Abstract: Cole-Cole parameters of 40 post-menopausal women
are compared with their DEXA bone mineral density measurements.
Impedance characteristics of four extremities are compared; left and
right extremities are statistically same, but lower extremities are
statistically different than upper ones due to their different fat
content. The correlation of Cole-Cole impedance parameters to bone
mineral density (BMD) is observed to be higher for dominant arm.
With the post-menopausal population, ANOVA tests of the dominant
arm characteristic frequency, as a predictor for DEXA classified
osteopenic and osteoporic population around lumbar spine, is
statistically very significant. When used for total lumbar spine
osteoporosis diagnosis, the area under the Receiver Operating Curve
of the characteristic frequency is 0.830, suggesting that the Cole-Cole
plot characteristic frequency could be a useful diagnostic parameter
when integrated into standard screening methods for osteoporosis.
Moreover, the characteristic frequency can be directly measured by
monitoring frequency driven angular behavior of the dominant arm
without performing any complex calculation.
Abstract: The present study aims to investigate the performance
of Moringa oleifera seed extract as natural coagulant in clarification
of secondary wastewater treatment plant (MWWTP) located in East
of Algiers, Algeria. Coagulation flocculation performance of
Moringa oleifera was evaluated through supernatant residual
turbidity after jar test trials. Various influence parameters namely
Moringa oleifera dosage and pH have been considered. Tests on
Reghaia wastewater, having 129 NTU of initial turbidity, showed a
removal of 69.45% of residual turbidity with only 1.5 mg/l of
Moringa oleifera. This sufficient removal capability encourages the
use of this bioflocculant for treatment of turbid waters. Indeed,
Moringa oleifera which is a natural resource available locally (South
of Algeria) coupled to the non-toxicity, biocompatibility and
biodegradability, may be a very interesting alternative to the
conventional coagulants used so far.
Abstract: This study aimed to explore the practical experience
of child welfare caseworkers and professionalism in child case
management in Malaysia. This paper discussed the specific social
work practice competency and the challenges faced by child
caseworkers in the fieldwork. This research was qualitative with
grounded theory approach. Four sessions of focused group discussion
(FGD) were conducted involving a total of 27 caseworkers (child
protector and probation officers) in the Klang Valley. The study
found that the four basic principles of knowledge in child case
management namely: 1. knowledge in child case management; 2.
professional values of caseworkers towards children; 3. skills in
managing cases; and 4. culturally competent practice in child case
management. In addition, major challenges faced by the child case
manager are the capacity and commitment of the family in children’s
rehabilitation program, the credibility of caseworkers are being
challenged, and the challenges of support system from intra and interagency.
This study is important for policy makers to take into account
the capacity and the needs of the child’s caseworker in accordance
with the national social work competency framework. It is expected
that case management services for children will improve
systematically in line with national standards.
Abstract: Passive control methods can be utilized to build
earthquake resistant structures, and also to strengthen the vulnerable
ones. In this paper, we studied the effect of this system in increasing
the ductility and energy dissipation and also modeled the behavior of
this type of eccentric bracing, and compared the hysteresis diagram
of the modeled samples with the laboratory samples. We studied
several samples of frames with vertical shear-links in order to assess
the behavior of this type of eccentric bracing. Each of these samples
was modeled in finite element software ANSYS 9.0, and was
analyzed under the static cyclic loading. It was found that vertical
shear-links have a more stable hysteresis loops. Another analysis
showed that using honeycomb beams as the horizontal beam along
with steel reinforcement has no negative effect on the hysteresis
behavior of the sample.
Abstract: The current paper presents the results of a conducted
case study. During the past few years the number of children
diagnosed with Learning Difficulties has drastically augmented and
especially the cases of ADHD (Attention Deficit Hyperactivity
Disorder). One of the core characteristics of ADHD is a deficit in
working memory functions. The review of the literature indicates a
plethora of educational software that aim at training and enhancing
the working memory. Nevertheless, in the current paper, the
possibility of using for the same purpose free, online games will be
explored. Another issue of interest is the potential effect of the
working memory training to the core symptoms of ADHD. In order
to explore the abovementioned research questions, three digital tests
are employed, all of which are developed on the E-slate platform by
the author, in order to check the levels of ADHD’s symptoms and to
be used as diagnostic tools, both in the beginning and in the end of
the case study. The tools used during the main intervention of the
research are free online games for the training of working memory.
