Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: Biodiesel production with used frying by
transesterification reaction with methanol, using a commercial
kaolinite thermally-activated solid acid catalyst was investigated.
The surface area, the average pore diameter and pore volume of the
kaolinite catalyst were 10 m2/g, 13.0 nm and 30 mm3/g, respectively.
The optimal conditions for the transesterification reaction were
determined to be oil/methanol, in a molar ratio 1:31, temperature 160
ºC and catalyst concentration of 3% (w/w). The yield of fatty acids
methyl esters (FAME) was 92.4% after 2 h of reaction. This method
of preparation of biodiesel can be a positive alternative for utilizing
used frying corn oil for feedstock of biodiesel combined with the
inexpensive catalyst.
Abstract: Groundlessness of application probability-statistic methods are especially shown at an early stage of the aviation GTE technical condition diagnosing, when the volume of the information has property of the fuzzy, limitations, uncertainty and efficiency of application of new technology Soft computing at these diagnosing stages by using the fuzzy logic and neural networks methods. It is made training with high accuracy of multiple linear and nonlinear models (the regression equations) received on the statistical fuzzy data basis. At the information sufficiency it is offered to use recurrent algorithm of aviation GTE technical condition identification on measurements of input and output parameters of the multiple linear and nonlinear generalized models at presence of noise measured (the new recursive least squares method (LSM)). As application of the given technique the estimation of the new operating aviation engine D30KU-154 technical condition at height H=10600 m was made.
Abstract: Drilling of glass sheets with different thicknesses have
been carried out by Abrasive Jet Machining process (AJM) in order
to determine its machinability under different controlling parameters
of the AJM process. The present study has been introduced a
mathematical model and the obtained results have been compared
with that obtained from other models published earlier [1-6]. The
experimental results of the present work are used to discuss the
validity of the proposed model as well as the other models.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: Elliptic curve-based certificateless signature is slowly
gaining attention due to its ability to retain the efficiency of
identity-based signature to eliminate the need of certificate
management while it does not suffer from inherent private
key escrow problem. Generally, cryptosystem based on elliptic
curve offers equivalent security strength at smaller key sizes
compared to conventional cryptosystem such as RSA which
results in faster computations and efficient use of computing
power, bandwidth, and storage. This paper proposes to implement
certificateless signature based on bilinear pairing to
structure the framework of IKE authentication. In this paper,
we perform a comparative analysis of certificateless signature
scheme with a well-known RSA scheme and also present the
experimental results in the context of signing and verification
execution times. By generalizing our observations, we discuss the
different trade-offs involved in implementing IKE authentication
by using certificateless signature.
Abstract: This article is devoted to the problems of the
disproportional development of regions in the Republic Kazakhstan.
The threats proceeding from problem regions, make strong impact on
the country-s sustainable development, therefore they are necessary
to be considered at the level of national security.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: In this paper dynamics of a vapour bubble generated
due to a local energy input inside a vertical rigid cylinder and in the
absence of buoyancy forces is investigated. Different ratios of the
diameter of the rigid cylinder to the maximum radius of the bubble
are considered. The Boundary Integral Equation Method is employed
for numerical simulation of the problem. Results show that during
the collapse phase of the bubble inside a vertical rigid cylinder, two
liquid micro jets are developed on the top and bottom sides of the
vapour bubble and are directed inward. Results also show that
existence of a deposit rib inside the vertical rigid cylinder slightly
increases the life time of the bubble. It is found that by increasing the
ratio of the cylinder diameter to the maximum radius of the bubble,
the rate of the growth and collapse phases of the bubble increases
and the life time of the bubble decreases.
Abstract: Since the conception of JML, many tools, applications and implementations have been done. In this context, the users or developers who want to use JML seem surounded by many of these tools, applications and so on. Looking for a common infrastructure and an independent language to provide a bridge between these tools and JML, we developed an approach to embedded contracts in XML for Java: XJML. This approach offer us the ability to separate preconditions, posconditions and class invariants using JML and XML, so we made a front-end which can process Runtime Assertion Checking, Extended Static Checking and Full Static Program Verification. Besides, the capabilities for this front-end can be extended and easily implemented thanks to XML. We believe that XJML is an easy way to start the building of a Graphic User Interface delivering in this way a friendly and IDE independency to developers community wich want to work with JML.
Abstract: This study realizes an empirical investigation of main factors to develop an accounting career, stereotypes on accountants and accounting and perceptions on future career path for a sample of master students in accounting. The research provides some insight into what master students consider when choosing their future career paths. The most important two reasons chosen by students were “career opportunities" and “future earnings. They see accounting as structured, governed by conformity, requiring skills in working with numbers, monotonous, accurate, more efficient than effective but also absorbing, interesting and involving a certain degree of novelty. Although these students plan to start their careers in a multinational or accounting/audit firm, most of those plan to leave after five years. It resulted that women value more flexibility and time requiring special attention in retention policies practiced by firms.
Abstract: The problem of robust disturbance rejection (RDR) using a proportional state feedback controller is studied for the case of Left Invertible MIMO generalized state space linear systems with nonlinear uncertain structure. Sufficient conditions for the problem to have a solution are established. The set of all proportional feedback controllers solving the problem subject to these conditions is analytically determined.
Abstract: One of the main research directions in CAD/CAM
machining area is the reducing of machining time.
