Abstract: A number of toxic chlorophenolic compounds are formed during pulp bleaching. The nature and concentration of these chlorophenolic compounds largely depends upon the amount and nature of bleaching chemicals used. These compounds are highly recalcitrant and difficult to remove but are partially removed by the biochemical treatment processes adopted by the paper industry. Identification and estimation of these chlorophenolic compounds has been carried out in the primary and secondary clarified effluents from the paper mill by GCMS. Twenty-six chorophenolic compounds have been identified and estimated in paper mill waste waters. Electrochemical treatment is an efficient method for oxidation of pollutants and has successfully been used to treat textile and oil waste water. Electrochemical treatment using less expensive anode material, stainless steel electrodes has been tried to study their removal. The electrochemical assembly comprised a DC power supply, a magnetic stirrer and stainless steel (316 L) electrode. The optimization of operating conditions has been carried out and treatment has been performed under optimized treatment conditions. Results indicate that 68.7% and 83.8% of cholorphenolic compounds are removed during 2 h of electrochemical treatment from primary and secondary clarified effluent respectively. Further, there is a reduction of 65.1, 60 and 92.6% of COD, AOX and color, respectively for primary clarified and 83.8%, 75.9% and 96.8% of COD, AOX and color, respectively for secondary clarified effluent. EC treatment has also been found to increase significantly the biodegradability index of wastewater because of conversion of non- biodegradable fraction into biodegradable fraction. Thus, electrochemical treatment is an efficient method for the degradation of cholorophenolic compounds, removal of color, AOX and other recalcitrant organic matter present in paper mill waste water.
Abstract: Increase of emergency incidents and crisis situations
requires proactive crisis management of authorities and for its
solution. Application Business Continuity Management helps the
crisis management authorities to quickly and responsibly respond to
threats. It also helps effectively and efficiently planning powers and
resources. The main goal of this article is describing Military
Continuity Management System (MCMS) based on the principles of
Business Continuity Management System (BCMS) for dealing with
floods in the territory of the selected municipalities. There are
explained steps of loading, running and evaluating activities in the
software application MCMS. Software MCMS provides complete
control over the tasks, contribute a comprehensive and responsible
approach solutions to solution floods in the municipality.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: In order to achieve competitive advantage and better
performance of firm, supply chain management (SCM) strategy
should support and drive forward business strategy. It means that
supply chain should be aligned with business strategy, at the same
time supply chain (SC) managers need to use appropriate information
system (IS) solution to support their strategy, which would lead to
stay competitive. There are different kinds of IS strategies which
enable managers to meet the SC requirement by selecting the best IS
strategy. Therefore, it is important to align IS strategies and practices
with SC strategies and practices, which could help us to plan for an
IS application that supports and enhances a SCMS. In this study,
aligning IS with SC in strategy level is considered. The main aim of
this paper is to align the various IS strategies with SCM strategies
and demonstrate their impact on SC and firm performance.
Abstract: The ARMrayan Multimedia Mobile CMS (Content
Management System) is the first mobile CMS that gives the
opportunity to users for creating multimedia J2ME mobile
applications with their desired content, design and logo; simply,
without any need for writing even a line of code. The low-level
programming and compatibility problems of the J2ME, along with
UI designing difficulties, makes it hard for most people –even
programmers- to broadcast their content to the widespread mobile
phones used by nearly all people. This system provides user-friendly,
PC-based tools for creating a tree index of pages and inserting
multiple multimedia contents (e.g. sound, video and picture) in each
page for creating a J2ME mobile application. The output is a standalone
Java mobile application that has a user interface, shows texts
and pictures and plays music and videos regardless of the type of
devices used as long as the devices support the J2ME platform.
Bitmap fonts have also been used thus Middle Eastern languages can
be easily supported on all mobile phone devices. We omitted
programming concepts for users in order to simplify multimedia
content-oriented mobile applictaion designing for use in educational,
cultural or marketing centers. Ordinary operators can now create a
variety of multimedia mobile applications such as tutorials,
catalogues, books, and guides in minutes rather than months.
Simplicity and power has been the goal of this CMS. In this paper,
we present the software engineered-designed concepts of the
ARMrayan MCMS along with the implementation challenges faces
and solutions adapted.
Abstract: The scale, complexity and worldwide geographical
spread of the LHC computing and data analysis problems are
unprecedented in scientific research. The complexity of processing
and accessing this data is increased substantially by the size and
global span of the major experiments, combined with the limited
wide area network bandwidth available. We present the latest
generation of the MONARC (MOdels of Networked Analysis at
Regional Centers) simulation framework, as a design and modeling
tool for large scale distributed systems applied to HEP experiments.
We present simulation experiments designed to evaluate the
capabilities of the current real-world distributed infrastructure to
support existing physics analysis processes and the means by which
the experiments bands together to meet the technical challenges
posed by the storage, access and computing requirements of LHC
data analysis within the CMS experiment.