Abstract: As the remedy used music becomes active and
meditation effect through the music is verified, people take a growing
interest about psychological balance or remedy given by music. From
traditional studies, it is verified that the music of which spectral
envelop varies approximately as 1/f (f is frequency) down to a
frequency of low frequency bandwidth gives psychological balance.
In this paper, we researched signal properties of music which gives
psychological balance. In order to find this, we derived the property
from voice. Music composed by voice shows large value in NCSD.
We confirmed the degree of deference between music by curvature of
normalized cumulative spectral distribution. In the music that gives
psychological balance, the curvature shows high value, otherwise, the
curvature shows low value.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Abstract: Verification of real-time software systems can be
expensive in terms of time and resources. Testing is the main method
of proving correctness but has been shown to be a long and time
consuming process. Everyday engineers are usually unwilling to
adopt formal approaches to correctness because of the overhead
associated with developing their knowledge of such techniques.
Performance modelling techniques allow systems to be evaluated
with respect to timing constraints. This paper describes PARTES, a
framework which guides the extraction of performance models from
programs written in an annotated subset of C.
Abstract: This paper describes the results of an extensive study
and comparison of popular hash functions SHA-1, SHA-256,
RIPEMD-160 and RIPEMD-320 with JERIM-320, a 320-bit hash
function. The compression functions of hash functions like SHA-1
and SHA-256 are designed using serial successive iteration whereas
those like RIPEMD-160 and RIPEMD-320 are designed using two
parallel lines of message processing. JERIM-320 uses four parallel
lines of message processing resulting in higher level of security than
other hash functions at comparable speed and memory requirement.
The performance evaluation of these methods has been done by using
practical implementation and also by using step computation
methods. JERIM-320 proves to be secure and ensures the integrity of
messages at a higher degree. The focus of this work is to establish
JERIM-320 as an alternative of the present day hash functions for the
fast growing internet applications.
Abstract: The present study focuses on methods allowing a convenient and quick calculation of the SIFs in order to predict the static adhesive strength of bonded joints. A new SIF calculation method is proposed, based on the stresses obtained from a FE model at a reference point located in the adhesive layer at equal distance of the free-edge and of the two interfaces. It is shown that, even limiting ourselves to the two main modes, i.e. the opening and the shearing modes, and using the values of the stresses resulting from a low detailed FE model, an efficient calculation of the peeling stress at adhesive-substrate corners can be obtained by this way. The proposed method is interesting in that it can be the basis of a prediction tool that will allow the designer to quickly evaluate the SIFs characterizing a particular application without developing a detailed analysis.
Abstract: Delivering streaming video over wireless is an
important component of many interactive multimedia applications
running on personal wireless handset devices. Such personal devices
have to be inexpensive, compact, and lightweight. But wireless
channels have a high channel bit error rate and limited bandwidth.
Delay variation of packets due to network congestion and the high bit
error rate greatly degrades the quality of video at the handheld
device. Therefore, mobile access to multimedia contents requires
video transcoding functionality at the edge of the mobile network for
interworking with heterogeneous networks and services. Therefore,
to guarantee quality of service (QoS) delivered to the mobile user, a
robust and efficient transcoding scheme should be deployed in
mobile multimedia transporting network. Hence, this paper
examines the challenges and limitations that the video transcoding
schemes in mobile multimedia transporting network face. Then
handheld resources, network conditions and content based mobile
and wireless video transcoding is proposed to provide high QoS
applications. Exceptional performance is demonstrated in the
experiment results. These experiments were designed to verify and
prove the robustness of the proposed approach. Extensive
experiments have been conducted, and the results of various video
clips with different bit rate and frame rate have been provided.
Abstract: In this paper, we studied some properties of geodesic on some open surfaces: Hyperboloid, Paraboloid and Funnel Surface. Geodesic equation in the v-Clairaut parameterization was calculated and reduced to definite integral. Some geodesics on some open surfaces as mention above were classified by Clairaut's relation.
Abstract: Autofluorescence (AF) bronchoscopy is an
established method to detect dysplasia and carcinoma in situ (CIS).
