Abstract: This paper presents a novel method for inferring the
odor based on neural activities observed from rats- main olfactory
bulbs. Multi-channel extra-cellular single unit recordings were done
by micro-wire electrodes (tungsten, 50μm, 32 channels) implanted in
the mitral/tufted cell layers of the main olfactory bulb of anesthetized
rats to obtain neural responses to various odors. Neural response
as a key feature was measured by substraction of neural firing rate
before stimulus from after. For odor inference, we have developed a
decoding method based on the maximum likelihood (ML) estimation.
The results have shown that the average decoding accuracy is about
100.0%, 96.0%, 84.0%, and 100.0% with four rats, respectively. This
work has profound implications for a novel brain-machine interface
system for odor inference.
Abstract: Lighvan cheese is basically made from sheep milk in
the area of Sahand mountainside which is located in the North West
of Iran. The main objective of this study was to investigate the effect
of enterococci isolated from traditional Lighvan cheese on the quality
of Iranian UF white during ripening. The experimental design was
split plot based on randomized complete blocks, main plots were four
types of starters and subplots were different ripening durations.
Addition of Enterococcus spp. did not significantly (P
Abstract: The angular distribution of Compton scattering of two
quanta originating in the annihilation of a positron with an electron
is investigated as a quantum key distribution (QKD) mechanism in
the gamma spectral range. The geometry of coincident Compton
scattering is observed on the two sides as a way to obtain partially
correlated readings on the quantum channel. We derive the noise
probability density function of a conceptually equivalent prepare
and measure quantum channel in order to evaluate the limits of the
concept in terms of the device secrecy capacity and estimate it at
roughly 1.9 bits per 1 000 annihilation events. The high error rate
is well above the tolerable error rates of the common reconciliation
protocols; therefore, the proposed key agreement protocol by public
discussion requires key reconciliation using classical error-correcting
codes. We constructed a prototype device based on the readily
available monolithic detectors in the least complex setup.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: Entrepreneurs are important for national labour markets and economies in that they contribute significantly to economic growth as well as provide the majority of jobs and create new ones. According to the Global Entrepreneurship Monitor’s “Report on Women and Entrepreneurship”, investment in women’s entrepreneurship is an important way to exponentially increase the impact of new venture creation finding ways to empower women’s participation and success in entrepreneurship are critical for more sustainable and successful economic development. Our results confirm that they are still differences between men and women entrepreneurs The reasons seems to be the lack of specific business skills, the less extensive social network, and the lack of identification patterns among women. Those differences can be explained by the fact that women still have fewer opportunities to make a career. If this is correct, we can predict an increasing proportion of women among entrepreneurs in the next years. Concerning the development of a favorable environment for developing and enhancing women entrepreneurship activities, our results show the insertion in a network and the role of a model doubtless represent elements determining in the choice to launch an entrepreneurship activity, as well as a precious resource for the success of her company.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: Oxidative stress and overwhelming free radicals
associated with diabetes mellitus are likely to be linked with
development of certain complication such as retinopathy,
nephropathy and neuropathy. Treatment of diabetic subjects with
antioxidant may be of advantage in attenuating these complications.
Olive leaf (Oleaeuropaea), has been endowed with many beneficial
and health promoting properties mostly linked to its antioxidant
activity. This study aimed to evaluate the significance of
supplementation of Olive leaves extract (OLE) in reducing oxidative
stress, hyperglycemia and hyperlipidemia in Sterptozotocin (STZ)-
induced diabetic rats. After induction of diabetes, a significant rise in
plasma glucose, lipid profiles except High density lipoproteincholestrol
(HDLc), malondialdehyde (MDA) and significant decrease
of plasma insulin, HDLc and Plasma reduced glutathione GSH as
well as alteration in enzymatic antioxidants was observed in all
diabetic animals. During treatment of diabetic rats with 0.5g/kg body
weight of Olive leaves extract (OLE) the levels of plasma (MDA)
,(GSH), insulin, lipid profiles along with blood glucose and
erythrocyte enzymatic antioxidant enzymes were significantly
restored to establish values that were not different from normal
control rats. Untreated diabetic rats on the other hand demonstrated
persistent alterations in the oxidative stress marker (MDA), blood
glucose, insulin, lipid profiles and the antioxidant parameters. These
results demonstrate that OLE may be of advantage in inhibiting
hyperglycemia, hyperlipidemia and oxidative stress induced by
diabetes and suggest that administration of OLE may be helpful in
the prevention or at least reduced of diabetic complications
associated with oxidative stress.
Abstract: This paper presents a solution for the behavioural
animation of autonomous virtual agent navigation in virtual environments.
We focus on using Dempster-Shafer-s Theory of Evidence
in developing visual sensor for virtual agent. The role of the visual
sensor is to capture the information about the virtual environment
or identifie which part of an obstacle can be seen from the position
of the virtual agent. This information is require for vitual agent to
coordinate navigation in virtual environment. The virual agent uses
fuzzy controller as a navigation system and Fuzzy α - level for
the action selection method. The result clearly demonstrates the path
produced is reasonably smooth even though there is some sharp turn
and also still not diverted too far from the potential shortest path.
This had indicated the benefit of our method, where more reliable
and accurate paths produced during navigation task.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.
Abstract: A mathematical model for the transmission of SARS is developed. In addition to dividing the population into susceptible (high and low risk), exposed, infected, quarantined, diagnosed and recovered classes, we have included a class called untraced. The model simulates the Gompertz curves which are the best representation of the cumulative numbers of probable SARS cases in Hong Kong and Singapore. The values of the parameters in the model which produces the best fit of the observed data for each city are obtained by using a differential evolution algorithm. It is seen that the values for the parameters needed to simulate the observed daily behaviors of the two epidemics are different.
