Abstract: Fluid flow in cylinders of elliptic cross-section was investigated. Fluid used is Liquefied petroleum gas (LPG). LPG found in Nigeria contains majorly butane with percentages of propane. Commercial available code FLUENT which uses finite volume method was used to solve fluid flow governing equations. There has been little attention paid to fluid flow in cylindrical elliptic pipes. The present work aims to predict the LPG gas flow in cylindrical pipes of elliptic cross-section. Results of flow parameters of velocity and pressure distributions are presented. Results show that the pressure drop in elliptic pipes is higher than circular pipe of the same cross-sectional area. This is an important result as the pressure drop is related to the pump power needed to drive the flow. Results show that the velocity increases towards centre of the pipe as the flow moves downstream, and also increases towards the outlet of the pipe.
Abstract: Downward turbulent bubbly flows in pipes were
modeled using computational fluid dynamics tools. The
Hydrodynamics, phase distribution and turbulent structure of twophase
air-water flow in a 57.15 mm diameter and 3.06 m length
vertical pipe was modeled by using the 3-D Eulerian-Eulerian
multiphase flow approach. Void fraction, liquid velocity and
turbulent fluctuations profiles were calculated and compared against
experimental data. CFD results are in good agreement with
experimental data.
Abstract: A lightpipe is an about 99 percent specular reflective
mirror pipe or duct that is used for the transmission of the daylight
from the outside into a building. The lightpipes are usually used in
the daylighting buildings, in the residential, industrial and
commercial sectors. This paper is about the performances of a
lightpipe installed in a laboratory (3 m x 2.6 m x 3 m) without
windows. The aim is to analyse the luminous intensity distribution
for several sky/sun conditions. The lightpipe was monitored during
the year 2006. The lightpipe is 1 m long and the diameter of the top
collector and of the internal diffuser device is 0.25 m. In the
laboratory there are seven illuminance sensors: one external is
located on the roof of the laboratory and six internal sensors are
connected to a data acquisition system. The internal sensors are
positioned under the internal diffusive device at an height of 0.85 m
from the floor to simulate a working plane. The numerical data are
obtained through a simulation software. This paper shows the
comparison between the experimental and numerical results
concerning the behavior of the lightpipe.
Abstract: Two-phase frictional pressure drop data were
obtained for condensation of carbon dioxide in single horizontal
micro tube of inner diameter ranged from 0.6 mm up to 1.6 mm over
mass flow rates from 2.5*10-5 to 17*10-5 kg/s and vapor qualities
from 0.0 to 1.0. The inlet condensing pressure is changed from 33.5
to 45 bars. The saturation temperature ranged from -1.5 oC up to 10
oC. These data have then been compared against three (two-phase)
frictional pressure drop prediction methods. The first method is by
Muller-Steinhagen and Heck (Muller-Steinhagen H, Heck K. A
simple friction pressure drop correlation for two-phase flow in pipes.
Chem. Eng. Process 1986;20:297–308) and that by Gronnerud R.
Investigation of liquid hold-up, flow-resistance and heat transfer in
circulation type evaporators, part IV: two-phase flow resistance in
boiling refrigerants, Annexe 1972. Then the method used by
FriedelL. Improved friction pressures drop in horizontal and vertical
two-phase pipe flow. European Two-Phase Flow Group Meeting,
Paper E2; 1979 June, Ispra, Italy. The methods are used by M.B Ould
Didi et al (2001) “Prediction of two-phase pressure gradients of
refrigerant in horizontal tubes". Int.J.of Refrigeration 25(2002) 935-
947. The best available method for annular flow was that of Muller-
Steinhagen and Heck. It was observed that the peak in the two-phase
frictional pressure gradient is at high vapor qualities.
Abstract: Heat pipes are two-phase heat transfer devices with
high effective thermal conductivity. Due to the high heat transport
capacity, heat exchanger with heat pipes has become much smaller
than traditional heat exchangers in handling high heat fluxes. With
the working fluid in a heat pipe, heat can be absorbed on the
evaporator region and transported to the condenser region where the
vapour condenses releasing the heat to the cooling media. Heat pipe
technology has found increasing applications in enhancing the
thermal performance of heat exchangers in microelectranics, energy
saving in HVAC systems for operating rooms,surgery centers, hotels,
cleanrooms etc, temperature regulation systems for the human body
and other industrial sectors. Development activity in heat pipe and
thermosyphon technology in asia in recent years is surveyed. Some
new results obtained in Australia and other countries are also
included.
Abstract: The results of an experimental study of the process of
convective and boiling heat transfer in the vessel with stirrer for
smooth and rough ring-shaped pipes are presented. It is established
that creation of two-dimensional artificial roughness on the heated
surface causes the essential (~100%) intensification of convective
heat transfer. In case of boiling the influence of roughness appears on
the initial stage of boiling and in case of fully developed nucleate
boiling there was no intensification of heat transfer. The similitude
equation for calculating convective heat transfer coefficient, which
generalizes well experimental data both for the smooth and the rough
surfaces is proposed.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: Water pipe network is installed underground and once equipped, it is difficult to recognize the state of pipes when the leak or burst happens. Accordingly, post management is often delayed
after the fault occurs. Therefore, the systematic fault management system of water pipe network is required to prevent the accident and
minimize the loss. In this work, we develop online fault detection system of water pipe network using data of pipes such as flow rate
or pressure. The transient model describing water flow in pipelines
is presented and simulated using MATLAB. The fault situations such
as the leak or burst can be also simulated and flow rate or pressure data when the fault happens are collected. Faults are detected using
statistical methods of fast Fourier transform and discrete wavelet transform, and they are compared to find which method shows the
better fault detection performance.
