Abstract: The compressive strength development through
polymerization process of alkaline solution and fly ash blended with Microwave Incinerated Rice Husk Ash (MIRHA) is described in this
paper. Three curing conditions, which are hot gunny curing, ambient
curing, and external humidity curing are investigated to obtain the suitable curing condition for cast in situ provision. Fly ash was
blended with MIRHA at 3%, 5%, and 7% to identify the effect of blended mixes to the compressive strength and microstructure
properties of geopolymer concrete. Compressive strength results
indicated an improvement in the strength development with external humidity curing concrete samples compared to hot gunny curing and
ambient curing. Blended mixes also presented better performance
than control mixes. Improvement of interfacial transition zone (ITZ)
and micro structure in external humidity concrete samples were also
identified compared to hot gunny and ambient curing.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: Low oxygen content vanadium powder was
prepared by hydrogenation dehydrogenization (HDH). The
effect of purification treatment on hydrogen absorption kinetics
of dendritic vanadium was tested, and the effects of milling
technique on powder yield and grain size were studied. The
crystal phase, oxygen and nitrgen content, and grain size of
prepared powder were characterized and analyzed by X-ray
diffraction (XRD), oxygen and nitrogen analyzer and grain size
analyzer. The results show that the alkaline cleaning can
improve the hydrogen absorption of vanadium. The yield of
vanadium hydride powder can reach as high as 90% by 4h
ball-milling, The resultant product also have an oxygen content
less than 600μg/g, and the grain size is smaller than 37μm.
Meanwhile, the XRD results show that the phase of hydride
vanadium powder is mainly VH0.81. After a hydrogen
desorption treatment in vacuum at 700Ôäâ, the phase of the
powder converts into V and a little of V2H.
Abstract: The main objective of this research is to synthesize silk fibroin fiber for indoor air particulate removal. Silk cocoons were de-gummed using 0.5 wt % Na2CO3 alkaline solutions at 90 Ó╣ìC for 60 mins, washed with distilled water, and dried at 80 Ó╣ìC for 3 hrs in a vacuum oven. Two sets of experiment were conducted to investigate the impacts of initial particulate matter (PM) concentration and that of air flow rate on the removal efficiency. Rice bran collected from a local rice mill in Ubonratchathani province was used as indoor air contaminant in this work. The morphology and physical properties of silk fibroin (SF) fiber were measured. The SEM revealed the deposition of PM on the used fiber. The PM removal efficiencies of 72.29 ± 3.03 % and 39.33 ± 1.99 % were obtained of PM10 and PM2.5, respectively, when using the initial PM concentration at 0.040 mg/m3 and 0.020 mg/m3 of PM10 and PM2.5, respectively, with the air flow rate of 5 L/min.
Abstract: Organic farmers across Saskatchewan face soil
phosphorus (P) shortages. Due to the restriction on inputs in organic
systems, farmers rely on crop rotation and naturally-occurring
arbuscular mycorrhizal fungi (AMF) for plant P supply. Crop rotation
is important for disease, pest, and weed management. Crops that are
not colonized by AMF (non-mycorrhizal) can decrease colonization
of a following crop. An experiment was performed to quantify soil P
cycling in four cropping sequences under organic management and
determine if mustard (non-mycorrhizal) was delaying the
colonization of subsequent wheat. Soils from the four cropping
sequences were measured for inorganic soil P (Pi), AMF spore
density (SD), phospholipid fatty acid analysis (PLFA, for AMF
biomarker counts), and alkaline phosphatase activity (ALPase,
related to AMF metabolic activity). Plants were measured for AMF
colonization and P content and uptake of above-ground biomass. A
lack of difference in AMF activity indicated that mustard was not
depressing colonization. Instead, AMF colonization was largely
determined by crop type and crop rotation.
Abstract: IFP Group Technology “Sulfrex process" was used in
Iran-s South Pars Gas Complex Refineries for removing sulfur
compounds such as mercaptans, carbonyl sulfide and hydrogen
sulfide, which uses sulfonated cobalt phthalocyanine dispersed in
alkaline solution as catalyst. In this technology, catalyst and alkaline
solution were used circularly. However the stability of catalyst due to
effect of some parameters would reduce with the running of the unit
and therefore sweetening efficiency would be decreased. Hence, the
aim of this research is study the factors effecting on the stability of
catalyst.
