Abstract: A novel biomass composite inspired from wood porous
structure was manufactured by impregnating vinyl monomer into
wood cellular structure under vacuum conditions, and initiating the
monomer for in situ polymerization through a thermal treatment. The
vacuum condition was studied, and the mechanical properties of the
composite were also tested. SEM observation shows that polymer
generated in the wood porous structure, and strongly interacted with
wood matrix; and the polymer content increased with vacuum value
increasing. FTIR indicates that polymer grafted onto wood matrix,
resulting chemical complex between them. The rate of monomer
loading increased with increasing vacuum value and time, accordance
with rate of polymer loading. The compression strength and modulus
of elasticity linearly increased with the increasing rate of polymer
loading. Results indicate that the novel biomass composite possesses
good mechanical properties capable of applying in the fields of
construction, traffic and so forth.
Abstract: The medical data statistical analysis often requires the
using of some special techniques, because of the particularities of
these data. The principal components analysis and the data clustering
are two statistical methods for data mining very useful in the medical
field, the first one as a method to decrease the number of studied
parameters, and the second one as a method to analyze the
connections between diagnosis and the data about the patient-s
condition. In this paper we investigate the implications obtained from
a specific data analysis technique: the data clustering preceded by a
selection of the most relevant parameters, made using the principal
components analysis. Our assumption was that, using the principal
components analysis before data clustering - in order to select and to
classify only the most relevant parameters – the accuracy of
clustering is improved, but the practical results showed the opposite
fact: the clustering accuracy decreases, with a percentage
approximately equal with the percentage of information loss reported
by the principal components analysis.
Abstract: The use of plastic materials in agriculture causes
serious hazards to the environment. The introduction of biodegradable materials, which can be disposed directly into the soil
can be one possible solution to this problem. In the present research results of experimental tests carried out on biodegradable film
fabricated from natural waste (corn husk) are presented. The film was
characterized by Fourier transform infrared spectroscopy (FTIR),
differential scanning calorimeter (DSC), thermal gravimetric analysis
(TGA) and atomic force microscope (AFM) observation. The film is
shown to be readily degraded within 7-9 months under controlled soil
conditions, indicating a high biodegradability rate. The film
fabricated was use to produce biodegradable pot (BioPot) for
seedlings plantation. The introduction and the expanding use of
biodegradable materials represent a really promising alternative for
enhancing sustainable and environmentally friendly agricultural
activities.
Abstract: Researches on the general rules of temperature field
changing and their effects on the bridge in construction are necessary.
This paper investigated the rules of temperature field changing and its
effects on bridge using onsite measurement and computational
analysis. Guanyinsha Bridge was used as a case study in this research.
The temperature field was simulated in analyses. The effects of certain
boundary conditions such as sun radiance, wind speed, and model
parameters such as heat factor and specific heat on temperature field
are investigated. Recommended values for these parameters are
proposed. The simulated temperature field matches the measured
observations with high accuracy. At the same time, the stresses and
deflections of the bridge computed with the simulated temperature
field matches measured values too. As a conclusion, the temperature
effect analysis of reinforced concrete box girder can be conducted
directly based on the reliable weather data of the concerned area.
Abstract: Slag sample from copper smelting operation in a
water jacket furnace from DRC plant was used. The study intends to
determine the effect of cooling in the extraction of base metals. The
cooling methods investigated were water quenching, air cooling and
furnace cooling. The latter cooling ways were compared to the
original as received slag. It was observed that, the cooling rate of the
slag affected the leaching of base metals as it changed the phase
distribution in the slag and the base metals distribution within the
phases. It was also found that fast cooling of slag prevented
crystallization and produced an amorphous phase that encloses the
base metals. The amorphous slags from the slag dumps were more
leachable in acidic medium (HNO3) which leached 46%Cu, 95% Co,
85% Zn, 92% Pb and 79% Fe with no selectivity at pH0, than in
basic medium (NH4OH). The leachability was vice versa for the
modified slags by quenching in water which leached 89%Cu with a
high selectivity as metal extractions are less than 1% for Co, Zn, Pb
and Fe at ambient temperature and pH12. For the crystallized slags,
leaching of base metals increased with the increase of temperature
from ambient temperature to 60°C and decreased at the higher
temperature of 80°C due to the evaporation of the ammonia solution
used for basic leaching, the total amounts of base metals that were
leached in slow cooled slags were very low compared to the
quenched slag samples.
