Abstract: This paper presents the performance of electricity
generation and consumption from solar generator installed at
Rajabhat Suan Sunandha’s learning center in Samutsongkram.
The result from the experiment showed that solar cell began to
work and distribute the current into the system when the solar energy
intensity was 340 w/m2, starting from 8:00 am to 4:00 pm (duration
of 8 hours). The highest intensity read during the experiment was
1,051.64w/m2. The solar power was 38.74kWh/day. The
electromotive force from solar cell averagely was 93.6V. However,
when connecting solar cell with the battery charge controller system,
the voltage was dropped to 69.07V. After evaluating the power
distribution ability and electricity load of tested solar cell, the result
showed that it could generate power to 11 units of 36-watt
fluorescent lamp bulbs, which was altogether 396W. In the
meantime, the AC to DC power converter generated 3.55A to the
load, and gave 781VA.
Abstract: In this paper, the optimum design for renewable energy system powered an aquaculture pond was determined. Hybrid Optimization Model for Electric Renewable (HOMER) software program, which is developed by U.S National Renewable Energy Laboratory (NREL), is used for analyzing the feasibility of the stand alone and hybrid system in this study. HOMER program determines whether renewable energy resources satisfy hourly electric demand or not. The program calculates energy balance for every 8760 hours in a year to simulate operation of the system. This optimization compares the demand for the electrical energy for each hour of the year with the energy supplied by the system for that hour and calculates the relevant energy flow for each component in the model. The essential principle is to minimize the total system cost while HOMER ensures control of the system. Moreover the feasibility analysis of the energy system is also studied. Wind speed, solar irradiance, interest rate and capacity shortage are the parameters which are taken into consideration. The simulation results indicate that the hybrid system is the best choice in this study, yielding lower net present cost. Thus, it provides higher system performance than PV or wind stand alone systems.
Abstract: The association between sensory problems and cognitive abilities has been studied in individuals with Autism Spectrum Disorders (ASDs). In this study, we used a Neuropsychological Test to evaluate memory and attention in ASDs children with sensory problems compared to the ASDs children without sensory problems. Four visual memory tests of Cambridge Neuropsychological Test Automated Battery (CANTAB) including Big/little circle (BLC), Simple Reaction Time (SRT) Intra /Extra dimensional set shift (IED), Spatial recognition memory (SRM), were administered to 14 ASDs children with sensory problems compared to 13 ASDs without sensory problems aged 3 to 12 with IQ of above 70. ASDs individuals with sensory problems performed worse than the ASDs group without sensory problems on comprehension, learning, reversal and simple reaction time tasks, and no significant difference between the two groups was recorded in terms of the visual memory and visual comprehension tasks. The findings of this study suggest that ASDs children with sensory problems are facing deficits in learning, comprehension, reversal, and speed of response to a stimulus.
Abstract: The aim of this paper is to use an experiential view of wine tourism to develop a battery of items that can potentially capture the overall Douro Valley experience from the tourist’s perspective. The Douro Valley, a UNESCO World Heritage region located in Portugal, was the target of this study. The research took a mixed approach using both qualitative and quantitative designs. Firstly, we combine the literature review on service quality scales with a content analysis of five in-depth interviews with winery managers and a focus group with wine tourists to identify the main dimensions of the overall tourism experience and to develop a battery of items for each dimension. Eight dimensions of the overall wine tourism experience came out, as follows: winery service and staff, winery facilities, winery service, wine product, wine region environment, wine region accessibilities, wine region´s offerings, and the wine region and winery reputation.
Abstract: Mobile Ad-Hoc Network (MANET) is a network without infrastructure dynamically formed by autonomous system of mobile nodes that are connected via wireless links. Mobile nodes communicate with each other on the fly. In this network each node also acts as a router. The battery power and the bandwidth are very scarce resources in this network. The network lifetime and connectivity of nodes depend on battery power. Therefore, energy is a valuable constraint which should be efficiently used. In this paper we survey various energy efficient routing protocols. The energy efficient routing protocols are classified on the basis of approaches they use to minimize the energy consumption. The purpose of this paper is to facilitate the research work and combine the existing solution and to develop a more energy efficient routing mechanism.
