Abstract: Vickers indentation is used to measure the hardness
of materials. In this study, numerical simulation of Vickers
indentation experiment was performed for Diamond like Carbon
(DLC) coated materials. DLC coatings were deposited on stainless
steel 304 substrates with Chromium buffer layer using RF Magnetron
and T-shape Filtered Cathodic Vacuum Arc Dual system The
objective of this research is to understand the elastic plastic
properties, stress strain distribution, ring and lateral crack growth and
propagation, penetration depth of indenter and delamination of
coating from substrate with effect of buffer layer thickness. The
effect of Poisson-s ratio of DLC coating was also analyzed. Indenter
penetration is more in coated materials with thin buffer layer as
compared to thicker one, under same conditions. Similarly, the
specimens with thinner buffer layer failed quickly due to high
residual stress as compared to the coated materials with reasonable
thickness of 200nm buffer layer. The simulation results suggested the
optimized thickness of 200 nm among the prepared specimens for
durable and long service.
Abstract: The present work deals with analyses of the effects
of bearing curvature and non-Newtonian characteristics on the load capacity of an exponential rectangular squeeze film bearing using
Bingham fluids as lubricants. Bingham fluids are characterized by an
yield value and hence the formation of a “rigid" core in the region
between the plates is justified. The flow is confined to the region
between the core and the plates. The shape of the core has been
identified through numerical means. Further, numerical solutions for
the pressure distribution and load carrying capacity of the bearing
for various values of Bingham number and curvature parameter have
been obtained. The effects of bearing curvature and non-Newtonian
characteristics of the lubricant on the bearing performances have been
discussed.
Abstract: Artificial Neural Network (ANN)s can be modeled for
High Energy Particle analysis with special emphasis on shower core
location. The work describes the use of an ANN based system which
has been configured to predict locations of cores of showers in the
range 1010.5 to 1020.5 eV. The system receives density values as
inputs and generates coordinates of shower events recorded for values
captured by 20 core positions and 80 detectors in an area of 100
meters. Twenty ANNs are trained for the purpose and the positions
of shower events optimized by using cooperative ANN learning. The
results derived with variations of input upto 50% show success rates
in the range of 90s.
Abstract: In today-s highly globalised and competitive world
access to information plays key role in having an upper hand between
business rivals. Hence, proper protection of such crucial resource is
core to any modern business. Implementing a successful information
security system is basically centered around three pillars; technical
solution involving both software and hardware, information security
controls to translate the policies and procedure in the system and the
people to implement. This paper shows that a lot needs to be done for
countries adapting information technology to process, store and
distribute information to secure adequately such core resource.
Abstract: This paper aims to study at the use of local knowledge
to develop community self-protection in flood prone residential area,
Ayutthaya Island has been chosen as a case study. This study tries to
examine the strength of local knowledge which is able to develop
community self-protection and cope with flood disaster. In-depth, this
paper focuses on the influence of social network on knowledge
transfer. After conducted the research, authors reviewed the strength
of local knowledge and also mentioned the obstacles of community to
use and also transfer local knowledge. Moreover, the result of the
study revealed that local knowledge is not always transferred by the
strongest-tie social network (family or kinship) as we used to believe.
Surprisingly, local knowledge could be also transferred by the
weaker-tie social network (teacher/ monk) with the better
effectiveness in some knowledge.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.
Abstract: Environmental impact assessment (EIA) is a procedure tool of environmental management for identifying, predicting, evaluating and mitigating the adverse effects of development proposals. EIA reports usually analyze how the amounts or concentrations of pollutants obey the relevant standards. Actually, many analytical tools can deepen the analysis of environmental impacts in EIA reports, such as life cycle assessment (LCA) and environmental risk assessment (ERA). Life cycle impact assessment (LCIA) is one of steps in LCA to introduce the causal relationships among environmental hazards and damage. Incorporating the LCIA concept into ERA as an integrated tool for EIA can extend the focus of the regulatory compliance of environmental impacts to determine of the significance of environmental impacts. Sometimes, when using integrated tools, it is necessary to consider fuzzy situations due to insufficient information; therefore, ERA should be generalized to fuzzy risk assessment (FRA). Finally, the use of the proposed methodology is demonstrated through the study case of the expansion plan of the world-s largest plastics processing factory.