Abstract: Evapotranspiration (ET) is a major component of the hydrologic cycle and its accurate estimation is essential for hydrological studies. In past, various estimation methods have been developed for different climatological data, and the accuracy of these methods varies with climatic conditions. Reference crop evapotranspiration (ET0) is a key variable in procedures established for estimating evapotranspiration rates of agricultural crops. Values of ET0 are used with crop coefficients for many aspects of irrigation and water resources planning and management. Numerous methods are used for estimating ET0. As per internationally accepted procedures outlined in the United Nations Food and Agriculture Organization-s Irrigation and Drainage Paper No. 56(FAO-56), use of Penman-Monteith equation is recommended for computing ET0 from ground based climatological observations. In the present study, seven methods have been selected for performance evaluation. User friendly software has been developed using programming language visual basic. The visual basic has ability to create graphical environment using less coding. For given data availability the developed software estimates reference evapotranspiration for any given area and period for which data is available. The accuracy of the software has been checked by the examples given in FAO-56.The developed software is a user friendly tool for estimating ET0 under different data availability and climatic conditions.
Abstract: Power line channel is proposed as an alternative for broadband data transmission especially in developing countries like Tanzania [1]. However the channel is affected by stochastic attenuation and deep notches which can lead to the limitation of channel capacity and achievable data rate. Various studies have characterized the channel without giving exactly the maximum performance and limitation in data transfer rate may be this is due to complexity of channel modeling being used. In this paper the channel performance of medium voltage, low voltage and indoor power line channel is presented. In the investigations orthogonal frequency division multiplexing (OFDM) with phase shift keying (PSK) as carrier modulation schemes is considered, for indoor, medium and low voltage channels with typical ten branches and also Golay coding is applied for medium voltage channel. From channels, frequency response deep notches are observed in various frequencies which can lead to reduce the achievable data rate. However, is observed that data rate up to 240Mbps is realized for a signal to noise ratio of about 50dB for indoor and low voltage channels, however for medium voltage a typical link with ten branches is affected by strong multipath and coding is required for feasible broadband data transfer.
Abstract: Heavy metal transfer in soil profiles is a major
environmental concern because even slow transport through the soil
may eventually lead to deterioration of groundwater quality. The use
of sewage sludge and effluents from wastewater treatment plants for
irrigation of agricultural lands is on the rise particularly in peri-urban
area of developing countries. In this study soil samples under sludge
application and wastewater irrigation were studied and soil samples
were collected in the soil profiles from the surface to 100 cm in
depth. For this purpose, three plots were made in a treatment plant in
south of Tehran-Iran. First plot was irrigated just with effluent from
wastewater treatment plant, second plot with simulated heavy metals
concentration equal 50 years irrigation and in third plot sewage
sludge and effluent was used. Trace metals concentration (Cd, Cu)
were determined for soil samples. The results indicate movement of
metals was observed, but the most concentration of metals was found
in topsoil samples. The most of Cadmium concentration was
measured in the topsoil of plot 3, 4.5mg/kg and Maximum cadmium
movement was observed in 0-20 cm. The most concentration of
copper was 27.76mg/kg, and maximum percolation in 0-20 cm.
Metals (Cd, Cu) were measured in leached water. Preferential flow
and metal complexation with soluble organic apparently allow
leaching of heavy metals.
Abstract: A multi-agent type robot for disaster response in calamity scene is proposed in this paper. The proposed grouped rescue robots can perform cooperative reconnaissance and surveillance to achieve a given rescue mission. The multi-agent rescue of dual set robot consists of one master set and three slave units. The research for this rescue robot system is going to detect at harmful environment where human is unreachable, such as the building is infected with virus or the factory has hazardous liquid in effluent. As a dual set robot, with Bluetooth and communication network, the master set can connect with slave units and send information back to computer by wireless and monitor. Therefore, rescuer can be informed the real-time information in a calamity area. Furthermore, each slave robot is able to obstacle avoidance by ultrasonic sensors, and encodes distance and location by compass. The master robot can integrate every devices information to increase the efficiency of prospected and research unknown area.
