observed on specimen surface after salt fog ageing test and no erosion was observed on surface of outdoor exposure specimen. However, comparable degree of ageing deterioration can be seen from surface analysis results.
Abstract: In the past years, the world has witnessed significant work in the field of Manufacturing. Special efforts have been made in the implementation of new technologies, management and control systems, among many others which have all evolved the field. Closely following all this, due to the scope of new projects and the need of turning the existing flexible ideas into more autonomous and intelligent ones, i.e.: moving toward a more intelligent manufacturing, the present paper emerges with the main aim of contributing to the analysis and a few customization issues of a new iCIM 3000 system at the IPSAM. In this process, special emphasis in made on the material flow problem. For this, besides offering a description and analysis of the system and its main parts, also some tips on how to define other possible alternative material flow scenarios and a partial analysis of the combinatorial nature of the problem are offered as well. All this is done with the intentions of relating it with the use of simulation tools, for which these have been briefly addressed with a special focus on the Witness simulation package. For a better comprehension, the previous elements are supported by a few figures and expressions which would help obtaining necessary data. Such data and others will be used in the future, when simulating the scenarios in the search of the best material flow configurations.
Abstract: A catastrophic earthquake measuring 6.3 on the
Richter scale struck the Christchurch, New Zealand Central Business
District on February 22, 2012, abruptly disrupting the business of
teaching and learning at Christchurch Polytechnic Institute of
Technology. This paper presents the findings from a study
undertaken about the complexity of delivering an educational
programme in the face of this traumatic natural event. Nine
interconnected themes emerged from this multiple method study:
communication, decision making, leader- and follower-ship,
balancing personal and professional responsibilities, taking action,
preparedness and thinking ahead, all within a disruptive and uncertain
context. Sustainable responses that maximise business continuity, and
provide solutions to practical challenges, are among the study-s
recommendations.
Abstract: Design for Disassembly (DfD) aims to reuse the
structural components instead of demolition followed by recycling of
the demolition debris. This concept preserves the invested embodied
energy of materials, thus reducing inputs of new embodied energy
during materials reprocessing or remanufacturing. Both analytical and
experimental research on a proposed DfD beam-column connection
for use in residential apartments is currently investigated at the
National University of Singapore in collaboration with the Housing
and Development Board of Singapore. The present study reports on
the results of a numerical analysis of the proposed connection utilizing
finite element analysis. The numerical model was calibrated and
validated by comparison against experimental results. Results of a
parametric study will also be presented and discussed.
Abstract: Rapid Prototyping (RP) is a technology that produces models and prototype parts from 3D CAD model data, CT/MRI scan data, and model data created from 3D object digitizing systems. There are several RP process like Stereolithography (SLA), Solid Ground Curing (SGC), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), 3D Printing (3DP) among them SLS and FDM RP processes are used to fabricate pattern of custom cranial implant. RP technology is useful in engineering and biomedical application. This is helpful in engineering for product design, tooling and manufacture etc. RP biomedical applications are design and development of medical devices, instruments, prosthetics and implantation; it is also helpful in planning complex surgical operation. The traditional approach limits the full appreciation of various bony structure movements and therefore the custom implants produced are difficult to measure the anatomy of parts and analyze the changes in facial appearances accurately. Cranioplasty surgery is a surgical correction of a defect in cranial bone by implanting a metal or plastic replacement to restore the missing part. This paper aims to do a comparative study on the dimensional error of CAD and SLS RP Models for reconstruction of cranial defect by comparing the virtual CAD with the physical RP model of a cranial defect.
Abstract: Internet security attack could endanger the privacy of
World Wide Web users and the integrity of their data. The attack can
be carried out on today's most secure systems- browsers, including
Netscape Navigator and Microsoft Internet Explorer. There are too
many types, methods and mechanisms of attack where new attack
techniques and exploits are constantly being developed and
discovered. In this paper, various types of internet security attack
mechanisms are explored and it is pointed out that when different
types of attacks are combined together, network security can suffer
disastrous consequences.
Abstract: This study sought to determine whether there were relationships existed among leisure satisfaction, self-esteem, and spiritual wellness. Four hundred survey instruments were distributed, and 334 effective instruments were returned, for an effective rate of 83.5%. The participants were recruited from a purposive sampling that subjects were at least 60 years of age and retired in Tainan City, Taiwan. Three instruments were used in this research: Leisure Satisfaction Scale (LSS), Self-Esteem Scale (SES), and Spirituality Assessment Scale (SAS). The collected data were analyzed statistically. The findings of this research were as follows: 1. There is significantly correlated between leisure satisfaction and spiritual wellness. 2. There is significantly correlated between leisure satisfaction and self-esteem. 3. There is significantly correlated between spiritual wellness and self-esteem.