Abstract: Many recent electrophysiological studies have
revealed the importance of investigating meditation state in order to
achieve an increased understanding of autonomous control of
cardiovascular functions. In this paper, we characterize heart rate
variability (HRV) time series acquired during meditation using
nonlinear dynamical parameters. We have computed minimum
embedding dimension (MED), correlation dimension (CD), largest
Lyapunov exponent (LLE), and nonlinearity scores (NLS) from HRV
time series of eight Chi and four Kundalini meditation practitioners.
The pre-meditation state has been used as a baseline (control) state to
compare the estimated parameters. The chaotic nature of HRV during
both pre-meditation and meditation is confirmed by MED. The
meditation state showed a significant decrease in the value of CD and
increase in the value of LLE of HRV, in comparison with premeditation
state, indicating a less complex and less predictable nature
of HRV. In addition, it was shown that the HRV of meditation state
is having highest NLS than pre-meditation state. The study indicated
highly nonlinear dynamic nature of cardiac states as revealed by
HRV during meditation state, rather considering it as a quiescent
state.
Abstract: The theoretical investigation is carried out to describe
the effect of increase of pressure waves amplitude in clean and bubbly liquid. The goal of the work is to capture the regime of multiple magnification of acoustic and shock waves in the liquid,
which enables to get appropriate conditions to enlarge collapses of
micro-bubbles. The influence of boundary conditions and frequency
of the governing acoustic field is studied for the case of the
cylindrical acoustic resonator. It has been observed the formation of
standing waves with large amplitude at resonant frequencies. The
interaction of the compression wave with gas and vapor bubbles is
investigated for the convergent channel. It is shown theoretically that
the chemical reactions, which occur inside gas bubbles, provide additional impulse to the wave, that affect strongly on the collapses
of the vapor bubbles
Abstract: This paper in essence presents comparative
experimental data on the mechanical performance of steel and
synthetic fibre-reinforced concrete under compression, tensile split
and flexure. URW1050 steel fibre and HPP45 synthetic fibre, both
with the same concrete design mix, have been used to make cube
specimens for a compression test, cylinders for a tensile split test and
beam specimens for a flexural test. The experimental data
demonstrated steel fibre reinforced concrete to be stronger in flexure
at early stages, whilst both fibre reinforced concrete types displayed
comparatively the same performance in compression, tensile splitting
and 28-day flexural strength. In terms of post-crack controlHPP45
was preferable.
Abstract: Information and communication technology (ICT) is
essential to the operation of business, and create many employment
opportunities. High volumes of students graduate in ICT however
students struggle to find job placement. A discrepancy exists between
graduate skills and industry skill requirements. To address the need
for ICT skills required, universities must create programs to meet the
demands of a changing ICT industry. This requires a partnership
between industry, universities and other stakeholders. This situation
may be viewed as a critical systems thinking problem situation as
there are various role players each with their own needs and
requirements. Jackson states a typical critical systems methods has a
pluralistic nature. This paper explores the applicability and suitability
of Maslow and Dooyeweerd to guide understanding and make
recommendations for change in ICT WIL, to foster an all-inclusive
understanding of the situation by stakeholders. The above methods
provide tools for understanding softer issues beyond the skills
required. The study findings suggest that besides skills requirements,
a deeper understanding and empowering students from being a
student to a professional need to be understood and addressed.
Abstract: Arrack is one of the forms of alcoholic beverage or
liquor which is produced from palm or date juice and commonly
consumed by the lower social class of all religious/ethnic
communities in the north-western villages of Bangladesh. The
purpose of the study was to compare arrack drinking patterns
associated with socio-demographic status among the Muslim, Hindu,
Santal, and Oraon communities in the Rasulpur union of Bangladesh.
A total of 391 respondents (Muslim n-109, Hindu n-103, Santal n-89,
Oraon n-90) selected by cluster random sampling were interviewed
by ADP (Arrack Drinking Pattern) questionnaire. The results of
Pearson Chi-Squire test revealed that arrack drinking patterns were
significantly differed among the Muslim, Hindu, Santal, and Oraon
communities- drinkers. In addition, the results of Spearman-s
bivariate correlation coefficients also revealed that sociodemographic
characteristics of the communities- drinkers were the
significantly positive and negative associations with the arrack
drinking patterns in the Rasulpur union, Bangladesh. The study
suggests that further cross-cultural researches should be conducted
on the consequences of arrack drinking patterns on the communities-
drinkers.