The feedrate scheduling is one of the advanced techniques that
allows keeping constant the uncut chip area and as sequel to keep
constant the main cutting force. They are two main ways for feedrate
optimization. The first consists in the cutting force monitoring, which
presumes to use complex equipment for the force measurement and
after this, to set the feedrate regarding the cutting force variation. The
second way is to optimize the feedrate by keeping constant the
material removal rate regarding the cutting conditions.
In this paper there is proposed a new approach using an extended
database that replaces the system model.
The feedrate scheduling is determined based on the identification
of the reconfigurable machine tool, and the feed value determination
regarding the uncut chip section area, the contact length between tool
and blank and also regarding the geometrical roughness.
The first stage consists in the blank and tool monitoring for the
determination of actual profiles. The next stage is the determination
of programmed tool path that allows obtaining the piece target
profile.
The graphic representation environment models the tool and blank
regions and, after this, the tool model is positioned regarding the
blank model according to the programmed tool path. For each of
these positions the geometrical roughness value, the uncut chip area
and the contact length between tool and blank are calculated. Each of
these parameters are compared with the admissible values and
according to the result the feed value is established.
We can consider that this approach has the following advantages:
in case of complex cutting processes the prediction of cutting force is
possible; there is considered the real cutting profile which has
deviations from the theoretical profile; the blank-tool contact length
limitation is possible; it is possible to correct the programmed tool
path so that the target profile can be obtained.
Applying this method, there are obtained data sets which allow the
feedrate scheduling so that the uncut chip area is constant and, as a
result, the cutting force is constant, which allows to use more
efficiently the machine tool and to obtain the reduction of machining
time.
Abstract: The need to implement intelligent highways is much
more emphasized with the growth of vehicle production line as well as vehicle intelligence. The control of intelligent vehicles in order to
reduce human error and boost ease congestion is not accomplished solely by the aid of human resources. The present article is an attempt
to introduce an intelligent control system based on a single central computer. In this project, central computer, without utilizing Global
Positioning System (GPS), is capable of tracking all vehicles, crisis management and control, traffic guidance and recording traffic
crimes along the highway. By the help of RFID technology, vehicles
are connected to computerized systems, intelligent light poles and
other available hardware along the way. By the aid of Wimax
communicative technology, all components of the system are
virtually connected together through local and global networks
devised in them and the energy of the network is provided by the
solar cells installed on the intelligent light poles.
Abstract: This paper proposes a new technique for improving
the efficiency of software testing, which is based on a conventional
attempt to reduce test cases that have to be tested for any given
software. The approach utilizes the advantage of Regression Testing
where fewer test cases would lessen time consumption of the testing
as a whole. The technique also offers a means to perform test case
generation automatically. Compared to one of the techniques in the
literature where the tester has no option but to perform the test case
generation manually, the proposed technique provides a better
option. As for the test cases reduction, the technique uses simple
algebraic conditions to assign fixed values to variables (Maximum,
minimum and constant variables). By doing this, the variables values
would be limited within a definite range, resulting in fewer numbers
of possible test cases to process. The technique can also be used in
program loops and arrays.
Abstract: The main purpose of this study was to determine the predictors of academic achievement of student Information and Communications Technologies (ICT) teachers with different learning styles. Participants were 148 student ICT teachers from Ankara University. Participants were asked to fill out a personal information sheet, the Turkish version of Kolb-s Learning Style Inventory, Weinstein-s Learning and Study Strategies Inventory, Schommer's Epistemological Beliefs Questionnaire, and Eysenck-s Personality Questionnaire. Stepwise regression analyses showed that the statistically significant predictors of the academic achievement of the accommodators were attitudes and high school GPAs; of the divergers was anxiety; of the convergers were gender, epistemological beliefs, and motivation; and of the assimilators were gender, personality, and test strategies. Implications for ICT teaching-learning processes and teacher education are discussed.
Abstract: Hopfield model of associative memory is studied in this work. In particular, two main problems that it possesses: the apparition of spurious patterns in the learning phase, implying the well-known effect of storing the opposite pattern, and the problem of its reduced capacity, meaning that it is not possible to store a great amount of patterns without increasing the error probability in the retrieving phase. In this paper, a method to avoid spurious patterns is presented and studied, and an explanation of the previously mentioned effect is given. Another technique to increase the capacity of a network is proposed here, based on the idea of using several reference points when storing patterns. It is studied in depth, and an explicit formula for the capacity of the network with this technique is provided.
Abstract: This work presents a neural network model for the
clustering analysis of data based on Self Organizing Maps (SOM).
The model evolves during the training stage towards a hierarchical
structure according to the input requirements. The hierarchical structure
symbolizes a specialization tool that provides refinements of the
classification process. The structure behaves like a single map with
different resolutions depending on the region to analyze. The benefits
and performance of the algorithm are discussed in application to the
Iris dataset, a classical example for pattern recognition.
Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: The autonomous mobile robot was designed and implemented which was capable of navigating in the industrial environments and did a job of picking objects from variable height and delivering it to another location following a predefined trajectory. In developing country like Bangladesh industrial robotics is not very prevalent yet, due to the high installation cost. The objective of this project was to develop an autonomous mobile robot for industrial application using the available resources in the local market at lower manufacturing cost. The mechanical system of the robot was comprised of locomotion, gripping and elevation system. Grippers were designed to grip objects of a predefined shape. Cartesian elevation system was designed for vertical movement of the gripper. PIC18F452 microcontroller was the brain of the control system. The prototype autonomous robot was fabricated for relatively lower load than the industry and the performance was tested in a virtual industrial environment created within the laboratory to realize the effectiveness.