Abstract: The shortage of the automotive market in relation
to options for sources of high power car audio systems, led to
development of this work. Thus, we developed a source with stabilized
voltage with 4320 W effective power. Designed to the voltage of
14.4 V and a choice of two currents: 30 A load option in battery
banks and 300 A at full load. This source can also be considered as
a source of general use dedicated commercial with a simple control
circuit in analog form based on discrete components. The assembly of
power circuit uses a methodology for higher power than the initially
stipulated.
Abstract: Cloud computing (CC) and mobile cloud computing (MCC) have advanced rapidly the last few years. Today, MCC undergoes fast improvement and progress in terms of hardware (memory, embedded sensors, power consumption, touch screen, etc.) software (more and more sophisticated mobile applications) and transmission (higher data transmission rates achieved with different technologies such as 3Gs). This paper presents a review on the concept of CC and MCC. Then, it discusses what has been done regarding middleware in cloud and mobile cloud computing. Later, it shows the architecture of our proposed middleware along with its functionalities which will be provided to mobile clients in order to overcome the well known problems (such as low battery power, slow CPU speed and little memory…).
Abstract: In this paper a hybrid distributed generation (DG) system connected to isolated load is studied. The DG system consisting of photo voltaic (PV) system, fuel cells, aqua electrolyzer, diesel engine generator and a battery energy storage system. The ambient temperature value of PV is taken as constant to make the output power of PV is directly proportional to the radiation and output power of other DG sources and frequency of the system is controlled by simple integral (I), proportional plus integral (PI), and proportional plus integral and derivative(PID) controllers. A maiden attempt is made to apply a more recent and powerful optimization technique named as bacterial foraging technique for optimization of controllers gains of the proposed hybrid DG system. The system responses with bacterial foraging based controllers are compared with that of classical method. Investigations reveal that bacterial foraging based controllers gives better responses than the classical method and also PID controller is best. Sensitivity analysis is carried out which demonstrates the robustness of the optimized gain values for system loading condition.
Abstract: Digital systems are said to be constructed using basic logic gates. These gates are the NOR, NAND, AND, OR, EXOR & EXNOR gates. This paper presents a robust three transistors (3T) based NAND and NOR gates with precise output logic levels, yet maintaining equivalent performance than the existing logic structures. This new set of 3T logic gates are based on CMOS inverter and Pass Transistor Logic (PTL). The new universal logic gates are characterized by better speed and lower power dissipation which can be straightforwardly fabricated as memory ICs for high performance computer networks. The simulation tests were performed using standard BPTM 22nm process technology using SYNOPSYS HSPICE. The 3T NAND gate is evaluated using C17 benchmark circuit and 3T NOR is gate evaluated using a D-Latch. According to HSPICE simulation in 22 nm CMOS BPTM process technology under given conditions and at room temperature, the proposed 3T gates shows an improvement of 88% less power consumption on an average over conventional CMOS logic gates. The devices designed with 3T gates will make longer battery life by ensuring extremely low power consumption.
Abstract: This study was focused on polymer electrolytes containing methanesulfonic acid (MSA) and p-toluene sulfonic acid (pTSA) mixed with polyacrylamide (PAAm) respectively. Impedance Spectroscopy technique has been employed to compare the ionic conductivity of these polymer electrolytes. The ionic conductivity of the PAAm hydrogel electrolytes increase upon adding the sulfonic acids. Ionic conductivity of PAAm-pTSA is higher than PAAm-MSA. The electrochemical performance evaluations were done with the tin-air cells discharge at zero current for 30minutes and at constant current density of 2.5, 5, 7.5, 10, 12.5 and 15mA/cm2. The tin-air cell of PAAm-MSA produce higher specific discharge capacity compared to PAAm-pTSA. Open-circuit voltage measurement revealed a higher voltage for tin-air cell of PAAm-MSA which is 1.27V.
