Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: In this work we adopt a combination of Laplace
transform and the decomposition method to find numerical solutions
of a system of multi-pantograph equations. The procedure leads to a
rapid convergence of the series to the exact solution after computing a
few terms. The effectiveness of the method is demonstrated in some
examples by obtaining the exact solution and in others by computing
the absolute error which decreases as the number of terms of the series
increases.
Abstract: There are many situations where input feature vectors are incomplete and methods to tackle the problem have been studied for a long time. A commonly used procedure is to replace each missing value with an imputation. This paper presents a method to perform categorical missing data imputation from numerical and categorical variables. The imputations are based on Simpson-s fuzzy min-max neural networks where the input variables for learning and classification are just numerical. The proposed method extends the input to categorical variables by introducing new fuzzy sets, a new operation and a new architecture. The procedure is tested and compared with others using opinion poll data.
Abstract: In this work, we apply the Modified Laplace
decomposition algorithm in finding a numerical solution of Blasius’
boundary layer equation for the flat plate in a uniform stream. The
series solution is found by first applying the Laplace transform to the
differential equation and then decomposing the nonlinear term by the
use of Adomian polynomials. The resulting series, which is exactly the
same as that obtained by Weyl 1942a, was expressed as a rational
function by the use of diagonal padé approximant.
Abstract: We see in the present day scenario that the Global
positioning system (GPS) has been an effective tool to track the
vehicle. However the adverse part of it is that it can only track a
vehicle-s position. Our present work provides a better platform to
track and disable a vehicle using wireless technology. In our system
we embed a microcomputer which monitors the series of automotive
systems like engine, fuel and braking system. The external USB
modem is connected with the microcomputer to provide 24 x 7
internet accesses. The microcomputer is synchronized with the
owner-s multimedia mobile by means of a software tool “REMOTE
DESKTOP". A unique username and password is provided to the
software tool, so that the owner can only access the microcomputer
through the internet on owner-s mobile. The key fact is that our
design is placed such that it is known only to the owner.
Abstract: Recently, in some places, optical-fibre access
networks have been used with GPON technology belonging to
organizations (in most cases public bodies) that act as neutral
operators. These operators simultaneously provide network services
to various telecommunications operators that offer integrated voice,
data and television services. This situation creates new problems
related to quality of service, since the interests of the users are
intermingled with the interests of the operators. In this paper, we
analyse this problem and consider solutions that make it possible to
provide guaranteed quality of service for voice over IP, data services
and interactive digital television.
Abstract: Deaths from cardiovascular diseases have decreased substantially over the past two decades, largely as a result of advances in acute care and cardiac surgery. These developments have produced a growing population of patients who have survived a myocardial infarction. These patients need to be continuously monitored so that the initiation of treatment can be given within the crucial golden hour. The available conventional methods of monitoring mostly perform offline analysis and restrict the mobility of these patients within a hospital or room. Hence the aim of this paper is to design a Portable Cardiac Telemedicine System to aid the patients to regain their independence and return to an active work schedule, there by improving the psychological well being. The portable telemedicine system consists of a Wearable ECG Transmitter (WET) and a slightly modified mobile phone, which has an inbuilt ECG analyzer. The WET is placed on the body of the patient that continuously acquires the ECG signals from the high-risk cardiac patients who can move around anywhere. This WET transmits the ECG to the patient-s Bluetooth enabled mobile phone using blue tooth technology. The ECG analyzer inbuilt in the mobile phone continuously analyzes the heartbeats derived from the received ECG signals. In case of any panic condition, the mobile phone alerts the patients care taker by an SMS and initiates the transmission of a sample ECG signal to the doctor, via the mobile network.
Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: The spatial variation in plant species associated with intercropping is intended to reduce resource competition between species and increase yield potential. A field experiment was carried out on corn (Zea mays L.) and soybean (Glycine max L.) intercropping in a replacement series experiment with weed contamination consist of: weed free, infestation of redroot pigweed, infestation of jimsonweed and simultaneous infestation of redroot pigweed and jimsonweed in Karaj, Iran during 2007 growing season. The experimental design was a randomized complete block in factorial experiment with replicated thrice. Significant (P≤0.05) differences were observed in yield in intercropping. Corn yield was higher in intercropping, but soybean yield was significantly reduced by corn when intercropped. However, total productivity and land use efficiency were high under the intercropping system even in contamination of either species of weeds. Aggressivity of corn relative to soybean revealed the greater competitive ability of corn than soybean. Land equivalent ratio (LER) more than 1 in all treatments attributed to intercropping advantages and was highest in 50: 50 (corn/soybean) in weed free. These findings suggest that intercropping corn and soybean increase total productivity per unit area and improve land use efficiency. Considering the experimental findings, corn-soybean intercropping (50:50) may be recommended for yield advantage, more efficient utilization of resources, and weed suppression as a biological control.
Abstract: In the globalization process, when the struggle for minds and values of the people is taking place, the impact of the virtual space can cause unexpected effects and consequences in the process of adjustment of young people in this world. Their special significance is defined by unconscious influence on the underlying process of meaning and therefore the values preached by them are much more effective and affect both the personal characteristics and the peculiarities of adjustment process. Related to this the challenge is to identify factors influencing the reflection characteristics of virtual subjects and measures their impact on the personal characteristics of the students.
Abstract: This paper focuses upon three such painters working in
France from this time and their representations both of their host
country in which they found themselves displaced, and of their
homeland which they represent through refracted memories from their
new perspective in Europe. What is their representation of France and
China´╝ÅTaiwan? Is it Otherness or an origin?