The research and the data analysis focus on the following axes: a) the
presence and the possible change in two of the core symptoms of
ADHD, attention and impulsivity and b) a possible change in the
general cognitive abilities of the individual. The case study was
conducted with the participation of a thirteen year-old, female
student, diagnosed with ADHD, during after-school hours. The
results of the study indicate positive changes both in the levels of
attention and impulsivity. Therefore, we conclude that the training of
working memory through the use of free, online games has a positive
impact on the characteristics of ADHD. Finally, concerning the
second research question, the change in general cognitive abilities, no
significant changes were noted.
Abstract: Natural dyes are gaining interest due their expected
low risk to human health and to the environment. In this study, the
wash fastness of a natural coloring matter from the liquid waste
produced in the steam treatment of eucalyptus wood in textile fabrics
was investigated. Specifically, eucalyptus wood extract was used to
dye cotton, nylon and wool in an exhaust dyeing process without the
addition of the traditional mordanting agents and then submitted to
wash fastness analysis. The resulting dyed fabrics were evaluated for
color fastness. It was found that wash fastness of dyed fabrics was
very good to cotton and excellent to nylon and wool.
Abstract: Laban Movement Analysis (LMA), developed in the
dance community over the past seventy years, is an effective method
for observing, describing, notating, and interpreting human
movement to enhance communication and expression in everyday
and professional life. Many applications that use motion capture data
might be significantly leveraged if the Laban qualities will be
recognized automatically. This paper presents an automated
recognition method of Laban qualities from motion capture skeletal
recordings and it is demonstrated on the output of Microsoft’s Kinect
V2 sensor.
Abstract: Adequate analgesia following caesarean section
decreases morbidity, hastens ambulation, improves patient outcome
and facilitates care of the newborn. Intrathecal magnesium, an
NMDA antagonist, has been shown to prolong analgesia without
significant side effects in healthy parturients. The aim of this study
was to evaluate the onset and duration of sensory and motor block,
hemodynamic effect, postoperative analgesia, and adverse effects of
magnesium or fentanyl given intrathecally with hyperbaric 0.5%
bupivacaine in patients with mild preeclampsia undergoing caesarean
section. Sixty women with mild preeclampsia undergoing elective
caesarean section were included in a prospective, double blind,
controlled trial. Patients were randomly assigned to receive spinal
anesthesia with 2 mL 0.5% hyperbaric bupivacaine with 12.5 μg
fentanyl (group F) or 0.1 ml of 50% magnesium sulphate (50 mg)
(group M) with 0.15ml preservative free distilled water. Onset,
duration and recovery of sensory and motor block, time to maximum
sensory block, duration of spinal anaesthesia and postoperative
analgesic requirements were studied. Statistical comparison was
carried out using the Chi-square or Fisher’s exact tests and
Independent Student’s t-test where appropriate. The onset of both
sensory and motor block was slower in the magnesium group. The
duration of spinal anaesthesia (246 vs. 284) and motor block (186.3
vs. 210) were significantly longer in the magnesium group. Total
analgesic top up requirement was less in group M. Hemodynamic
parameters were similar in both the groups. Intrathecal magnesium
caused minimal side effects. Since Fentanyl and other opioid
congeners are not available throughout the country easily,
magnesium with its easy availability and less side effect profile can
be a cost effective alternative to fentanyl in managing pregnancy
induced hypertension (PIH) patients given along with Bupivacaine
intrathecally in caesarean section.
Abstract: This paper presents a study on the effect of
second-order slip and jump on forced convection through a long
isothermally heated or cooled planar microchannel. The fully
developed solutions of thermal flow fields are analytically obtained on
the basis of the second-order Maxwell-Burnett slip and Smoluchowski
jump boundary conditions. Results reveal that the second-order term in
the Karniadakis slip boundary condition is found to contribute a
negative velocity slip and then to lead to a higher pressure drop as well
as a higher fluid temperature for the heated-wall case or to a lower
fluid temperature for the cooled-wall case. These findings are contrary
to predictions made by the Deissler model. In addition, the role of
second-order slip becomes more significant when the Knudsen
number increases.