Abstract: This paper proposes an adaptive discharge time control method to balance cell voltages in alternating battery cell discharging method. In the alternating battery cell discharging method, battery cells are periodically discharged in turn. Recovery effect increases battery output voltage while the given battery cell rests without discharging, thus battery operation time of target system increases. However, voltage mismatch between cells leads two problems. First, voltage difference between cells induces inter-cell current with wasted power. Second, it degrades battery operation time, since system stops when any cell reaches to the minimum system operation voltage. To solve this problem, the proposed method adaptively controls cell discharge time to equalize both cell voltages. In the proposed method, battery operation time increases about 19%, while alternating battery cell discharging method shows about 7% improvement.
Abstract: Previous research has indicated a variable effect of exercise on adolescents’ cognitive function. However, comparisons between studies are difficult to make due to differences in: the mode, intensity and duration of exercise employed; the components of cognitive function measured (and the tests used to assess them); and the timing of the cognitive function tests in relation to the exercise. Therefore, the aim of the present study was to assess the time course (10 and 60min post-exercise) of the effects of 15min intermittent exercise on cognitive function in adolescents. 45 adolescents were recruited to participate in the study and completed two main trials (exercise and resting) in a counterbalanced crossover design. Participants completed 15min of intermittent exercise (in cycles of 1 min exercise, 30s rest). A battery of computer based cognitive function tests (Stroop test, Sternberg paradigm and visual search test) were completed 30 min pre- and 10 and 60min post-exercise (to assess attention, working memory and perception respectively).The findings of the present study indicate that on the baseline level of the Stroop test, 10min following exercise response times were slower than at any other time point on either trial (trial by session time interaction, p = 0.0308). However, this slowing of responses also tended to produce enhanced accuracy 10min post-exercise on the baseline level of the Stroop test (trial by session time interaction, p = 0.0780). Similarly, on the complex level of the visual search test there was a slowing of response times 10 min post-exercise (trial by session time interaction, p = 0.0199). However, this was not coupled with an improvement in accuracy (trial by session time interaction, p = 0.2349). The mid-morning bout of exercise did not affect response times or accuracy across the morning on the Sternberg paradigm. In conclusion, the findings of the present study suggest an equivocal effect of exercise on adolescents' cognitive function. The mid-morning bout of exercise appears to cause a speed-accuracy trade off immediately following exercise on the Stroop test (participants become slower but more accurate), whilst slowing response times on the visual search test and having no effect on performance on the Sternberg paradigm. Furthermore, this work highlights the importance of the timing of the cognitive function tests relative to the exercise and the components of cognitive function examined in future studies.
Abstract: This paper proposes an alternating discharge method of multiple battery cells to extend battery operation time. In the proposed method, two battery cells are periodically connected in turn to a mobile device and only one cell supply power while the other rests. Battery operation time of the connecting cell decreases due to rate-capacity effect, while that of the resting cell increases due to recovery effect. These two effects conflict each other, but recovery effect is generally larger than rate-capacity effect and battery lifetime is extended. It was found from the result that battery operation time increase about 7% by using alternating battery cell discharge.
Abstract: In recent years Li-Ion batteries getting more attention among the Electrical Vehicles (EV) and Hybrid Electrical Vehicles (HEV) energy storage. Li-Ion has shown extended power density and light weight compared to other batteries readily available in the market. One of the major drawbacks in Li-Ion batteries is their sensitivity to the temperature. If the working temperature is beyond the limit, that could affect seriously on the durability and performance of Li-Ion battery. Thus Battery Thermal Management (BTM) is the most essential in adapting Li-Ion battery to the EVs and HEVs.