Abstract: In this study, in order to clarify wind-induced
phenomena, especially vertical mixing of density stratification in a
closed water area with floating-leaved plants, we conducted hydraulic
experiments on wind flow characteristics, wind wave characteristics,
entrainment phenomena and turbulent structure by using a wind tunnel
test tank and simulated floating-leaved plants. From the experimental
results of wind flow and wind wave characteristics, we quantified the
impact of the occupancy rate of the plants on their resistance
characteristics. From the experimental results of entrainment
phenomena, we defined the parameter that could explain the
magnitude of mixing between the density stratifications, and
quantified the impact of the occupancy rate on vertical mixing
between stratifications. From the experimental results of the turbulent
structure of the upper layer, we clarified the differences in small-scale
turbulence components at each occupancy rate and quantified the
impact of the occupancy rate on the turbulence characteristics. For a
summary of this study, we theoretically quantified wind-induced
entrainment phenomena in a closed water area with luxuriant growth
of floating-leaved plants. The results indicated that the impact of
luxuriant growth of floating-leaved plants in a closed water body
could be seen in the difference in small-scale fluid characteristics, and
these characteristics could be expressed using the small-scale
turbulent components.
Abstract: An attempt has been made several times to identify
and discuss the U.S. experience on the formation of political nation in
political science. The purpose of this research paper is to identify the
main aspects of the formation of civic identity in the United States
and Kazakhstan, through the identification of similarities and
differences that can get practical application in making decisions of
national policy issues in the context of globalization, as well as to
answer the questions “What should unite the citizens of Kazakhstan
to the nation?" and “What should be the dominant identity: civil or
ethnic (national) one?"
Can Kazakhstan being multiethnic country like America, adopt its
experience in the formation of a civic nation? Since it is believed that
the “multi-ethnic state of the population is a characteristic feature of
most modern countries in the world," it states that “inter-ethnic
integration is one of the most important aspects of the problem of
forming a new social community (metaetnic - Kazakh people,
Kazakh nation" [1].
Abstract: Increase in using internet makes some problems that
one of them is "internet anxiety". Internet anxiety is a type of anxious
that people may feel during surfing internet or using internet for their
educational purpose, blogging or streaming to digital libraries. The
goal of this study is evaluating of internet anxiety among the
management students. In this research Ealy's internet anxiety
questionnaire, consists of positive and negative items, is completed
by 310 participants. According to the findings, about 64.7% of them
were equal or below to mean anxiety score (50). The distribution of
internet anxiety scores was normal and there was no meaningful
difference between men-s and women's anxiety level in this sample.
Results also showed that there is no meaningful difference of internet
anxiety level between different fields of study in Management. This
evaluation will help managers to perform gap analysis between the
existent level and the desired one. Future work would be providing
techniques for abating human anxiety while using internet via human
computer interaction techniques.
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.
Abstract: To measure the thickness of the subcutaneous adipose
tissue layer, a non-invasive optical measurement system (λ=1300 nm)
is introduced. Animal and human subjects are used for the
experiments. The results of human subjects are compared with the data
of ultrasound device measurements, and a high correlation (r=0.94 for
n=11) is observed. There are two modes in the corresponding signals
measured by the optical system, which can be explained by
two-layered and three-layered tissue models. If the target tissue is
thinner than the critical thickness, detected data using diffuse
reflectance method follow the three-layered tissue model, so the data
increase as the thickness increases. On the other hand, if the target
tissue is thicker than the critical thickness, the data follow the
two-layered tissue model, so they decrease as the thickness increases.
Abstract: A high performance clarification system has been
discussed for advanced aqueous reprocessing of FBR spent fuel.
Dissolver residue gives the cause of troubles on the plant operation of
reprocessing. In this study, the new clarification system based on the
hybrid of centrifuge and filtration was proposed to get the high
separation ability of the component of whole insoluble sludge. The
clarification tests of simulated solid species were carried out to
evaluate the clarification performance using small-scale test apparatus
of centrifuge and filter unit. The density effect of solid species on the
collection efficiency was mainly evaluated in the centrifugal
clarification test. In the filtration test using ceramic filter with pore
size of 0.2μm, on the other hand, permeability and filtration rate
were evaluated in addition to the filtration efficiency. As results, it was
evaluated that the collection efficiency of solid species on the new
clarification system was estimated as nearly 100%. In conclusion, the
high clarification performance of dissolver liquor can be achieved by
the hybrid of the centrifuge and filtration system.
Abstract: Today modern simulations solutions in the wind turbine industry have achieved a high degree of complexity and detail in result. Limitations exist when it is time to validate model results against measurements. Regarding Model validation it is of special interest to identify mode frequencies and to differentiate them from the different excitations. A wind turbine is a complex device and measurements regarding any part of the assembly show a lot of noise. Input excitations are difficult or even impossible to measure due to the stochastic nature of the environment. Traditional techniques for frequency analysis or features extraction are widely used to analyze wind turbine sensor signals, but have several limitations specially attending to non stationary signals (Events). A new technique based on autoregresive analysis techniques is introduced here for a specific application, a comparison and examples related to different events in the wind turbine operations are presented.