Abstract: The goal of the modern education system is to prepare
students to be able to adapt to ever-changing life situations. They
must be able to acquire required knowledge independently; apply
such knowledge in practice to solve various problems by using
modern technologies; think critically and creatively; competently use
information; be communicative, work in a team; and develop their
own moral values, intellect and cultural awareness. As a result, the
status of education significantly increases; new requirements to its
quality have been formed. In recent years the competency-based
approach in education has become of significant interest. This
approach is a strengthening of applied and practical characteristics of
a school education and leads to the forming of the key students’
competencies which define their success in future life. In this article,
the authors’ attention focuses on a range of key competencies,
educational, informational and communicative and on the possibility
to develop such competencies via STEM education. This research
shows the change in students’ attitude towards scientific disciplines
such as mathematics, general science, technology and engineering as
a result of STEM education. Two staged analyzed questionnaires
completed by students of forms II to IV in the republic of Trinidad
and Tobago allowed the authors to categorize students between two
levels that represent students’ attitude to various disciplines. The
significance of differences between selected levels was confirmed
with the use of Pearson’s chi-squared test. In summary, the analysis
of obtained data makes it possible to conclude that STEM education
has a great potential for development of core students’ competencies
and encourage the development of positive student attitude towards
the above mentioned above scientific disciplines.
Abstract: Twin steel plates-concrete composite shear walls are
composed of a pair of steel plate layers and a concrete layer
sandwiched between them, which have the characteristics of both
reinforced concrete shear walls and steel plate shear walls. Twin steel
plates-composite shear walls contain very high ultimsate bearing
capacity and ductility, which have great potential to be applied in the
super high-rise buildings and special structures. In this paper, we
analyzed the basic characteristics and stress mechanism of the twin
steel plates-composite shear walls. Specifically, we analyzed the
effects of the steel plate thickness, wall thickness and concrete
strength on the bearing capacity of the twin steel plates-composite
shear walls. The analysis results indicate that: (1) the initial shear
stiffness and ultimate shear-carrying capacity is not significantly
affected by the thickness of concrete wall but by the class of concrete,
(2) both factors significantly impact the shear distribution of the
shear walls in ultimate shear-carrying capacity. The technique of twin
steel plates-composite shear walls has been successfully applied in
the construction of an 88-meter Huge Statue of Buddha located in
Hunan Province, China. The analysis results and engineering
experiences showed that the twin steel plates-composite shear walls
have great potential for future research and applications.
Abstract: The right to basic sanitation, was elevated to the
category of fundamental right by the Constitution of 1988 to protect
the ecologically balanced environment, ensuring social rights to
health and adequate housing and put the dignity of the human person
as the foundation of the Brazilian Democratic State. Before their
essentiality to humans, this article seeks to understand why universal
access to basic sanitation is a goal so difficult to achieve in Brazil.
Therefore, this research uses the deductive and analytical method.
Given the nature of the research literature, research techniques were
centered in specialized books on the subject, journals, theses and
dissertations, laws, relevant law case and raising social indicators
relating to the theme. The relevance of the topic stems, among other
things, the fact that sanitation services are essential for a dignified
life, i.e., everyone is entitled to the maintenance of the necessary
existence conditions are satisfied. However, the effectiveness of this
right is undermined in society, since Brazil has huge deficit in
sanitation services, denying thus a worthy life to most of the
population. Thus, it can be seen that the provision of water and
sewage services in Brazil is still characterized by a large imbalance,
since the municipalities with lower population index have greater
disability in the sanitation service. The truth is that the precariousness
of water and sewage services in Brazil is still very concentrated in the
North and Northeast regions, limiting the effective implementation of
the Law 11.445/2007 in the country. Therefore, there is urgent need
for a positive service by the State in the provision of sanitation
services in order to prevent and control disease, improve quality of
life and productivity of individuals, besides preventing contamination
of water resources. More than just social and economic necessity,
there is a government duty to implement such services. In this sense,
given the current scenario, to achieve universal access to basic
sanitation imposes many hurdles. These are mainly in the field of
properly formulated and implemented public policies, i.e., it requires
an excellent institutional organization, management services,
strategic planning, social control, in order to provide answers to
complex challenges.