Abstract: The recognition of handwritten numeral is an
important area of research for its applications in post office, banks
and other organizations. This paper presents automatic recognition of
handwritten Kannada numerals based on structural features. Five
different types of features, namely, profile based 10-segment string,
water reservoir; vertical and horizontal strokes, end points and
average boundary length from the minimal bounding box are used in
the recognition of numeral. The effect of each feature and their
combination in the numeral classification is analyzed using nearest
neighbor classifiers. It is common to combine multiple categories of
features into a single feature vector for the classification. Instead,
separate classifiers can be used to classify based on each visual
feature individually and the final classification can be obtained based
on the combination of separate base classification results. One
popular approach is to combine the classifier results into a feature
vector and leaving the decision to next level classifier. This method
is extended to extract a better information, possibility distribution,
from the base classifiers in resolving the conflicts among the
classification results. Here, we use fuzzy k Nearest Neighbor (fuzzy
k-NN) as base classifier for individual feature sets, the results of
which together forms the feature vector for the final k Nearest
Neighbor (k-NN) classifier. Testing is done, using different features,
individually and in combination, on a database containing 1600
samples of different numerals and the results are compared with the
results of different existing methods.
Abstract: In this experiment, we investigated the performance of
two types of heat sink, swaged- and extruded-type, used in the inverter
of industrial electricity generator. The swaged-type heat sink has 62
fins, and the extruded-type has 38 fins having the same dimension as
that of the swaged-type. But the extruded-type heat sink maintains the
same heat transfer area by the laterally waved surface which has 1 mm
in radius. As a result, the swaged- and extruded-type heat sinks
released 71% and 64% of the heat incoming to the heat sink,
respectively. The other incoming heat were naturally convected and
radiated to the ambient. In spite of 40% decrease in number of fins, the
heat release performance of the extruded-type heat sink was lowered
only 7% than that of the swaged-type. We believe that, this shows the
increment of effective heat transfer area by the laterally waved surface
of fins and the better heat transfer property of the extruded-type heat
sink.
Abstract: The deterministic quantum transfer-matrix (QTM)
technique and its mathematical background are presented. This
important tool in computational physics can be applied to a class of
the real physical low-dimensional magnetic systems described by the
Heisenberg hamiltonian which includes the macroscopic molecularbased
spin chains, small size magnetic clusters embedded in some
supramolecules and other interesting compounds. Using QTM, the
spin degrees of freedom are accurately taken into account, yielding
the thermodynamical functions at finite temperatures.
In order to test the application for the susceptibility calculations to
run in the parallel environment, the speed-up and efficiency of
parallelization are analyzed on our platform SGI Origin 3800 with
p = 128 processor units. Using Message Parallel Interface (MPI)
system libraries we find the efficiency of the code of 94% for
p = 128 that makes our application highly scalable.
Abstract: The recycling process of Tungsten alloy (Swarf) by
oxidation reduction technique have been investigated. The reduced
powder was pressed under a pressure 20Kg/cm2 and sintered at
1150°C in dry hydrogen atmosphere. The particle size of the recycled
alloy powder was 1-3 μm and the shape was regular at a reduction
temperature 800°C. The chemical composition of the recycled alloy
is the same as the primary Swarf.
Abstract: This paper presents a recognition system for isolated
words like robot commands. It’s carried out by Time Delay Neural
Networks; TDNN. To teleoperate a robot for specific tasks as turn,
close, etc… In industrial environment and taking into account the
noise coming from the machine. The choice of TDNN is based on its
generalization in terms of accuracy, in more it acts as a filter that
allows the passage of certain desirable frequency characteristics of
speech; the goal is to determine the parameters of this filter for
making an adaptable system to the variability of speech signal and to
noise especially, for this the back propagation technique was used in
learning phase. The approach was applied on commands pronounced
in two languages separately: The French and Arabic. The results for
two test bases of 300 spoken words for each one are 87%, 97.6% in
neutral environment and 77.67%, 92.67% when the white Gaussian
noisy was added with a SNR of 35 dB.
Abstract: High strength concrete (HSC) provides high strength
but lower ductility than normal strength concrete. This low ductility
limits the benefit of using HSC in building safe structures. On the
other hand, when designing reinforced concrete beams, designers
have to limit the amount of tensile reinforcement to prevent the
brittle failure of concrete. Therefore the full potential of the use of
steel reinforcement can not be achieved. This paper presents the idea
of confining concrete in the compression zone so that the HSC will
be in a state of triaxial compression, which leads to improvements in
strength and ductility. Five beams made of HSC were cast and tested.