Abstract: When dealing with safety in structures, the connections between structural components play an important role. Robustness of a structure as a whole depends both on the load- bearing capacity of the structural component and on the structures capacity to resist total failure, even though a local failure occurs in a component or a connection between components. To avoid progressive collapse it is necessary to be able to carry out a design for connections. A connection may be executed with anchors to withstand local failure of the connection in structures built with prefabricated components. For the design of these anchors, a model is developed for connections in structures performed in prefabricated autoclaved aerated concrete components. The design model takes into account the effect of anchors placed close to the edge, which may result in splitting failure. Further the model is developed to consider the effect of reinforcement diameter and anchor depth. The model is analytical and theoretically derived assuming a static equilibrium stress distribution along the anchor. The theory is compared to laboratory test, including the relevant parameters and the model is refined and theoretically argued analyzing the observed test results. The method presented can be used to improve safety in structures or even optimize the design of the connections
Abstract: Recent fifteen years witnessed fast improvements in the field of humanoid robotics. The human-like robot structure is
more suitable to human environment with its supreme obstacle avoidance properties when compared with wheeled service robots.
However, the walking control for bipedal robots is a challenging task
due to their complex dynamics. Stable reference generation plays a very important role in control.
Linear Inverted Pendulum Model (LIPM) and the Zero Moment Point (ZMP) criterion are applied in a number of studies for stable
walking reference generation of biped walking robots. This paper follows this main approach too. We propose a natural and continuous ZMP reference trajectory for a stable and human-like walk. The ZMP reference trajectories move forward under the sole of the support foot when the robot body is supported by a single leg. Robot center of mass trajectory is obtained
from predefined ZMP reference trajectories by a Fourier series
approximation method. The Gibbs phenomenon problem common with Fourier approximations of discontinuous functions is avoided by employing continuous ZMP references. Also, these ZMP reference
trajectories possess pre-assigned single and double support phases,
which are very useful in experimental tuning work.
The ZMP based reference generation strategy is tested via threedimensional
full-dynamics simulations of a 12-degrees-of-freedom
biped robot model. Simulation results indicate that the proposed reference trajectory generation technique is successful.
Abstract: The objective of this experiment was to study of water
relations and chlorophyll in different wheat genotypes and their
correlations with grain and biological yields. 21 genotypes of bread
wheat were compared in a field experiment as randomized complete
blocks design with four replications. The results showed that relative
water deficit, relative water loss, excised leaf water retention, cell
membrane stability, chlorophyll-a, chlorophyll-b, total chlorophyll,
grain yield and biological yield were different significantly among
wheat genotypes, but SPAD-chlorophyll index, relative water content
and chlorophyll florescence were not. Significant correlations were
not observed among above mentioned water relations and
chlorophyll characteristics with grain yield, but there was a positive
and significant correlation between biological yield and grain yield.
Abstract: Retrieval of the surface reflectance is important in the
remotely sensed data analysis to obtain the atmospheric reflectance or
atmospheric correction. The relationship between visible and mid
infrared reflectance over land was investigated and developed in this
study. The surface reflectances of the two visible bands were
measured using a handheld spectroradiometer collected around
Penang Island. In this study, we use the assumption that the 2.1 μm
band is not affected by aerosol and it is transparent to most aerosol
types (except dust). Therefore the satellite observed signal is the
same as the surface signal in 2.1 μm band. The correlation between
the surface reflectance measured by the spectroradiometer in the blue
and red region and the 2.1 μm observed by the satellite has been
established. We investigate five dates of Landsat TM scenes in this
study. The finding obtained by this study indicates that the surface
reflectance can be retrieved from the 2.1 μm band.
Abstract: The periodic mixed convection of a water-copper
nanofluid inside a rectangular cavity with aspect ratio of 3 is
investigated numerically. The temperature of the bottom wall of the
cavity is assumed greater than the temperature of the top lid which
oscillates horizontally with the velocity defined as u = u0 sin (ω t).
