Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: In this manuscript, a wavelet-based blind
watermarking scheme has been proposed as a means to provide
security to authenticity of a fingerprint. The information used for
identification or verification of a fingerprint mainly lies in its
minutiae. By robust watermarking of the minutiae in the fingerprint
image itself, the useful information can be extracted accurately even
if the fingerprint is severely degraded. The minutiae are converted in
a binary watermark and embedding these watermarks in the detail
regions increases the robustness of watermarking, at little to no
additional impact on image quality. It has been experimentally shown
that when the minutiae is embedded into wavelet detail coefficients
of a fingerprint image in spread spectrum fashion using a
pseudorandom sequence, the robustness is observed to have a
proportional response while perceptual invisibility has an inversely
proportional response to amplification factor “K". The DWT-based
technique has been found to be very robust against noises,
geometrical distortions filtering and JPEG compression attacks and is
also found to give remarkably better performance than DCT-based
technique in terms of correlation coefficient and number of erroneous
minutiae.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible thermal multi-component gas
mixture flows in pipes. The set of the mass, momentum and enthalpy
conservation equations for gas phase is solved. Thermo-physical
properties of multi-component gas mixture are calculated by solving
the Equation of State (EOS) model. The Soave-Redlich-Kwong
(SRK-EOS) model is chosen. Gas mixture viscosity is calculated on
the basis of the Lee-Gonzales-Eakin (LGE) correlation. Numerical
analysis on rapid decompression in conventional dry gases is
performed by using the proposed mathematical model. The model is
validated on measured values of the decompression wave speed in
dry natural gas mixtures. All predictions show excellent agreement
with the experimental data at high and low pressure. The presented
model predicts the decompression in dry natural gas mixtures much
better than GASDECOM and OLGA codes, which are the most
frequently-used codes in oil and gas pipeline transport service.
Abstract: This paper presents an approach for an unequal error
protection of facial features of personal ID images coding. We
consider unequal error protection (UEP) strategies for the efficient
progressive transmission of embedded image codes over noisy
channels. This new method is based on the progressive image
compression embedded zerotree wavelet (EZW) algorithm and UEP
technique with defined region of interest (ROI). In this case is ROI
equal facial features within personal ID image. ROI technique is
important in applications with different parts of importance. In ROI
coding, a chosen ROI is encoded with higher quality than the
background (BG). Unequal error protection of image is provided by
different coding techniques and encoding LL band separately. In our
proposed method, image is divided into two parts (ROI, BG) that
consist of more important bytes (MIB) and less important bytes
(LIB). The proposed unequal error protection of image transmission
has shown to be more appropriate to low bit rate applications,
producing better quality output for ROI of the compresses image.
The experimental results verify effectiveness of the design. The
results of our method demonstrate the comparison of the UEP of
image transmission with defined ROI with facial features and the
equal error protection (EEP) over additive white gaussian noise
(AWGN) channel.
Abstract: In this study the regional stability of a rotor system which is supported on rolling bearings with radial clearance is studied. The rotor is assumed to be rigid. Due to radial clearance of bearings and dynamic configuration of system, each rolling elements of bearings has the possibility to be in contact with both of the races (under compression) or lose its contact. As a result, this change in dynamic of the system makes it to be known as switching system which is a type of Hybrid systems. In this investigation by adopting Multiple Lyapunov Function theorem and using Hamiltonian function as a candidate Lyapunov function, the stability of the system is studied. The purpose of this study is to inspect the regional stability of rotor-roller bearing and rotor-ball bearing systems.
Abstract: This paper studies stability of homogeneous beams
with piezoelectric layers subjected to axial load that is simply
supported at both ends lies on a continuous elastic foundation. The
displacement field of beam is assumed based on first order shear
deformation beam theory. Applying the Hamilton's principle, the
governing equation is established. The influences of applied voltage,
dimensionless geometrical parameter and foundation coefficient on
the stability of beam are presented. To investigate the accuracy of the
present analysis, a compression study is carried out with a known
data.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Years of extensive research in the field of speech
processing for compression and recognition in the last five decades,
resulted in a severe competition among the various methods and
paradigms introduced. In this paper we include the different representations
of speech in the time-frequency and time-scale domains
for the purpose of compression and recognition. The examination of
these representations in a variety of related work is accomplished.
In particular, we emphasize methods related to Fourier analysis
paradigms and wavelet based ones along with the advantages and
disadvantages of both approaches.
Abstract: Non-saturated soils that while saturation greatly
decrease their volume, have sudden settlement due to increasing
humidity, fracture and structural crack are called loess soils. Whereas
importance of civil projects including: dams, canals and
constructions bearing this type of soil and thereof problems, it is
required for carrying out more research and study in relation to loess
soils. This research studies shear strength parameters by using
grading test, Atterberg limit, compression, direct shear and
consolidation and then effect of using cement and lime additives on
stability of loess soils is studied. In related tests, lime and cement are
separately added to mixed ratios under different percentages of soil
and for different times the stabilized samples are processed and effect
of aforesaid additives on shear strength parameters of soil is studied.
Results show that upon passing time the effect of additives and
collapsible potential is greatly decreased and upon increasing
percentage of cement and lime the maximum dry density is
decreased; however, optimum humidity is increased. In addition,
liquid limit and plastic index is decreased; however, plastic index
limit is increased. It is to be noted that results of direct shear test
reveal increasing shear strength of soil due to increasing cohesion
parameter and soil friction angle.
Abstract: The aim of this paper to characterize a larger set of
wavelet functions for implementation in a still image compression
system using SPIHT algorithm. This paper discusses important
features of wavelet functions and filters used in sub band coding to
convert image into wavelet coefficients in MATLAB. Image quality
is measured objectively using peak signal to noise ratio (PSNR) and
its variation with bit rate (bpp). The effect of different parameters is
studied on different wavelet functions. Our results provide a good
reference for application designers of wavelet based coder.