Abstract: This study offers a new simple method for assessing
an axial part-through crack in a pipe wall. The method utilizes simple
approximate expressions for determining the fracture parameters K,
J, and employs these parameters to determine critical dimensions of a
crack on the basis of equality between the J-integral and the J-based
fracture toughness of the pipe steel. The crack tip constraint is taken
into account by the so-called plastic constraint factor C, by which the
uniaxial yield stress in the J-integral equation is multiplied. The
results of the prediction of the fracture condition are verified by burst
tests on test pipes.
Abstract: Corrosion of metallic water pipelines buried below
ground surface is a function of the nature of the surrounding soil and
groundwater. This gives the importance of knowing the physical and
chemical characteristics of the pipe-s surrounding environment. The
corrosion of externally – unprotected metallic water pipelines,
specially ductile iron pipes, in localities with aggressive soil
conditions is becoming a significant problem. Anticorrosive
protection for metallic water pipelines, their fittings and accessories
is very important, because they may be attached by corrosion with
time. The tendency of a metallic substrate to corrode is a function of
the surface characteristics of the metal and of the metal/protective
film interface, the physical, electrical and electrochemical properties
of the film, and the nature of the environment in which the pipelines
system is placed. In this work the authors have looked at corrosion
problems of water pipelines and their control. The corrosive
properties of groundwater and soil environments are reviewed, and
parameters affecting corrosion are discussed. The purpose of this
work is to provide guidelines for materials selection in water and soil
environments, and how the water pipelines can be protected against
metallic corrosion.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: For the efficient and safe use of the cable-stayed
bridge, a design based on the detailed local analysis of the cable anchor
system is required. Also, a theoretical design process for the anchor
system should be prepared and reviewed. Generally, the size of the
fixing pipe in the anchor system is decided according to the
specifications prepared by cable-manufacturing companies, and
accordingly, there is difficulty determining the initial inner diameters
of the fixing pipes. As such, there is no choice but to use the products
with the existing sizes. In this study, the existing design process of the
fixing pipe, is a type of guide pipe anchor in the cable anchor system,
is reviewed, a formula determining the thickness of the fixing pipe is
proposed, and the convenience and validity of the suggested equation
is compared with the results of the existing designs to verify its
convenience and validity.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: A dent is a gross distortion of the pipe cross-section.
Dent depth is defined as the maximum reduction in the diameter of
the pipe compared to the original diameter. Pipeline dent finite
element (FE) simulation and theoretical analysis are conducted in this
paper to develop an understanding of the geometric characteristics
and strain distribution in the pressurized dented pipe. Based on the
results, the magnitude of the denting force increases significantly
with increasing the internal pressure, and the maximum
circumferential and longitudinal strains increase by increasing the
internal pressure and the dent depth. The results can be used for
characterizing dents and ranking their risks to the integrity of a
pipeline.
Abstract: This paper describes the design and development of pico-hydro generation system using consuming water distributed to houses. Water flow in the domestic pipes has kinetic energy that potential to generate electricity for energy storage purposes in addition to the routine activities such as laundry, cook and bathe. The inherent water pressure and flow inside the pipe from utility-s main tank that used for those usual activities is also used to rotate small scale hydro turbine to drive a generator for electrical power generation. Hence, this project is conducted to develop a small scale hydro generation system using consuming water distributed to houses as an alternative electrical energy source for residential use.
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: To explore pipelines is one of various bio-mimetic
robot applications. The robot may work in common buildings such as
between ceilings and ducts, in addition to complicated and massive
pipeline systems of large industrial plants. The bio-mimetic robot finds
any troubled area or malfunction and then reports its data. Importantly,
it can not only prepare for but also react to any abnormal routes in the
pipeline. The pipeline monitoring tasks require special types of mobile
robots. For an effective movement along a pipeline, the movement of
the robot will be similar to that of insects or crawling animals. During
its movement along the pipelines, a pipeline monitoring robot has an
important task of finding the shapes of the approaching path on the
pipes. In this paper we propose an effective solution to the pipeline
pattern recognition, based on the fuzzy classification rules for the
measured IR distance data.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: In this paper, transversal vibration of buried pipelines
during loading induced by underground explosions is analyzed. The
pipeline is modeled as an infinite beam on an elastic foundation, so
that soil-structure interaction is considered by means of transverse
linear springs along the pipeline. The pipeline behavior is assumed to
be ideal elasto-plastic which an ultimate strain value limits the plastic
behavior. The blast loading is considered as a point load, considering
the affected length at some point of the pipeline, in which the
magnitude decreases exponentially with time. A closed-form solution
for the quasi-static problem is carried out for both elastic and elasticperfect
plastic behaviors of pipe materials. At the end, a comparative
study on steel and polyethylene pipes with different sizes buried in
various soil conditions, affected by a predefined underground
explosion is conducted, in which effect of each parameter is
discussed.
Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.