Abstract: This study addresses the effect of impurities on the
crystallization of Na2CO3 produced within a strategy for capturing
CO2 from flue gases by alkaline absorption. A novel technology -
membrane assisted crystallization - is proposed for Na2CO3
crystallization from mother liquors containing impurities. High purity
of Na2CO3•10H2O crystals was obtained without impacting the
performance of the mass transfer of water vapor through membranes
during crystallization.
Abstract: Effect of oral administration of “Gadagi" tea on liver
function was assessed on 50 healthy male albino rats which were
grouped and administered with different doses(mg/kg) i.e low dose
(380mg/kg, 415mg/kg, 365mg/kg, 315mg/kg for “sak", “sada" and
“magani" respectively), standard dose ( 760mg/kg, 830mg/kg,
730mg/kg for “sak-, “sada" and “magani" respectively) and high dose
(1500mg/kg, 1700mg/kg and 1460mg/kg for “sak--,"sada" and
“magani" groups respectively) for a period of four weeks. Animals
that were not administered with the tea constituted the control group.
At the end of fourth week, the animals were sacrificed and their
serum alanine aminotransferase (ALT), aspartate aminotransferase
(AST), alkaline phosphatase (ALP), total protein (TP), albumin
(ALB), and globulins (GLO) were determined. Mean serum ALT and
ALP activities were significantly higher (P
Abstract: New lead-free ferroelectric relaxor ceramics were
prepared by conventional solid-state synthesis in the BaTiO3-Bi2O3-
Y2O3 systems. Some of these ceramics present a ferroelectric relaxor
with transition temperature close to room temperature. These new
materials are very interesting for applications and can replace leadbased
ceramic to prevent the toxic pollutions during the preparation
state. In the other hand, the energy band diagram shows the
potentiality of these compounds for the solar energy conversion.
Thus, some compositions have been tested successfully for H2
production upon visible light. The best activity occurs in alkaline
media with a rate evolution of about 0.15 mL g-1 mn-1 and a quantum
yield of 1% under polychromatic light.
Abstract: Sugarcane Shoots is an abundantly available
residual resources consisting of lignocelluloses which take it into
the benefit. The present study was focused on utilizing of
sugarcane shoot for reducing sugar production as a substrate in
ethanol production. Physical and chemical pretreatments of
sugarcane shoot were investigated. Results showed that the size of
sugarcane shoot influenced the cellulose content. The maximum
cellulose yield (60 %) can be obtained from alkaline pretreated
sugarcane shoot with 1.0 M NaOH at 30 oC for 90 min. The
cellulose yield reached up to 93.9% (w/w). Enzymatically
hydrolyzed of cellulosic residual in 0.04 citrate buffer (pH 5) with
celluclast 1.5L (0.7 FPU/ml) resulted in the highest amount of
reducing sugar at a rate of 32.1 g/l after 4 h incubation at 50°C,
and 100 oC for 5 min . Cellulose conversion was 55.5%.
Abstract: In this study arsenate [As(V)] removal from drinking water by coagulation process was investigated. Ferric chloride (FeCl3.6H2O) and ferrous sulfate (FeSO4.7H2O) were used as coagulant. The effects of major operating variables such as coagulant dose (1–30 mg/L) and pH (5.5–9.5) were investigated. Ferric chloride and ferrous sulfate were found as effective and reliable coagulant due to required dose, residual arsenate and coagulant concentration. Optimum pH values for maximum arsenate removal for ferrous sulfate and ferric chloride were found as 8 and 7.5. The arsenate removal efficiency decreased at neutral and acidic pH values for Fe(II) and at the high acidic and high alkaline pH for Fe(III). It was found that the increase of coagulant dose caused a substantial increase in the arsenate removal. But above a certain ferric chloride and ferrous sulfate dosage, the increase in arsenate removal was not significant. Ferric chloride and ferrous sulfate dose above 8 mg/L slightly increased arsenate removal.
