Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: We show that Chebyshev Polynomials are a practical representation of computable functions on the computable reals. The paper presents error estimates for common operations and demonstrates that Chebyshev Polynomial methods would be more efficient than Taylor Series methods for evaluation of transcendental functions.
Abstract: This analysis investigates the distortion of flow
measurement and the increase of cavitation along orifice
flowmeter. The analysis using the numerical method (CFD)
validated the distortion of flow measurement through the inlet
velocity profile considering the convergence and grid
dependency. Realizable k-e model was selected and y+ was
about 50 in this numerical analysis. This analysis also estimated
the vulnerability of cavitation effect due to inlet velocity profile.
The investigation concludes that inclined inlet velocity profile
could vary the pressure which was measured at pressure tab
near pipe wall and it led to distort the pressure values ranged
from -3.8% to 5.3% near the orifice plate and to make the
increase of cavitation. The investigation recommends that the
fully developed inlet velocity flow is beneficial to accurate flow
measurement in orifice flowmeter.
Abstract: The modified Arcan fixture was used in order to
investigate the mixed mode fracture properties of high strength steel
butt weld through experimental and numerical analysis. The fixture
consisted of a central section with "butterfly-shaped" specimen that
had central crack. The specimens were under pure mode I (opening),
pure mode II (shearing) and all in plane mixed mode loading angles
starting from 0 to 90 degrees. The geometric calibration factors were
calculated with the aid of finite element analysis for various loading
mode and different crack length (0.45≤ a/w ≤0.55) and the critical
fracture loads obtained experimentally. The critical fracture
toughness (KIC & KIIC) estimated with experimental and numerical
analysis under mixed mode loading conditions.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: When the foundations of structures under cyclic
loading with amplitudes less than their permissible load, the concern exists often for the amount of uniform and non-uniform settlement of
such structures. Storage tank foundations with numerous filling and discharging and railways ballast course under repeating
transportation loads are examples of such conditions. This paper
deals with the effects of using the new generation of reinforcements,
Grid-Anchor, for the purpose of reducing the permanent settlement
of these foundations under the influence of different proportions of
the ultimate load. Other items such as the type and the number of
reinforcements as well as the number of loading cycles are studied numerically. Numerical models were made using the Plaxis3D
Tunnel finite element code. The results show that by using gridanchor
and increasing the number of their layers in the same
proportion as that of the cyclic load being applied, the amount of
permanent settlement decreases up to 42% relative to unreinforced
condition depends on the number of reinforcement layers and percent
of applied load and the number of loading cycles to reach a constant
value of dimensionless settlement decreases up to 20% relative to
unreinforced condition.
Abstract: Many footbridges have natural frequencies that
coincide with the dominant frequencies of the pedestrian-induced
load and therefore they have a potential to suffer excessive vibrations
under dynamic loads induced by pedestrians. Some of the design
standards introduce load models for pedestrian loads applicable for
simple structures. Load modeling for more complex structures, on the
other hand, is most often left to the designer. The main focus of this
paper is on the human induced forces transmitted to a footbridge and
on the ways these loads can be modeled to be used in the dynamic
design of footbridges. Also design criteria and load models proposed
by widely used standards were introduced and a comparison was
made. The dynamic analysis of the suspension bridge in Kolin in the
Czech Republic was performed on detailed FEM model using the
ANSYS program system. An attempt to model the load imposed by a
single person and a crowd of pedestrians resulted in displacements
and accelerations that are compared with serviceability criteria.