Abstract: The aim of study was to analyze the functioning the
new model of criminal corporate responsibility in Poland. The need
to introduce into the Polish legal system liability of corporate
(collective entities) has resulted, among others, from the Polish
Republic's international commitments, in particular related to
membership in the European Union. The study showed that responsibility of collective entities under
the Act has a criminal nature. The main question concerns the ability
of the collective entity to be brought to guilt under criminal law
sense. Polish criminal law knows only the responsibility of individual
persons. So far, guilt as a personal feature of action, based on the
ability of the offender to feel in his psyche, could be considered only
in relation to the individual person, while the said Act destroyed this
conviction. Guilt of collective entity must be proven under at least
one of the three possible forms: the guilt in the selection or
supervision and so called organizational guilt. In addition, research in
article has resolved the issue how the principle of proportionality in
relation to criminal measures in response of collective entities should
be considered. It should be remembered that the legal subjectivity of
collective entities, including their rights and freedoms, is an
emanation of the rights and freedoms of individual persons which
create collective entities and through these entities implement their
rights and freedoms. The whole study was proved that the adopted Act largely reflects
the international legal regulations but also contains the unknown and
original legislative solutions.
Abstract: The aim of this study is to investigate the relationship
between expectation, satisfaction and loyalty of South Korean
tourists visiting Turkey. In the research, a questionnaire was used as a
data collecting tool. The questionnaires are filled by South Korean
tourists coming to Turkey through package tours and individual. The
survey was conducted in 2014 in Nevsehir (Cappadocia Region) and
Istanbul. Tourist guides and agency staff have helped the
implementation of surveys. The survey questions are composed of 4
parts, which are “demographic characteristics of tourists”, “travel
behavior characteristics”, “perception of expectations on destination
attributes” and “perception of destination loyalty”. 5-point Likert
type scale including 28 destination attributes was used to measure the
expectations of South Korean tourists coming to Turkey. Questions
were directed to the tourists to measure the destination loyalty. The
questions relating to destination loyalty are “Talking about Turkey to
others”, “Recommendation Turkey to others” and “Tourists’
intentions to revisit Turkey”. The basic hypothesis of the research is
that there is a statistically significant relationship among
expectations, satisfactions and destination loyalty of South Korean
tourists coming to Turkey. The results indicated that the expectation
had a significant effect on overall satisfaction. In addition it was seen
that between overall satisfaction of tourists and destination loyalty
had a significant relationship. Based on findings, some suggestions
for tour operators and travel agencies were made.
Abstract: By enhancing the applicatıon of grounds for
establishment and due to the lack of appropriate sites, engineers
attempt to seek out a new method to reduce the weakness of soils. İn
aspect of economic situation, various ways have been used to
decrease the weak grounds. Because of the rapid development of
infrastructural facilities, spreading the construction operation is an
obligation. Furthermore, in various sites with the really bad soil
situation, engineers have considered obvious problems. One of the
most essential ways for developing the weak soils is stone column.
Obviously, the method was introduced in France in 1830 to improve
a native soil initially. Stone columns have an expanding range of
usage in different rough foundation sites all over the world to
increase the bearing capacity, to reduce the whole and differential
settlements, to enhance the rate of consolidation, to stabilize slopes
stability of embankments and to increase the liquefaction resistance
as well. A recent procedure called installing vertical nails along the
round stone columns in order to make better the performance of
considered columns is offered. Moreover, thanks to the enhancing the
nail diameter, number and embedment nail depth, the positive points
of vertical circumferential nails increases. Based on the result of this
study, load caring capacity will be develop with enhancing the length
and the power of reinforcements in vertical encasement stone column
(CESC). In this study, the main purpose is comparing two methods of
stone columns (installed a nail surrounding the stone columns and
using geogrid on clay) for enhancing the bearing capacity, decreasing
the whole and various settlements.
Abstract: Batch production plants provide a wide range of
scheduling problems. In pharmaceutical industries a batch process
is usually described by a recipe, consisting of an ordering of tasks
to produce the desired product. In this research work we focused
on pharmaceutical production processes requiring the culture of
a microorganism population (i.e. bacteria, yeasts or antibiotics).