Abstract: Air quality in Setapak district of Kuala Lumpur was
studied by analysing the rainwater chemical composition using ion
chromatography method. Twelve sampling sites were selected and
120 rainwater samples were collected in the period of 10 weeks. The
results of this study were compared to the earlier published data and
the evaluation showed that the NO3
- ion concentration increased from
0.41 to 3.32 ppm, while SO4
2- ion concentration increased from 0.39
to 3.26 ppm over the past two decades that is mostly due to rapid
urban development of the city. However, it was found that the
chemical composition for both residential and industrial areas does
not have significant difference. Most of the rainwater samples
showed alkaline pH (pH > 5.6). The possible factors for such alkaline
pH in rainwater samples are assumed to be the marine sources,
biomass burning and alkaline character of soil particles.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.
Abstract: The enzyme alkaline protease production was determined under
solid state fermentation using the soil bacteria Serratia marcescens
sp7. The maximum production was obtained from wheat bran
medium than ground nut shell and chemically defined medium. The
physiological fermentation factors such as pH of the medium (pH 8),
Temperature (40oC) and incubation time (48 hrs) played a vital role
in alkaline protease production in all the above. 100Mm NaCl has
given better resolution during elution of the enzymes. The enzyme
production was found to be associated with growth of the bacterial
culture.
Abstract: Enzymatic saccharification of biomass for reducing
sugar production is one of the crucial processes in biofuel production
through biochemical conversion. In this study, enzymatic
saccharification of dilute potassium hydroxide (KOH) pre-treated
Tetraselmis suecica biomass was carried out by using cellulase
enzyme obtained from Trichoderma longibrachiatum. Initially, the
pre-treatment conditions were optimised by changing alkali reagent
concentration, retention time for reaction, and temperature. The T.
suecica biomass after pre-treatment was also characterized using
Fourier Transform Infrared Spectra and Scanning Electron
Microscope. These analyses revealed that the functional group such
as acetyl and hydroxyl groups, structure and surface of T. suecica
biomass were changed through pre-treatment, which is favourable for
enzymatic saccharification process. Comparison of enzymatic
saccharification of untreated and pre-treated microalgal biomass
indicated that higher level of reducing sugar can be obtained from
pre-treated T. suecica. Enzymatic saccharification of pre-treated T.
suecica biomass was optimised by changing temperature, pH, and
enzyme concentration to solid ratio ([E]/[S]). Highest conversion of
carbohydrate into reducing sugar of 95% amounted to reducing sugar
yield of 20 (wt%) from pre-treated T. suecica was obtained from
saccharification, at temperature: 40°C, pH: 4.5 and [E]/[S] of 0.1
after 72 h of incubation. Hydrolysate obtained from enzymatic
saccharification of pretreated T. suecica biomass was further
fermented into biobutanol using Clostridium saccharoperbutyliticum
as biocatalyst. The results from this study demonstrate a positive
prospect of application of dilute alkaline pre-treatment to enhance
enzymatic saccharification and biobutanol production from
microalgal biomass.
Abstract: In the present work homogeneous silica film on
silicon was fabricated by colloidal silica sol. The silica sol precursor
with uniformly granular particle was derived by the alkaline
hydrolysis of tetraethoxyorthosilicate (TEOS) in presence of glycerol
template. The film was prepared by dip coating process. The
templated hetero-structured silica film was annealed at elevated
temperatures to generate nano- and meso porosity in the film. The
film was subsequently annealed at different temperatures to make it
defect free and abrasion resistant. The sol and the film were
characterized by the measurement of particle size distribution,
scanning electron microscopy, XRD, FTIR spectroscopy,
transmission electron microscopy, atomic force microscopy,
measurement of the refractive index, thermal conductivity and
abrasion resistance. The porosity of the films decreased whereas
refractive index and dielectric constant of it `increased with the
increase in the annealing temperature. The thermal conductivity of
the films increased with the increase in the film thickness. The
developed porous silica film holds strong potential for use in
different areas.