Abstract: Reasonably priced and well-constructed housing must
be an integral and element supporting a healthy society. The absence
of housing everyone in society can afford negatively affects the
people's health, education, ability to get jobs, develop their
community. Without access to decent housing, economic
development, integration of immigrants and inclusiveness, the society
is negatively impacted. Canada has a sterling record in creating
housing compared to many other nations around the globe. Canadian
housing gets support from a mature and responsive mortgage network
and a top-quality construction industry as well as safe and excellent
quality building materials that are readily available. Yet 1.7 million
Canadian households occupy substandard abodes. During the past
hundred years, Canada's government has made a wide variety of
attempts to provide decent residential facilities every Canadian can
afford. Despite these laudable efforts, today Canada is left with
housing that is inadequate for many Canadians. People who own their
housing are given all kinds of privileges and perks, while people with
relatively low incomes who rent their apartments or houses are
discriminated against.
To help solve these problems, zoning that is based on an
"inclusionary" philosophy is tool developed to help provide people
the affordable residences that they need. No, thirty years after its
introduction, this type of zoning has been shown effective in helping
build and provide Canadians with a houses or apartments they can
afford to pay for. Using this form of zoning can have different results
+depending on where and how it is used. After examining Canadian
affordable housing and four American cases where this type of
zoning was enforced in the USA, this makes various
recommendations for expanding Canadians' access to housing they
can afford.
Abstract: A zero dimensional model has been used to investigate
the combustion performance of a single cylinder direct injection
diesel engine fueled by biofuels with options like supercharging and
exhaust gas recirculation. The numerical simulation was performed at
constant speed. The indicated pressure, temperature diagrams are
plotted and compared for different fuels. The emissions of soot and
nitrous oxide are computed with phenomenological models. The
experimental work was also carried out with biodiesel (palm stearin
methyl ester) diesel blends, ethanol diesel blends to validate
simulation results with experimental results, and observed that the
present model is successful in predicting the engine performance with
biofuels.
Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: Data compression is used operationally to reduce bandwidth and storage requirements. An efficient method for achieving lossless weather radar data compression is presented. The characteristics of the data are taken into account and the optical linear prediction is used for the PPI images in the weather radar data in the proposed method. The next PPI image is identical to the current one and a dramatic reduction in source entropy is achieved by using the prediction algorithm. Some lossless compression methods are used to compress the predicted data. Experimental results show that for the weather radar data, the method proposed in this paper outperforms the other methods.
Abstract: Electronic seal is an electronic device to check the
authenticity and integrity of freight containers at the point of arrival.
While RFID-based eSeals are gaining more acceptances and there are
also some standardization processes for these devices, a recent
research revealed that the current RFID-based eSeals are vulnerable to
various attacks. In this paper, we provide a feasible solution to
enhance the security of active RFID-based eSeals. Our approach is to
use an authentication and key agreement protocol between eSeal and
reader device, enabling data encryption and integrity check. Our
protocol is based on the use of block cipher AES, which is reasonable
since a block cipher can also be used for many other security purposes
including data encryption and pseudo-random number generation. Our
protocol is very simple, and it is applicable to low-end active RFID
eSeals.
Abstract: This paper presents a design method of self-tuning
Quantitative Feedback Theory (QFT) by using improved deadbeat
control algorithm. QFT is a technique to achieve robust control with
pre-defined specifications whereas deadbeat is an algorithm that
could bring the output to steady state with minimum step size.
Nevertheless, usually there are large peaks in the deadbeat response.
By integrating QFT specifications into deadbeat algorithm, the large
peaks could be tolerated. On the other hand, emerging QFT with
adaptive element will produce a robust controller with wider
coverage of uncertainty. By combining QFT-based deadbeat
algorithm and adaptive element, superior controller that is called selftuning
QFT-based deadbeat controller could be achieved. The output
response that is fast, robust and adaptive is expected. Using a grain
dryer plant model as a pilot case-study, the performance of the
proposed method has been evaluated and analyzed. Grain drying
process is very complex with highly nonlinear behaviour, long delay,
affected by environmental changes and affected by disturbances.
Performance comparisons have been performed between the
proposed self-tuning QFT-based deadbeat, standard QFT and
standard dead-beat controllers. The efficiency of the self-tuning QFTbased
dead-beat controller has been proven from the tests results in
terms of controller’s parameters are updated online, less percentage
of overshoot and settling time especially when there are variations in
the plant.