For this reason the “Sotiria" Hospital uses the Karl Storz D-light
system. However, in early tumor stages the visualization is not that
obvious. With the help of a PC, we analyzed the color images we
captured by developing certain tools in Matlab®. We used statistical
methods based on texture analysis, signal processing methods based
on Gabor models and conversion algorithms between devicedependent
color spaces. Our belief is that we reduced the error made
by the naked eye. The tools we implemented improve the quality of
patients' life.
Abstract: Multimedia, as it stands now is perhaps the most
diverse and rich culture around the globe. One of the major needs of
Multimedia is to have a single system that enables people to
efficiently search through their multimedia catalogues. Many
Domain Specific Systems and architectures have been proposed but
up till now no generic and complete architecture is proposed. In this
paper, we have suggested a generic architecture for Multimedia
Database. The main strengths of our architecture besides being
generic are Semantic Libraries to reduce semantic gap, levels of
feature extraction for more specific and detailed feature extraction
according to classes defined by prior level, and merging of two types
of queries i.e. text and QBE (Query by Example) for more accurate
yet detailed results.
Abstract: Urban water management in Australia faces increasing pressure to deal with the challenges of droughts, growing population and the climate change uncertainty. Addressing these challenges is an opportunity to incorporate the parallel goals of sustainable water management and climate change adaptation through holistic, non-technical means. This paper presents case studies from Perth and Sydney which show how despite robust adaptation plans and experience, recent efforts to 'drought proof' cities have focused on supply-side measures (i.e. desalination), rather than rethinking how water is used and managing demand. The trend towards desalination as a climate adaptation measure raises questions about the sustainability of urban water futures in Australia.
Abstract: This paper discusses the cued speech recognition
methods in videoconference. Cued speech is a specific gesture
language that is used for communication between deaf people. We
define the criteria for sentence intelligibility according to answers of
testing subjects (deaf people). In our tests we use 30 sample videos
coded by H.264 codec with various bit-rates and various speed of
cued speech. Additionally, we define the criteria for consonant sign
recognizability in single-handed finger alphabet (dactyl) analogically
to acoustics. We use another 12 sample videos coded by H.264 codec
with various bit-rates in four different video formats. To interpret the
results we apply the standard scale for subjective video quality
evaluation and the percentual evaluation of intelligibility as in
acoustics. From the results we construct the minimum coded bit-rate
recommendations for every spatial resolution.
Abstract: A self-compacting concrete (SCC) is the one that can
be placed in the form and can go through obstructions by its own
weight and without the need of vibration. Since its first development
in Japan in 1988, SCC has gained wider acceptance in Japan, Europe
and USA due to its inherent distinct advantages. Although there are
visible signs of its gradual acceptance in the North Africa through its
limited use in construction, Libya has yet to explore the feasibility
and applicability of SCC in new construction. The contributing
factors to this reluctance appear to be lack of any supportive
evidence of its suitability with local aggregates and the harsh
environmental conditions. The primary aim of this study is to explore
the feasibility of using SCC made with local aggregates of Eastern
Province of Libya by examining its basic properties characteristics.
This research consists of: (i) Development of a suitable mix for SCC
such as the effect of water to cement ratio, limestone and silica fume
that would satisfy the requirements of the plastic state; (ii) Casting of
concrete samples and testing them for compressive strength and unit
weight. Local aggregates, cement, admixtures and industrial waste
materials were used in this research.
The significance of this research lies in its attempt to provide
some performance data of SCC made in the Eastern Province of
Libya so as to draw attention to the possible use of SCC.
Abstract: The objective of this research was to determine the
potency of indigenous acid-aluminium tolerant Bradyrhizobium
japonicum as producer of indole acetic acid (IAA) and applied it as
nitrogen fixation on local soybeans viz Anjasmoro, Tanggamus
(yellow soybean seeds), and Detam (black soybean seed). Three
isolates of acid-aluminium tolerant Bradyrhizobium japonicum (BJ)
were used in this research, i.e. BJ 11 (wt), BJ 11 (19) - BJ 11(wt)
mutant, and USDA 110 as a reference isolate. All of isolates tested to
produce the IAA by using Salkowsky method. Effect of IAA
production by each of B. japonicum was tested on growth pouch and
greenhouse using three varieties of soybean. All isolates could grow
well and produce IAA on yeast mannitol broth (YMB) medium in
the presence of 0.5 mM L-tryptophan. BJ 11 (19) produced the
highest of IAA at 4 days incubation compared to BJ 11 (wt) and
USDA 110. All tested isolates of Bradyrhizobium japonicum have
showed effect on stimulating the formation of root nodules in
soybean varieties grown on Leonard bottle. The concentration of
IAA on root nodules of soybean symbiotic with B. japonicum was
significantly different with control, except on the treatment using
Tanggamus soybean.
