Abstract: The presented paper shows the possibility of using
holographic interferometry for measurement of temperature field in
moving fluids. There are a few methods for identification of velocity
fields in fluids, such us LDA, PIV, hot wire anemometry. It is very
difficult to measure the temperature field in moving fluids. One of the
often used methods is Constant Current Anemometry (CCA), which
is a point temperature measurement method. Data are possibly
acquired at frequencies up to 1000Hz. This frequency should be
limiting factor for using of CCA in fluid when fast change of
temperature occurs. This shortcoming of CCA measurements should
be overcome by using of optical methods such as holographic
interferometry. It is necessary to employ a special holographic setup
with double sensitivity instead of the commonly used Mach-Zehnder
type of holographic interferometer in order to attain the parameters
sufficient for the studied case. This setup is not light efficient like the
Mach-Zehnder type but has double sensitivity. The special technique
of acquiring and phase averaging of results from holographic
interferometry is also presented. The results from the holographic
interferometry experiments will be compared with the temperature
field achieved by methods CCA method.
Abstract: Absorption and fluorescence spectra of quinine
sulphate (QSD) have been recorded at room temperature in wide
range of solvents of different polarities. The ground-state dipole
moment of QSD was obtained from quantum mechanical calculations
and the excited state dipole moment of QSD was estimated from
Bakhshiev-s and Kawski-Chamma-Viallet-s equations by means of
solvatochromic shift method. Higher value of dipole moment is
observed for excited state as compared to the corresponding ground
state value and this is attributed to the more polar excited state of
QSD.
Abstract: The objective of this study was to develop safety practices which is suitable for Thai industrial operators from Incident and Injury Free, IIF to create safety behavior and reduce the un-safe records in the petroleum industry. A number of 310 technicians i.e., 295 males and 15 females, in service maintenance section participated in this program. The safety attitude level and safety behavior level for pre-attended and post-attended the developed safety practices of the technicians were evaluated using questionnaire procedure and on-site observation. After applied the developed practice program, both of the safety attitudes and safety behavior were increased to be at very good level and good level, respectively. Evaluating the follow-up unsafe records, it was found that the injury was reduced from 0.11 to 0 case/month, the medical treatment case was reduced from 0.22 to 0 case/month and the first aid case was reduced from 1 to 0.33 case/month. The developed safety working practice was successfully implemented to Thai industrial operators.
Abstract: The paper proposes a new concept in developing
collaborative design system. The concept framework involves
applying simulation of supply chain management to collaborative
design called – 'SCM–Based Design Tool'. The system is developed
particularly to support design activities and to integrate all facilities
together. The system is aimed to increase design productivity and
creativity. Therefore, designers and customers can collaborate by the
system since conceptual design. JAG: Jewelry Art Generator based
on artificial intelligence techniques is integrated into the system.
Moreover, the proposed system can support users as decision tool
and data propagation. The system covers since raw material supply
until product delivery. Data management and sharing information are
visually supported to designers and customers via user interface. The
system is developed on Web–assisted product development
environment. The prototype system is presented for Thai jewelry
industry as a system prototype demonstration, but applicable for
other industry.
Abstract: This paper provides an overview of auction theory
literature. We present a general review on literature of various
auctions and focus ourselves specifically on an English auction. We
are interested in modelling bidder-s behavior in an English auction
environment. And hence, we present an overview of the New Zealand
wool auction followed by a model that would describe a bidder-s
decision making behavior from the New Zealand wool auction. The
mathematical assumptions in an English auction environment are
demonstrated from the perspective of the New Zealand wool auction.
Abstract: Existing methods in which the animation data of all frames are stored and reproduced as with vertex animation cannot be used in mobile device environments because these methods use large amounts of the memory. So 3D animation data reduction methods aimed at solving this problem have been extensively studied thus far and we propose a new method as follows. First, we find and remove frames in which motion changes are small out of all animation frames and store only the animation data of remaining frames (involving large motion changes). When playing the animation, the removed frame areas are reconstructed using the interpolation of the remaining frames. Our key contribution is to calculate the accelerations of the joints of individual frames and the standard deviations of the accelerations using the information of joint locations in the relevant 3D model in order to find and delete frames in which motion changes are small. Our methods can reduce data sizes by approximately 50% or more while providing quality which is not much lower compared to original animations. Therefore, our method is expected to be usefully used in mobile device environments or other environments in which memory sizes are limited.
Abstract: Steel surface defect detection is essentially one of
pattern recognition problems. Support Vector Machines (SVMs) are
known as one of the most proper classifiers in this application. In this
paper, we introduce a more accurate classification method by using
SVMs as our final classifier of the inspection system. In this scheme,
multiclass classification task is performed based on the "one-againstone"
method and different kernels are utilized for each pair of the
classes in multiclass classification of the different defects.