Abstract: The research investigates the effects of super plasticizer and molarity of sodium hydroxide alkaline solution on the workability, microstructure and compressive strength of self compacting geopolymer concrete (SCGC). SCGC is an improved way of concreting execution that does not require compaction and is made by complete elimination of ordinary Portland cement content. The parameters studied were superplasticizer (SP) dosage and molarity of NaOH solution. SCGC were synthesized from low calcium fly ash, activated by combinations of sodium hydroxide and sodium silicate solutions, and by incorporation of superplasticizer for self compactability. The workability properties such as filling ability, passing ability and resistance to segregation were assessed using slump flow, T-50, V-funnel, L-Box and J-ring test methods. It was found that the essential workability requirements for self compactability according to EFNARC were satisfied. Results showed that the workability and compressive strength improved with the increase in superplasticizer dosage. An increase in strength and a decrease in workability of these concrete samples were observed with the increase in molarity of NaOH solution from 8M to 14M. Improvement of interfacial transition zone (ITZ) and micro structure with the increase of SP and increase of concentration from 8M to 12M were also identified.
Abstract: The conventional production of biodiesel from crude
palm oil which contains large amounts of free fatty acids in the
presence of a homogeneous base catalyst confronts the problems of
soap formation and very low yield of biodiesel. To overcome these
problems, free fatty acids must be esterified to their esters in the
presence of an acid catalyst prior to alkaline-catalyzed
transesterification. Sulfated metal oxides are a promising group of
catalysts due to their very high acidity. In this research, aluminadoped
sulfated tin oxide (SO4
2-/Al2O3-SnO2) catalysts were prepared
and used for esterification of free fatty acids in crude palm oil in a
batch reactor. The SO4
2-/Al2O3-SnO2 catalysts were prepared from
different Al precursors. The results showed that different Al
precursors gave different activities of the SO4
2-/Al2O3-SnO2 catalysts.
The esterification of free fatty acids in crude palm oil with methanol
in the presence of SO4
2-/Al2O3-SnO2 catalysts followed first-order
kinetics.
Abstract: Oxyleotris marmorata is considered as
undomesticated fish, and its culture occasionally faces a problem of
food deprivation. The present study aims to evaluate alteration of
hematological indices, blood chemical associated with liver function
during 4 weeks of fasting. A non-linear relationships between fasting
days and hematological parameters (red blood cell number; y = -
0.002x2 + 0.041x + 1.249; R2=0.915, P0.05), mean corpuscular
volume; y = -0.180x2 + 2.183x + 149.61; R2=0.732, P>0.05, mean
corpuscular hemoglobin; y = -0.041x2 + 0.862x + 29.864; R2=0.818,
P>0.05 and mean corpuscular hemoglobin concentration; y = -
0.044x2 + 0.711x + 21.580; R2=0.730, P>0.05) were demonstrated.
Significant change in hematocrit (Ht) during fasting period was
observed. Ht elevated sharply increase at the first weeks of fasting
period. Higher Ht also was detected during week 2-4 of fasting time.
The significant reduction of hepatosomatic index was observed (y = -
0.007x2 - 0.096x + 1.414; R2=0.968, P0.05, serum glutamic oxaloacetic transaminase;
y = 0.005x2 – 0.201x2 + 1.297x + 33.256; R2=1, P0.05). Taken together, prolonged fasting has
deleterious effects on hematological indices, liver mass and enzyme
associated in liver function. The marked adverse effects occurred
after the first week of fasting state.
Abstract: Transesterified vegetable oils (biodiesel) are promising alternative fuel for diesel engines. Used vegetable oils are disposed from restaurants in large quantities. But higher viscosity restricts their direct use in diesel engines. In this study, used cooking oil was dehydrated and then transesterified using an alkaline catalyst. The combustion, performance and emission characteristics of Used Cooking oil Methyl Ester (UCME) and its blends with diesel oil are analysed in a direct injection C.I. engine. The fuel properties and the combustion characteristics of UCME are found to be similar to those of diesel. A minor decrease in thermal efficiency with significant improvement in reduction of particulates, carbon monoxide and unburnt hydrocarbons is observed compared to diesel. The use of transesterified used cooking oil and its blends as fuel for diesel engines will reduce dependence on fossil fuels and also decrease considerably the environmental pollution.