Abstract: The purpose of this study is to analyze the cognitive
and travel experience the situation of the tourist attraction of the sport
tourism in Penghu. This study used a questionnaires, the main island
of Taiwan to Penghu in the way of marine sports tourists adopted the
designated convenience sampling method, a total of 1447 valid
questionnaires. After statistical analysis, this study found that: 1.
Tourists to Penghu sports tourism attraction cognitive as “good air
quality, suitable for water activities". 2. Tourists in Penghu's tourism
experience, “Let me taste the delicious specialties and snacks". 3. The
attraction of the sport tourism, travel experience and perceived value
are correlated, and both the perceived value with a high degree of
predictive ability. Based on the findings of this study not only for
Penghu's tourism industry with the unit in charge of the proposed
operating and suggestions for future research to other researchers.
Abstract: The use of buffer thresholds, blocking and adequate
service strategies are well-known techniques for computer networks
traffic congestion control. This motivates the study of series queues
with blocking, feedback (service under Head of Line (HoL) priority
discipline) and finite capacity buffers with thresholds. In this paper,
the external traffic is modelled using the Poisson process and the
service times have been modelled using the exponential distribution.
We consider a three-station network with two finite buffers, for
which a set of thresholds (tm1 and tm2) is defined. This computer
network behaves as follows. A task, which finishes its service at
station B, gets sent back to station A for re-processing with
probability o. When the number of tasks in the second buffer exceeds
a threshold tm2 and the number of task in the first buffer is less than
tm1, the fed back task is served under HoL priority discipline. In
opposite case, for fed backed tasks, “no two priority services in
succession" procedure (preventing a possible overflow in the first
buffer) is applied. Using an open Markovian queuing schema with
blocking, priority feedback service and thresholds, a closed form
cost-effective analytical solution is obtained. The model of servers
linked in series is very accurate. It is derived directly from a twodimensional
state graph and a set of steady-state equations, followed
by calculations of main measures of effectiveness. Consequently,
efficient expressions of the low computational cost are determined.
Based on numerical experiments and collected results we conclude
that the proposed model with blocking, feedback and thresholds can
provide accurate performance estimates of linked in series networks.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: This study aims to explore the relationship between the
disposition effect and herding behavior of investors trading Taiwanese
information technology stocks. This study differs from previous
literature in two aspects. First, in contrast with the earlier studies that
focused on investigating investors’ herding behavior, this study
explores the possibility that the disposition effect drives investors’
herding behavior. Additionally, it takes an in-depth look at the
interdependence between the disposition effect and herding behavior
of investors, including lead-lag relationship and volatility transmission
effect. Empirical results show that investors trading Taiwan’s
information technology stocks exhibit pronounced herding behavior
and that the disposition effect has a great impact on their herding
behavior.
Abstract: A therapeutic success is the aim of any therapeutic
intervention, but a therapeutic failure is the other side of the same
coin. The purpose of this study is to present the activity of a personal
development group, composed of 14 participants (psychologists,
doctors and a priest) registered for a 2 days course of integrative
psychotherapy. The objectives of this study are centred on: the
management of the personal development group breaking moment
realized by the therapist/trainer; the analysis of the trainer’s personal
situation and of some group participants and the brief presentation of
the main work methods applied on participants in the repairing of the
therapeutic relation and in the counter transfer management. The
therapist’s orientation is an integrative one and the demarche realized
includes T.A. techniques, role play, Gestalt and family systemic
psychotherapy. The conclusions obtained represent landmarks for the
future activity within that group and strengthen the therapeutic
relation with the group.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.