In the proposed system, a decision tree is employed in the first
stage for two-class classification of the steel surfaces to "defect" and
"non-defect", in order to decrease the time complexity. Based on
the experimental results, generated from over one thousand images,
the proposed multiclass classification scheme is more accurate than
the conventional methods and the overall system yields a sufficient
performance which can meet the requirements in steel manufacturing.
Abstract: This paper focuses on a novel method for semantic
searching and retrieval of information about learning materials.
Metametadata encapsulate metadata instances by using the properties
and attributes provided by ontologies rather than describing learning
objects. A novel metametadata taxonomy has been developed which
provides the basis for a semantic search engine to extract, match and
map queries to retrieve relevant results. The use of ontological views
is a foundation for viewing the pedagogical content of metadata
extracted from learning objects by using the pedagogical attributes
from the metametadata taxonomy. Using the ontological approach
and metametadata (based on the metametadata taxonomy) we present
a novel semantic searching mechanism.These three strands – the
taxonomy, the ontological views, and the search algorithm – are
incorporated into a novel architecture (OMESCOD) which has been
implemented.
Abstract: The purposes of researches - to estimate implicit ethnic attitudes by direct and indirect methods, to determine the accordance of two types measuring, to investigate influence of task type used in an experiment, on the results of measuring, as well as to determine a presence or communication between recent episodic events and chronologic correlations of ethnic attitudes. Method of the implicit measuring - an evaluative priming (EPT) carried out with the use of different SOA intervals, explicit methods of research are G.Soldatova-s types of ethnic identity, G.Soldatova-s index of tolerance, E.Bogardus scale of social distance. During five stages of researches received results open some aspects of implicit measuring, its correlation with the results of self-reports on different SOA intervals, connection of implicit measuring with emotional valence of episodic events of participants and other indexes, presenting a contribution to the decision of implicit measuring application problem for study of different social constructs
Abstract: In MPEG and H.26x standards, to eliminate the
temporal redundancy we use motion estimation. Given that the
motion estimation stage is very complex in terms of computational
effort, a hardware implementation on a re-configurable circuit is
crucial for the requirements of different real time multimedia
applications. In this paper, we present hardware architecture for
motion estimation based on "Full Search Block Matching" (FSBM)
algorithm. This architecture presents minimum latency, maximum
throughput, full utilization of hardware resources such as embedded
memory blocks, and combining both pipelining and parallel
processing techniques. Our design is described in VHDL language,
verified by simulation and implemented in a Stratix II
EP2S130F1020C4 FPGA circuit. The experiment result show that the
optimum operating clock frequency of the proposed design is 89MHz
which achieves 160M pixels/sec.
Abstract: In this contribution a newly developed e-learning environment is presented, which incorporates Intelligent Agents and Computational Intelligence Techniques. The new e-learning environment is constituted by three parts, the E-learning platform Front-End, the Student Questioner Reasoning and the Student Model Agent. These parts are distributed geographically in dispersed computer servers, with main focus on the design and development of these subsystems through the use of new and emerging technologies. These parts are interconnected in an interoperable way, using web services for the integration of the subsystems, in order to enhance the user modelling procedure and achieve the goals of the learning process.
Abstract: techniques are examined to overcome the
performance degradation caused by the channel dispersion using
slow frequency hopping (SFH) with dynamic frequency hopping
(DFH) pattern adaptation. In DFH systems, the frequency slots are
selected by continuous quality monitoring of all frequencies available
in a system and modification of hopping patterns for each individual
link based on replacing slots which its signal to interference ratio
(SIR) measurement is below a required threshold. Simulation results
will show the improvements in BER obtained by DFH in comparison
with matched frequency hopping (MFH), random frequency hopping
(RFH) and multi-carrier code division multiple access (MC-CDMA)
in multipath slowly fading dispersive channels using a generalized
bandpass two-path transfer function model, and will show the
improvement obtained according to the threshold selection.
Abstract: In this article an isotropic linear elastic half-space with
a cylindrical cavity of finite length is considered to be under the
effect of a ring shape time-harmonic torsion force applied at an
arbitrary depth on the surface of the cavity. The equation of
equilibrium has been written in a cylindrical coordinate system. By
means of Fourier cosine integral transform, the non-zero
displacement component is obtained in the transformed domain. With
the aid of the inversion theorem of the Fourier cosine integral
transform, the displacement is obtained in the real domain. With the
aid of boundary conditions, the involved boundary value problem for
the fundamental solution is reduced to a generalized Cauchy singular
integral equation. Integral representation of the stress and
displacement are obtained, and it is shown that their degenerated
form to the static problem coincides with existing solutions in the
literature.