Several sources of uncertainty may influence the yield of the culture
processes, including (i) low performance and quality of the cultured
microorganism population or (ii) microbial contamination. For
these reasons, robustness is a valuable property for the considered
application context. In particular, a robust schedule will not collapse
immediately when a cell of microorganisms has to be thrown away
due to a microbial contamination. Indeed, a robust schedule should
change locally in small proportions and the overall performance
measure (i.e. makespan, lateness) should change a little if at all.
In this research work we formulated a constraint programming
optimization (COP) model for the robust planning of antibiotics
production. We developed a discrete-time model with a multi-criteria
objective, ordering the different criteria and performing a
lexicographic optimization. A feasible solution of the proposed
COP model is a schedule of a given set of tasks onto available
resources. The schedule has to satisfy tasks precedence constraints,
resource capacity constraints and time constraints. In particular
time constraints model tasks duedates and resource availability
time windows constraints. To improve the schedule robustness, we
modeled the concept of (a, b) super-solutions, where (a, b) are input
parameters of the COP model. An (a, b) super-solution is one in
which if a variables (i.e. the completion times of a culture tasks)
lose their values (i.e. cultures are contaminated), the solution can be
repaired by assigning these variables values with a new values (i.e.
the completion times of a backup culture tasks) and at most b other
variables (i.e. delaying the completion of at most b other tasks).
The efficiency and applicability of the proposed model is
demonstrated by solving instances taken from a real-life
pharmaceutical company. Computational results showed that
the determined super-solutions are near-optimal.
Abstract: The aim of this work was to characterize a potential
target group of people interested in participating into a training
program in organic farming in the context of mobile-learning. The
information sought addressed in particular, but not exclusively,
possible contents, formats and forms of evaluation that will
contribute to define the course objectives and curriculum, as well as
to ensure that the course meets the needs of the learners and their
preferences. The sample was selected among different European
countries. The questionnaires were delivered electronically for
answering on-line and in the end 135 consented valid questionnaires
were obtained. The results allowed characterizing the target group
and identifying their training needs and preferences towards m-learning
formats, giving valuable tools to design the training offer.
Abstract: The objective of this paper is to evaluate the effects of
soil-structure interaction (SSI) on the modal characteristics and on
the dynamic response of current structures. The objective is on the
overall behaviour of a real structure of five storeys reinforced
concrete (R/C) building typically encountered in Algeria. Sensitivity
studies are undertaken in order to study the effects of frequency
content of the input motion, frequency of the soil-structure system,
rigidity and depth of the soil layer on the dynamic response of such
structures. This investigation indicated that the rigidity of the soil
layer is the predominant factor in soil-structure interaction and its
increases would definitely reduce the deformation in the R/C
structure. On the other hand, increasing the period of the underlying
soil will cause an increase in the lateral displacements at story levels
and create irregularity in the distribution of story shears. Possible
resonance between the frequency content of the input motion and soil
could also play an important role in increasing the structural
response.
Abstract: One of the most critical decision points in the design of a
face recognition system is the choice of an appropriate face representation.
Effective feature descriptors are expected to convey sufficient, invariant
and non-redundant facial information. In this work we propose a set of
Hahn moments as a new approach for feature description. Hahn moments
have been widely used in image analysis due to their invariance, nonredundancy
and the ability to extract features either globally and locally.
To assess the applicability of Hahn moments to Face Recognition we
conduct two experiments on the Olivetti Research Laboratory (ORL)
database and University of Notre-Dame (UND) X1 biometric collection.
Fusion of the global features along with the features from local facial
regions are used as an input for the conventional k-NN classifier. The
method reaches an accuracy of 93% of correctly recognized subjects for
the ORL database and 94% for the UND database.
Abstract: Conductivity properties of DNA molecule is
investigated in a simple, but chemically specific approach that is
intimately related to the Su-Schrieffer-Heeger (SSH) model. This
model is a tight-binding linear nanoscale chain. We have tried to
study the electrical current flowing in DNA and investigated the
characteristic I-V diagram. As a result, It is shown that there are the
(quasi-) ohmic areas in I-V diagram. On the other hand, the regions
with a negative differential resistance (NDR) are detectable in
diagram.