Abstract: Octree compression techniques have been used
for several years for compressing large three dimensional data
sets into homogeneous regions. This compression technique
is ideally suited to datasets which have similar values in
clusters. Oil engineers represent reservoirs as a three dimensional
grid where hydrocarbons occur naturally in clusters. This
research looks at the efficiency of storing these grids using
octree compression techniques where grid cells are broken
into active and inactive regions. Initial experiments yielded
high compression ratios as only active leaf nodes and their
ancestor, header nodes are stored as a bitstream to file on
disk. Savings in computational time and memory were possible
at decompression, as only active leaf nodes are sent to the
graphics card eliminating the need of reconstructing the original
matrix. This results in a more compact vertex table, which can
be loaded into the graphics card quicker and generating shorter
refresh delay times.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: Medical imaging uses the advantage of digital
technology in imaging and teleradiology. In teleradiology systems
large amount of data is acquired, stored and transmitted. A major
technology that may help to solve the problems associated with the
massive data storage and data transfer capacity is data compression
and decompression. There are many methods of image compression
available. They are classified as lossless and lossy compression
methods. In lossy compression method the decompressed image
contains some distortion. Fractal image compression (FIC) is a lossy
compression method. In fractal image compression an image is
coded as a set of contractive transformations in a complete metric
space. The set of contractive transformations is guaranteed to
produce an approximation to the original image. In this paper FIC is
achieved by PIFS using quadtree partitioning. PIFS is applied on
different images like , Ultrasound, CT Scan, Angiogram, X-ray,
Mammograms. In each modality approximately twenty images are
considered and the average values of compression ratio and PSNR
values are arrived. In this method of fractal encoding, the
parameter, tolerance factor Tmax, is varied from 1 to 10, keeping the
other standard parameters constant. For all modalities of images the
compression ratio and Peak Signal to Noise Ratio (PSNR) are
computed and studied. The quality of the decompressed image is
arrived by PSNR values. From the results it is observed that the
compression ratio increases with the tolerance factor and
mammogram has the highest compression ratio. The quality of the
image is not degraded upto an optimum value of tolerance factor,
Tmax, equal to 8, because of the properties of fractal compression.
Abstract: Among other factors that characterize satellite communication
channels is their high bit error rate. We present a system for
still image transmission over noisy satellite channels. The system
couples image compression together with error control codes to
improve the received image quality while maintaining its bandwidth
requirements. The proposed system is tested using a high resolution
satellite imagery simulated over the Rician fading channel. Evaluation
results show improvement in overall system including image quality
and bandwidth requirements compared to similar systems with different
coding schemes.
Abstract: A numerical study is presented on buckling and post
buckling behaviour of laminated carbon fiber reinforced plastic
(CFRP) thin-walled cylindrical shells under axial compression using
asymmetric meshing technique (AMT). Asymmetric meshing
technique is a perturbation technique to introduce disturbance without
changing geometry, boundary conditions or loading conditions.
Asymmetric meshing affects predicted buckling load, buckling mode
shape and post-buckling behaviour. Linear (eigenvalue) and nonlinear
(Riks) analyses have been performed to study the effect of
asymmetric meshing in the form of a patch on buckling behaviour.
The reduction in the buckling load using Asymmetric meshing
technique was observed to be about 15%. An isolated dimple formed
near the bifurcation point and the size of which increased to reach a
stable state in the post-buckling region. The load-displacement curve
behaviour applying asymmetric meshing is quite similar to the curve
obtained using initial geometric imperfection in the shell model.
Abstract: Stability of functionally graded beams with piezoelectric layers subjected to axial compressive load that is simply supported at both ends is studied in this paper. The displacement field of beam is assumed based on first order shear deformation beam theory. Applying the Hamilton's principle, the governing equation is established. The influences of applied voltage, dimensionless geometrical parameter, functionally graded index and piezoelectric thickness on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study is carried out with a known data.
Abstract: This paper shows that the economy of any country
can be presented as three different shells such as: economic shell of a
big, a medium and a small business. The new concepts were
introduced such as: volume of an economic shell, coefficient of
shell-s expansion (compression) etc. These shells can expansion or
compress under action by internal or external powers and when shell
expansions - it means the rising of a business activity and
compression shows us that economy goes on recession. This process
of an expansion or a compression can develop in the various ways
like linear, logarithm or any other mathematical laws.
Abstract: Authentication of multimedia contents has gained much attention in recent times. In this paper, we propose a secure semi-fragile watermarking, with a choice of two watermarks to be embedded. This technique operates in integer wavelet domain and makes use of semi fragile watermarks for achieving better robustness. A self-recovering algorithm is employed, that hides the image digest into some Wavelet subbands to detect possible malevolent object manipulation undergone by the image (object replacing and/or deletion). The Semi-fragility makes the scheme tolerant for JPEG lossy compression as low as quality of 70%, and locate the tempered area accurately. In addition, the system ensures more security because the embedded watermarks are protected with private keys. The computational complexity is reduced using parameterized integer wavelet transform. Experimental results show that the proposed scheme guarantees the safety of watermark, image recovery and location of the tempered area accurately.
Abstract: This research evaluated and compared the thermodynamic performance of heat pump systems which can be run under two different modes as air to air and air to water by using only one compressor. To achieve this comparison an experimental performance study was made on a traditional vapor compressed heat pump system that can be run air to air mode and air to water mode by help of a valve. The experiments made under different thermal conditions. Thermodynamic performance of the systems are presented and compared with each other for different working conditions.
Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.