This paper also attempts to explore the three artists- diasporic lives
and to redefine their transnational identities. Hou Chin-lang, the
significance of his multiple-split images serve to highlight the intricate
relationships between his work and the surrounding family, and to
reveal his identity of his Taiwan “homeland". Yin Xin takes paintings
from the Western canon and subjects them to a process of
transformation through Chinese imagery. In the same period, Lin
Li-ling, transforms the transnational spirit of Yin Xin to symbolic
codes with neutered female bodies and tatoos, thus creates images that
challenge the boundaries of both gender and nationality.
Abstract: In this paper, the details of an experimental method to measure the clamping force value at bolted connections due to application of wrenching torque to tighten the nut have been presented. A simplified bolted joint including a holed plate with a single bolt was considered to carry out the experiments. This method was designed based on Hooke-s law by measuring compressive axial strain of a steel bush placed between the nut and the plate. In the experimental procedure, the values of clamping force were calculated for seven different levels of applied torque, and this process was repeated three times for each level of the torque. Moreover, the effect of lubrication of threads on the clamping value was studied using the same method. In both conditions (dry and lubricated threads), relation between the torque and the clamping force have been displayed in graphs.
Abstract: Bovine viral diarrhea virus (BVDV) can cause lifelong
persistent infection. One reason for the phenomena is attributed to
BVDV infection to placenta tissue. However the mechanisms that
BVDV invades into placenta tissue remain unclear. To clarify the
molecular mechanisms, we investigated the possible means that
BVDV entered into bovine trophoblast cells (TPC). Yeast two-hybrid
system was used to identify proteins extracted from TPC, which
interact with BVDV envelope glycoprotein E2. A PGbkt7-E2 yeast
expression vector and TPC cDNA library were constructed. Through
two rounds of screening, three positive clones were identified.
Sequencing analysis indicated that all the three positive clones
encoded the same protein clathrin. Physical interaction between
clathrin and BVDV E2 protein was further confirmed by
coimmunoprecipitation experiments. This result suggested that the
clathrin might play a critical role in the process of BVDV entry into
placenta tissue and might be a novel antiviral target for preventing
BVDV infection.
Abstract: Road transportation system is the most important
method of transporting the goods. Considering the most suitable
geographical situation of Iran to transport the goods between Europe
and Asia and placement of this country in direction of international
corridors (east- west) , (north-south) and Asian land transport to
infrastructure development “A.L.T.I.D" and Transport corridor
Europe - Caucasus - Asia “T.R.A.C.E.C.A", noticing the security of
road transportation system in this country is so important. In this
paper the main factors of accidents on the roads of Iran are
categorized regarding the rate of accidents occurred. Then apart from
studying the main reasons of accidents of every category, the main
factors of these events are studied and its strategies in Iran are
introduced.
Abstract: This study reports the implementation of Good
Manufacturing Practice (GMP) in a polycarbonate film processing
plant. The implementation of GMP took place with the creation of a
multidisciplinary team. It was carried out in four steps: conduct gap
assessment, create gap closure plan, close gaps, and follow up the
GMP implementation. The basis for the gap assessment is the
guideline for GMP for plastic materials and articles intended for Food
Contact Material (FCM), which was edited by Plastic Europe. The
effective results of the GMP implementation in this study showed
100% completion of gap assessment. The key success factors for
implementing GMP in production process are the commitment,
intention and support of top management.
Abstract: These days people love to travel around the world.
Regardless of their location and time, they especially Muslims still
need to perform their prayers. Normally for travelers, they need to
bring maps, compass and for Muslim, they even have to bring Qibla
pointer when they travel. It is slightly difficult to determine the Qibla
direction and to know the time for each prayer. As the technology
grows, many PDA equip with maps and GPS to locate their location.
In this paper we present a new electronic device called Mobile Qibla
and Prayer Time Finder to locate the Qibla direction and to
determine each prayer time based on the current user-s location using
PDA. This device use PIC microcontroller equipped with digital
compass where it will communicate with PDA using Bluetooth
technology and display the exact Qibla direction and prayer time
automatically at any place in the world. This device is reliable and
accurate in determining the Qibla direction and prayer time.
Abstract: This paper considers the effect of heat generation
proportional l to (T - T∞ )p , where T is the local temperature and T∞
is the ambient temperature, in unsteady free convection flow near the
stagnation point region of a three-dimensional body. The fluid is
considered in an ambient fluid under the assumption of a step change
in the surface temperature of the body. The non-linear coupled partial
differential equations governing the free convection flow are solved
numerically using an implicit finite-difference method for different
values of the governing parameters entering these equations. The
results for the flow and heat characteristics when p ≤ 2 show that
the transition from the initial unsteady-state flow to the final steadystate
flow takes place smoothly. The behavior of the flow is seen
strongly depend on the exponent p.
Abstract: Transport and land use are two systems that are
mutually influenced. Their interaction is a complex process
associated with continuous feedback. The paper examines the
existing land use around an under construction metro station of the
new metro network of Thessaloniki, Greece, through the use of field
investigations, around the station-s predefined location. Moreover,
except from the analytical land use recording, a sampling
questionnaire survey is addressed to several selected enterprises of
the study area. The survey aims to specify the characteristics of the
enterprises, the trip patterns of their employees and clients, as well as
the stated preferences towards the changes the new metro station is
considered to bring to the area. The interpretation of the interrelationships
among selected data from the questionnaire survey takes
place using the method of Principal Components Analysis for
Categorical Data. The followed methodology and the survey-s results
contribute to the enrichment of the relevant bibliography concerning
the way the creation of a new metro station can have an impact on the
land use pattern of an area, by examining the situation before the
operation of the station.