The cross section of the beams was 200×300 mm, with a length of 4
m and a clear span of 3.6 m subjected to four-point loading, with
emphasis placed on the midspan deflection. The first beam served as
a reference beam. The remaining beams had different tensile
reinforcement and the confinement shapes were changed to gauge
their effectiveness in improving the strength and ductility of the
beams. The compressive strength of the concrete was 85 MPa and the
tensile strength of the steel was 500 MPa and for the stirrups and
helixes was 250 MPa. Results of testing the five beams proved that
placing helixes with different diameters as a variable parameter in the
compression zone of reinforced concrete beams improve their
strength and ductility.
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Niriz
plains in Fars plain were evaluated .Excessive exploitation of
groundwater in this aquifer caused the groundwater levels fall too
fast or to unacceptable levels. The average drawdown of the
groundwater level in this plain were 9.1 meters during 1997 to
2004. The purpose of this study is to evaluate water level changes in
the Niriz Aquifer in the Fars province in order to determine the areas
of greatest depletion, the cause of depletion, and predict the
remaining life of the aquifer.
Abstract: In this study, the use of silicon NAM (Non-Audible
Murmur) microphone in automatic speech recognition is presented.
NAM microphones are special acoustic sensors, which are attached
behind the talker-s ear and can capture not only normal (audible)
speech, but also very quietly uttered speech (non-audible murmur).
As a result, NAM microphones can be applied in automatic speech
recognition systems when privacy is desired in human-machine communication.
Moreover, NAM microphones show robustness against
noise and they might be used in special systems (speech recognition,
speech conversion etc.) for sound-impaired people. Using a small
amount of training data and adaptation approaches, 93.9% word
accuracy was achieved for a 20k Japanese vocabulary dictation
task. Non-audible murmur recognition in noisy environments is also
investigated. In this study, further analysis of the NAM speech has
been made using distance measures between hidden Markov model
(HMM) pairs. It has been shown the reduced spectral space of NAM
speech using a metric distance, however the location of the different
phonemes of NAM are similar to the location of the phonemes
of normal speech, and the NAM sounds are well discriminated.
Promising results in using nonlinear features are also introduced,
especially under noisy conditions.
Abstract: Climate change is a phenomenon has been based on
the available evidence from a very long time ago and now its
existence is very probable. The speed and nature of climate
parameters changes at the middle of twentieth century has been
different and its quickness more than the before and its trend changed
to some extent comparing to the past. Climate change issue now
regarded as not only one of the most common scientific topic but also
a social political one, is not a new issue. Climate change is a
complicated atmospheric oceanic phenomenon on a global scale and
long-term. Precipitation pattern change, fast decrease of snowcovered
resources and its rapid melting, increased evaporation, the
occurrence of destroying floods, water shortage crisis, severe
reduction at the rate of harvesting agricultural products and, so on are
all the significant of climate change. To cope with this phenomenon,
its consequences and events in which public instruction is the most
important but it may be climate that no significant cant and effective
action has been done so far. The present article is included a part of
one surrey about climate change in Fars. The study area having
annually mean temperature 14 and precipitation 320 mm .23 stations
inside the basin with a common 37 year statistical period have been
applied to the meteorology data (1974-2010). Man-kendal and
change factor methods are two statistical methods, applying them, the
trend of changes and the annual mean average temperature and the
annual minimum mean temperature were studied by using them.
Based on time series for each parameter, the annual mean average
temperature and the mean of annual maximum temperature have a
rising trend so that this trend is clearer to the mean of annual
maximum temperature.
Abstract: The performance of mortar subjected to high
temperature and cooled in normal ambient temperature was examined
in the laboratory to comply with the situation of burning & cooling of
a structure. Four series of cubical (5 X 5 X 5 cm) mortar specimens
were made from OPC, and partial replacement (10, 15, 20, 25 &
30%) of OPC by Rice Husk Ash (RHA) produced in the uncontrolled
environment. These specimens were heated in electric furnace to 200,
300, 400, 500 and 7000C. The specimens were kept in normal room
temperature for cooling. They were then tested for mechanical
properties and the results shows that particular 20% RHA mixed
mortar shows better fire performance.