Abstract: This paper presents a car parking monitoring system using wireless sensor networks. Multiple sensor nodes and a sink node, a gateway, and a server constitute a wireless network for monitoring a parking lot. Each of the sensor nodes is equipped with a 3-axis AMR sensor and deployed in the center of a parking space. Each sensor node reads its sensor values periodically and transmits the data to the sink node if the current and immediate past sensor values show a difference exceeding a threshold value. The sensor nodes and sink node use the 448 MHz band for wireless communication. Since RF transmission only occurs when sensor values show abrupt changes, the number of RF transmission operations is reduced and battery power can be conserved. The data from the sensor nodes reach the server via the sink node and gateway. The server determines which parking spaces are taken by cars based upon the received sensor data and reference values. The reference values are average sensor values measured by each sensor node when the corresponding parking spot is not occupied by a vehicle. Because the decision making is done by the server, the computational burden of the sensor node is relieved, which helps reduce the duty cycle of the sensor node.
Abstract: The aim of the contribution is to project and consequently verify a testing battery which in practice would facilitate the selection of talented gymnasts for current concept of men´ s gymnastics. Based on study of professional literature a test array consisting of three parts projected – power testing, speed testing and flexibility testing– was projected. The evaluating scales used in the tests are standardized. This test array was applied to girls aged 6 - 7 during recruitment for Sokol Brno I. and SG Pelhrimov Gymnastic Club. After 6 months of training activity the projected set of tests was applied again. The results were evaluated through observation and questionnaire and they were consequently transformed into charts. Recommendation for practice was proposed based on these results.
Abstract: In this paper, an energy efficient digital baseband circuit for piezoelectric (PE) harvester powered batteryless remote control system is presented. Pulse mode PE harvester, which provides short duration of energy, is adopted to replace conventional chemical battery in wireless remote controller. The transmitter digital baseband repeats the control command transmission once the digital circuit is initiated by the power-on-reset. A power efficient data frame format is proposed to maximize the transmission repetition time. By using the proposed frame format and receiver clock and data recovery method, the receiver baseband is able to decode the command even when the received data has 20% error. The proposed transmitter and receiver baseband are implemented using FPGA and simulation results are presented.
Abstract: Solar power plants(SPPs) have shown a lot of good outcomes
in providing a various functions depending on industrial expectations by
deploying ad-hoc networking with helps of light loaded and battery powered
sensor nodes. In particular, it is strongly requested to develop an algorithm to
deriver the sensing data from the end node of solar power plants to the sink node
on time. In this paper, based on the above observation we have proposed an
IEEE802.15.4 based self routing scheme for solar power plants. The proposed
beacon based priority routing Algorithm (BPRA) scheme utilizes beacon
periods in sending message with embedding the high priority data and thus
provides high quality of service(QoS) in the given criteria. The performance
measures are the packet Throughput, delivery, latency, total energy
consumption. Simulation results under TinyOS Simulator(TOSSIM) have
shown the proposed scheme outcome the conventional Ad hoc On-Demand
Distance Vector(AODV) Routing in solar power plants.
Abstract: In this paper, we proposed an invention of an
accessory into a communication device that will help humans to be
connected universally. Generally, this device will be made up of
crystal and will combine many technologies that will enable the user
to run various applications and software anywhere and everywhere.
Bringing up the concept of from being user friendly, we had used the
crystal as the main material of the device that will trap the
surrounding lights to produce projection of its screen. This leads to a
lesser energy consumption and allows smaller sized battery to be
used, making the device less bulky. Additionally, we proposed the
usage of micro batteries as our energy source. Thus, researches
regarding crystal were made along with explanations in details of
specification and function of the technology used in the device.
Finally, we had also drawn several views of the invention from
different sides to be visualized.
Abstract: In this paper, we propose a routing scheme that guarantees
the residual lifetime of wireless sensor networks where each
sensor node operates with a limited budget of battery energy. The
scheme maximizes the communications QoS while sustaining the
residual battery lifetime of the network for a specified duration.
Communication paths of wireless nodes are translated into a directed
acyclic graph(DAG) and the maximum-flow algorithm is applied to
the graph. The found maximum flow are assigned to sender nodes, so
as to maximize their communication QoS. Based on assigned flows,
the scheme determines the routing path and the transmission rate of
data packet so that any sensor node on the path would not exhaust
its battery energy before a specified duration.