Abstract: This project aims to investigate the potential of
torrefaction to improve the properties of Malaysian palm kernel shell
(PKS) as a solid fuel. A study towards torrefaction of PKS was
performed under various temperature and residence time of 240, 260,
and 280oC and 30, 60, and 90 minutes respectively. The torrefied
PKS was characterized in terms of the mass yield, energy yield,
elemental composition analysis, calorific value analysis, moisture and
volatile matter contents, and ash and fixed carbon contents. The mass
and energy yield changes in the torrefied PKS were observed to
prove that the temperature has more effect compare to residence time
in the torrefaction process. The C content of PKS increases while H
and O contents decrease after torrefaction, which resulted in higher
heating value between 5 to 16%. Meanwhile, torrefaction caused the
ash and fixed carbon content of PKS to increase, and the moisture
and volatile matter to decrease.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: Ice cover County has a significant impact on rivers as it affects with the ice melting capacity which results in flooding, restrict navigation, modify the ecosystem and microclimate. River ices are made up of different ice types with varying ice thickness, so surveillance of river ice plays an important role. River ice types are captured using infrared imaging camera which captures the images even during the night times. In this paper the river ice infrared texture images are analysed using first-order statistical methods and secondorder statistical methods. The second order statistical methods considered are spatial gray level dependence method, gray level run length method and gray level difference method. The performance of the feature extraction methods are evaluated by using Probabilistic Neural Network classifier and it is found that the first-order statistical method and second-order statistical method yields low accuracy. So the features extracted from the first-order statistical method and second-order statistical method are combined and it is observed that the result of these combined features (First order statistical method + gray level run length method) provides higher accuracy when compared with the features from the first-order statistical method and second-order statistical method alone.
Abstract: Nowadays pharmaceutical care departments located in
hospitals are amongst the important pillars of the healthcare system.
The aim of this study was to evaluate quality of hospital drugstores
affiliated with Kermanshah University of Medical Sciences.
In this cross-sectional study a validated questionnaire was used.
The questionnaire was filled in by the one of the researchers in all
seventeen hospital drugstores located in the teaching and nonteaching
hospitals affiliated with Kermanshah University of Medical
Sciences. The results shows that in observed hospitals,24% of
pharmacy environments, 25% of pharmacy store and storage
conditions, 49% of storage procedure, 25% of ordering drugs and
supplies, 73% of receiving supplies (proper procedure are fallowed
for receiving supplies), 35% of receiving supplies (prompt action
taken if deterioration of drugs received is suspected), 23.35% of
drugs delivery to patients and finally 0% of stock cards are used for
proper inventory control have full compliance with standards.
Abstract: Single crystals of Magnesium alloys such as pure Mg,
Mg-1Zn-0.5Y, Mg-0.1Y, and Mg-0.1Ce alloys were successfully
fabricated in this study by employing the modified Bridgman method.
To determine the exact orientation of crystals, pole figure
measurement using X-ray diffraction were carried out on each single
crystal. Hardness and compression tests were conducted followed by
subsequent recrysatllization annealing. Recrystallization kinetics of
Mg alloy single crystals has been investigated. Fabricated single
crystals were cut into rectangular shaped specimen and solution
treated at 400oC for 24 hrs, and then deformed in compression mode
by 30% reduction. Annealing treatment for recrystallization has been
conducted on these cold-rolled plates at temperatures of 300oC for
various times from 1 to 20 mins. The microstructure observation and
hardness measurement conducted on the recrystallized specimens
revealed that static recrystallization of ternary alloy single crystal was
very slow, while recrystallization behavior of binary alloy single
crystals appeared to be very fast.
Abstract: This paper aims at numerically analysing the effect
of an active flow control (AFC) by a vortex generator jet (VGJ)
submerged in a boundary layer via Chimera Grids and Detached-
Eddy Simulation (DES). The performance of DES results are
judged against Reynolds-Averaged Navier-Stokes (RANS) and
compared with the experiments that showed an unsteady vortex
motion downstream of VGJ. Experimental results showed that
the mechanism of embedding logitudinal vortex structure in the
main stream flow is quite effective in increasing the near wall
momentum of separated aircraft wing. In order to simulate such
a flow configuration together with the VGJ, an efficient numerical
approach is required. This requirement is fulfilled by performing
the DES simulation over the flat plate using the DLR TAU Code.
The DES predictions identify the vortex region via smooth hybrid
length scale and predict the unsteady vortex motion observed in
the experiments. The DES results also showed that the sufficient
grid refinement in the vortex region resolves the turbulent scales
downstream of the VGJ, the spatial vortex core postion and nondimensional
momentum coefficient RVx .
Abstract: Agropyron cristatum L. Gaertn. is a native grass of
semiarid region in Iran which is quit resistant to cool and drought
climate and withstand heavy grazing. This species has close
phylogenetic relationship with Triticum and Hordeum. In this
research, the effect of seven different concentrations of growth
regulator 2,4-D on callus production and somatic embryogenesis of
A. cristatum was investigated on Murashige and Skoog medium. The
results showed that the rate of callus, embryo and neomorph were
highest in 1 mg L-1 2,4-D. Callus production was increased in 1 mg
L-1 2,4-D but dramatically decreased at 5.5 and 9 mg L-1 2,4-D. The
somatic embryos were observed at 1 and 4 mg L-1 2,4-D but matured
embryos and plantlet were only occurred at 1 mg L-1 2,4-D. There
were significant differences between 1 mg L-1 2,4-D and other
treatments for producing globular and torpedo embryos, plantlet,
rooted callus and number of roots (p