Abstract: In this paper, study on carbonation process of several types of advanced plasters on lime basis is presented. The movement of carbonation head was measured by colorimetric method using phenolphtalein. The rate of carbonation was accessed also by gravimetric method. Samples of studied materials were placed into the climatic chamber for simulation of environment with high concentration of CO2. The particular samples were on all lateral sides and on the bottom side provided by epoxy resin in order to arrange 1-D transport of CO2 into the studied samples. The carbonation rates of particular materials pointed to the time dependence of diffusion process of CO2 for all the studied plasters. From the quantitative point of view, the carbonation of advanced modified plasters was much faster than for the reference lime plaster, what is beneficial for the practical application of the tested newly developed materials.
Abstract: Contamination of heavy metals represents one of the
most pressing threats to water and soil resources as well as human
health. Phytoremediation can be potentially used to remediate metalcontaminated
sites. A major step towards the development of
phytoremediation of heavy metal impacted soils is the discovery of
the heavy metal hyperaccumulation in plants. In this study, the
several established criteria to define a hyperaccumulator plant were
applied. The case study was represented by a mining area in
Hamedan province in the central west part of Iran. Obtained results
showed that the most of sampled species were able to grow on
heavily metal-contaminated soils and also were able to accumulate
extraordinarily high concentrations of some metals such as Zn, Mn,
Cu, Pb and Fe. Using the most common criteria, Euphorbia
macroclada and Centaurea virgata can be classified as
hyperaccumulators of some measured heavy metals and, therefore,
they have suitable potential for phytoremediation of contaminated
soils.
Abstract: Different variants for buoyancy-affected terms in k-ε turbulence model have been utilized to predict the flow parameters more accurately, and investigate applicability of alternative k-ε turbulence buoyant closures in numerical simulation of a horizontal gravity current. The additional non-isotropic turbulent stress due to buoyancy has been considered in production term, based on Algebraic Stress Model (ASM). In order to account for turbulent scalar fluxes, general gradient diffusion hypothesis has been used along with Boussinesq gradient diffusion hypothesis with a variable turbulent Schmidt number and additional empirical constant c3ε.To simulate buoyant flow domain a 2D vertical numerical model (WISE, Width Integrated Stratified Environments), based on Reynolds- Averaged Navier-Stokes (RANS) equations, has been deployed and the model has been further developed for different k-ε turbulence closures. Results are compared against measured laboratory values of a saline gravity current to explore the efficient turbulence model.
Abstract: Knowledge is indispensable but voluminous knowledge becomes a bottleneck for efficient processing. A great challenge for data mining activity is the generation of large number of potential rules as a result of mining process. In fact sometimes result size is comparable to the original data. Traditional data mining pruning activities such as support do not sufficiently reduce the huge rule space. Moreover, many practical applications are characterized by continual change of data and knowledge, thereby making knowledge voluminous with each change. The most predominant representation of the discovered knowledge is the standard Production Rules (PRs) in the form If P Then D. Michalski & Winston proposed Censored Production Rules (CPRs), as an extension of production rules, that exhibit variable precision and supports an efficient mechanism for handling exceptions. A CPR is an augmented production rule of the form: If P Then D Unless C, where C (Censor) is an exception to the rule. Such rules are employed in situations in which the conditional statement 'If P Then D' holds frequently and the assertion C holds rarely. By using a rule of this type we are free to ignore the exception conditions, when the resources needed to establish its presence, are tight or there is simply no information available as to whether it holds or not. Thus the 'If P Then D' part of the CPR expresses important information while the Unless C part acts only as a switch changes the polarity of D to ~D. In this paper a scheme based on Dempster-Shafer Theory (DST) interpretation of a CPR is suggested for discovering CPRs from the discovered flat PRs. The discovery of CPRs from flat rules would result in considerable reduction of the already discovered rules. The proposed scheme incrementally incorporates new knowledge and also reduces the size of knowledge base considerably with each episode. Examples are given to demonstrate the behaviour of the proposed scheme. The suggested cumulative learning scheme would be useful in mining data streams.
Abstract: Automated material handling is given prime
importance in the semi automated and automated facilities since it
provides solution to the gigantic problems related to inventory and
also support the latest philosophies like just in time production JIT
and lean production. Automated storage and retrieval system is an
antidote (if designed properly) to the facility sufferings like getting
the right material , materials getting perished, long cycle times or
many other similar kind of problems. A working model of automated
storage and retrieval system (AS/RS) is designed and developed
under the design parameters specified by Material Handling Industry
of America (MHIA). Later on analysis was carried out to calculate
the throughput and size of the machine. The possible implementation
of this technology in local scenario is also discussed in this paper.