The effects of Richardson number, Ri, and volume fraction of
nanoparticles on the flow and thermal behavior of the nanofluid are
investigated. Velocity and temperature profiles, streamlines and
isotherms are presented. It is observed that when Ri < 1, heat transfer
rate is much greater than when Ri > 1. The higher value of Ri
corresponds to a lower value of the amplitude of the oscillation of
Num in the steady periodic state. Moreover, increasing the volume
fraction of the nanoparticles increases the heat transfer rate.
Abstract: The present paper is a case study about exploitation of
Kheir Abad river (Khoozestan, Iran) water resources and the
problems caused by river sediments around the pumping stations.
The weak points and strong points of Boneh Basht pumping station
have been studied by experienced experts, work teams, and
consulting engineers and technical and executive solutions have been
suggested. Therefore, the suggestions of this article are based on the
performed studies and are proposed in order to evaluate the logical
solutions.
Rather complicated processes resulting from the interaction of
water flows and sediments observed at Boneh Basht pumping station
occur at other pumping stations in almost the same way. Therefore,
Boneh Basht pumping station can be selected as a sample (pilot) and
up-to-date theories and experiences can be applied to this station and
the results can be offered to other stations.
Abstract: Learning using labeled and unlabelled data has
received considerable amount of attention in the machine learning
community due its potential in reducing the need for expensive
labeled data. In this work we present a new method for combining
labeled and unlabeled data based on classifier ensembles. The model
we propose assumes each classifier in the ensemble observes the
input using different set of features. Classifiers are initially trained
using some labeled samples. The trained classifiers learn further
through labeling the unknown patterns using a teaching signals that is
generated using the decision of the classifier ensemble, i.e. the
classifiers self-supervise each other. Experiments on a set of object
images are presented. Our experiments investigate different classifier
models, different fusing techniques, different training sizes and
different input features. Experimental results reveal that the proposed
self-supervised ensemble learning approach reduces classification
error over the single classifier and the traditional ensemble classifier
approachs.
Abstract: An experiment was performed in the south of
Morocco in order to evaluate the effect of deficit irrigation by treated
wastewater on chickpea production. We applied six irrigation
treatments on a local variety of chickpea by supplying alternatively
50 or 100% of ETm in a completely randomized design.
We found a highly significant difference between treatments in
terms of biomass production. Drought stress during the vegetative
period showed highest yield with 6.5 t/ha which was more than the
yield obtained for the control (4.9 t/ha). The optimal crop stage in
which deficit irrigation can be applied is the vegetative growth stage,
as the crop has a chance to develop its root system, to be able to
cover the plant needs for water and nutrient supply during the rest of
cycle, and non stress conditions during the flowering and seed filling
stages allow the plant to optimize its photosynthesis and carbon
translocation, therefore increase its productivity.
Abstract: This presentation narrates the comparative analysis of
the dissolution data nimesulide microparticles prepared with
ethylcellulose, hydroxypropyl methylcellulose, chitosan and
Poly(D,L-lactide-co-glycolide) as polymers. The analysis of release
profiles showed that the variations noted in the release behavior of
nimesulide from various microparticulate formulations are due to the
nature of used polymer. In addition, maximum retardation in the
nimesulide release was observed with HPMC (floating particles).
Thus HPMC miacroparticles may be preferably employed for
sustained release dosage form development.
Abstract: This paper considers the design of a motion planner
that will simultaneously accomplish control and motion planning of a
n-link nonholonomic mobile manipulator, wherein, a n-link
holonomic manipulator is coupled with a nonholonomic mobile
platform, within an obstacle-ridden environment. This planner,
derived from the Lyapunov-based control scheme, generates
collision-free trajectories from an initial configuration to a final
configuration in a constrained environment cluttered with stationary
solid objects of different shapes and sizes. We demonstrate the
efficiency of the control scheme and the resulting acceleration
controllers of the mobile manipulator with results through computer
simulations of an interesting scenario.
Abstract: This paper explain about analysis and design a business directory for micro-scale businesses, small and medium enterprises (SMEs). Business Directory, if implemented will facilitate and optimize the access of SMEs to ease suppliers access to marketing. Business Directory will be equipped with the power of geocoding, so each location can be easily viewed SMEs on the map. The map will be constructed by using the functionality of a webbased Google Maps API. The information presented in the form of multimedia that can be more interesting and interactive. The method used to achieve the goal are: observation; interviews; modeling and classifying business directory for SMEs.