Abstract: The quick training algorithms and accurate solution
procedure for incremental learning aim at improving the efficiency of
training of SVR, whereas there are some disadvantages for them, i.e.
the nonconvergence of the formers for changeable training set and
the inefficiency of the latter for a massive dataset. In order to handle
the problems, a new training algorithm for a changeable training
set, named Approximation Incremental Training Algorithm (AITA),
was proposed. This paper explored the reason of nonconvergence
theoretically and discussed the realization of AITA, and finally
demonstrated the benefits of AITA both on precision and efficiency.
Abstract: We identify clawback triggers from firms- proxy
statements (Form DEF 14A) and use the likelihood of restatements to
proxy for financial reporting quality. Based on a sample of 578 U.S.
firms that voluntarily adopt clawback provisions during 2003-2009,
when restatement-based triggers could be decomposed into two types:
fraud and unintentional error, and we do observe the evidence that
using fraud triggers is associated with high financial reporting quality.
The findings support that fraud triggers can enhance deterrent effect of
clawback provision by establishing a viable disincentive against fraud,
misconduct, and otherwise harmful acts. These results are robust to
controlling for the compensation components, to different sample
specifications and to a number of sensitivity.
Abstract: The friction between two metal surfaces results in a
high frequency noise (squealing) which also occurs during the
braking of wagons with rail brakes in the process of shunting at a
marshalling yard with a hump. At that point the noise level may
exceed 130dB, which is extremely unpleasant for workers and
inhabitants. In our research we developed a new composite material
which does not change braking properties, is capable of taking
extremely high pressure loads, reduces noise and is environmentally
friendly. The noise reduction results had been very good and had
shown a decrease of the high frequency noise almost completely (by
99%) at its source. With our technology we had also reduced general
noise by more than 30dBA.
Abstract: Within this work High Temperature Single Impact
Studies were performed to evaluate deformation mechanisms at
different energy and momentum levels. To show the influence of
different microstructures and hardness levels and their response to
single impacts four different materials were tested at various
temperatures up to 700°C. One carbide reinforced NiCrBSi based
Metal Matrix Composite and three different steels were tested. The
aim of this work is to determine critical energies for fracture
appearance and the materials response at different energy and
momenta levels. Critical impact loadings were examined at elevated
temperatures to limit operating conditions in impact dominated
regimes at elevated temperatures. The investigations on the
mechanisms were performed using different means of microscopy at
the surface and in metallographic cross sections. Results indicate
temperature dependence of the occurrence of cracks in hardphase
rich materials, such as Metal Matrix Composites High Speed Steels
and the influence of different impact momenta at constant energies
on the deformation of different steels.
Abstract: Management Systems are powerful tools for businesses
to manage quality , environmental and occupational health and safety
requirements . where once these systems were considered as stand
alone control mechanisms , industry is now opting to increase the
efficiency of these documented systems through a more integrated
approach . System integration offers a significant step forward, where
there are similarities between system components , reducing
duplication and adminstration costs and increasing efficiency .
At first , this paper reviews integrated management system structure
and its benefits. The second part of this paper focuses on the one
example implementation of such a system at Imam Khomeini
Hospital and in final part of the paper will be discuss outcomes of
that proccess .
Abstract: In this work, we used the single Langmuir probe to
measure the plasma density distribution in an geometrically
asymmetric capacitive coupled plasma discharge system. Because of
the frame structure of powered electrode, the plasma density was not
homogeneous in the discharge volume. It was higher under the frame,
but lower in the centre. Finite element simulation results showed a
good agreement with the experiment results. To increase the electron
density in the central volume and improve the homogeneity of the
plasma, we added an auxiliary electrode, powered by DC voltage, in
the simulation geometry. The simulation results showed that the
auxiliary electrode could alter the potential distribution and improve
the density homogeneity effectively.
Abstract: Wheat prediction was carried out using different meteorological variables together with agro meteorological indices in Ardebil district for the years 2004-2005 & 2005–2006. On the basis of correlation coefficients, standard error of estimate as well as relative deviation of predicted yield from actual yield using different statistical models, the best subset of agro meteorological indices were selected including daily minimum temperature (Tmin), accumulated difference of maximum & minimum temperatures (TD), growing degree days (GDD), accumulated water vapor pressure deficit (VPD), sunshine hours (SH) & potential evapotranspiration (PET). Yield prediction was done two months in advance before harvesting time which was coincide with commencement of reproductive stage of wheat (5th of June). It revealed that in the final statistical models, 83% of wheat yield variability was accounted for variation in above agro meteorological indices.