Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: In seismic survey, the information regarding the
velocity of compression wave (Vp) as well as shear wave (Vs) are
very useful especially during the seismic interpretation. Previous
studies showed that both Vp and Vs determined by above methods
are totally different with respect to each other but offered good
approximation. In this study, both Vp and Vs of consolidated granite
rock were studied by using ultrasonic testing method and seismic
refraction method. In ultrasonic testing, two different condition of
rock are used which is dry and wet. The differences between Vp and
Vs getting by using ultrasonic testing and seismic refraction were
investigated and studied. The effect of water content in granite rock
towards the value of Vp and Vs during ultrasonic testing are also
measured. Within this work, the tolerance of the differences between
the velocity of seismic wave getting from ultrasonic testing and the
velocity of seismic wave getting from seismic refraction are also
measured and investigated.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: The objective of the present communication is to
develop new genuine exponentiated mean codeword lengths and to
study deeply the problem of correspondence between well known
measures of entropy and mean codeword lengths. With the help of
some standard measures of entropy, we have illustrated such a
correspondence. In literature, we usually come across many
inequalities which are frequently used in information theory.
Keeping this idea in mind, we have developed such inequalities via
coding theory approach.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: System-level design based on high-level abstractions
is becoming increasingly important in hardware and embedded
system design. This paper analyzes meta-design techniques oriented
at developing meta-programs and meta-models for well-understood
domains. Meta-design techniques include meta-programming and
meta-modeling. At the programming level of design process, metadesign
means developing generic components that are usable in a
wider context of application than original domain components. At the
modeling level, meta-design means developing design patterns that
describe general solutions to the common recurring design problems,
and meta-models that describe the relationship between different
types of design models and abstractions. The paper describes and
evaluates the implementation of meta-design in hardware design
domain using object-oriented and meta-programming techniques.
The presented ideas are illustrated with a case study.
Abstract: A new technique based on Pattern search optimization is proposed for estimating different solar cell parameters in this paper. The estimated parameters are the generated photocurrent, saturation current, series resistance, shunt resistance, and ideality factor. The proposed approach is tested and validated using double diode model to show its potential. Performance of the developed approach is quite interesting which signifies its potential as a promising estimation tool.
Abstract: The recent development of humanoid robots has led robot designers to imagine a great variety of anthropomorphic forms for human-like machine. Which form is the best ? We try to answer this question from a double meaning of the anthropomorphism : a positive anthropomorphism corresponing to the realization of an effective anthropomorphic form object and a negative one corresponding to our natural tendency in certain circumstances to give human attributes to non-human beings. We postulate that any humanoid robot is concerned by both these two anthropomorphism kinds. We propose to use gestalt theory and Heider-s balance theory in order to analyze how negative anthropomorphism can influence our perception of human-like robots. From our theoretical approach we conclude that an “even shape" as defined by gestalt theory is not a sufficient condition for a good integration of future humanoid robots into a human community. Aesthetic perception of the robot cannot be splitted from a social perception : a humanoid robot, any how the efforts made for improving its appearance, could be rejected if it is devoted to a task with too high affective implications.
Abstract: In this paper, a nonlinear model predictive swing-up
and stabilizing sliding controller is proposed for an inverted
pendulum-cart system. In the swing up phase, the nonlinear model
predictive control is formulated as a nonlinear programming problem
with energy based objective function. By solving this problem at
each sampling instant, a sequence of control inputs that optimize the
nonlinear objective function subject to various constraints over a
finite horizon are obtained. Then, this control drives the pendulum to
a predefined neighborhood of the upper equilibrium point, at where
sliding mode based model predictive control is used to stabilize the
systems with the specified constraints. It is shown by the simulations
that, due to the way of formulating the problem, short horizon
lengths are sufficient for attaining the swing up goal.
Abstract: In today-s global and competitive market,
manufacturing companies are working hard towards improving their
production system performance. Most companies develop production
systems that can help in cost reduction. Manufacturing systems
consist of different elements including production methods,
machines, processes, control and information systems. Human issues
are an important part of manufacturing systems, yet most companies
do not pay sufficient attention to them. In this paper, a workforce
planning (WP) model is presented. A non-linear programming model
is developed in order to minimize the hiring, firing, training and
overtime costs. The purpose is to determine the number of workers
for each worker type, the number of workers trained, and the number
of overtime hours. Moreover, a decision support system (DSS) based
on the proposed model is introduced using the Excel-Lingo software
interfacing feature. This model will help to improve the interaction
between the workers, managers and the technical systems in
manufacturing.
Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: A novel path planning approach is presented to solve
optimal path in stochastic, time-varying networks under priori traffic
information. Most existing studies make use of dynamic programming
to find optimal path. However, those methods are proved to
be unable to obtain global optimal value, moreover, how to design
efficient algorithms is also another challenge.
This paper employs a decision theoretic framework for defining
optimal path: for a given source S and destination D in urban transit
network, we seek an S - D path of lowest expected travel time
where its link travel times are discrete random variables. To solve
deficiency caused by the methods of dynamic programming, such as
curse of dimensionality and violation of optimal principle, an integer
programming model is built to realize assignment of discrete travel
time variables to arcs. Simultaneously, pruning techniques are also
applied to reduce computation complexity in the algorithm. The final
experiments show the feasibility of the novel approach.
Abstract: In modern distributed software systems, the issue of communication among composing parts represents a critical point, but the idea of extending conventional programming languages with general purpose communication constructs seems difficult to realize. As a consequence, there is a (growing) gap between the abstraction level required by distributed applications and the concepts provided by platforms that enable communication. This work intends to discuss how the Model Driven Software Development approach can be considered as a mature technology to generate in automatic way the schematic part of applications related to communication, by providing at the same time high level specialized languages useful in all the phases of software production. To achieve the goal, a stack of languages (meta-meta¬models) has been introduced in order to describe – at different levels of abstraction – the collaborative behavior of generic entities in terms of communication actions related to a taxonomy of messages. Finally, the generation of platforms for communication is viewed as a form of specification of language semantics, that provides executable models of applications together with model-checking supports and effective runtime environments.
Abstract: This paper presents a new approach for busbar protection with stable operation of current transformer during saturation, using fuzzy neuro and symmetrical components theory. This technique uses symmetrical components of current signals to learn the hidden relationship existing in the input patterns. Simulation studies are preformed and the influence of changing system parameters such as inception fault and source impedance is studied. Details of the design procedure and the results of performance studies with the proposed relay are given in the paper. An analysis of the performance of the proposed technique during ct saturation conditions is presented. The performance of the technique was investigated for a variety of operating conditions and for several busbar configurations. Data generated by EMTDC simulations of model power systems were used in the investigations. The results indicate that the proposed technique is stable during ct saturation conditions.
Abstract: Electrocardiogram (ECG) is considered to be the
backbone of cardiology. ECG is composed of P, QRS & T waves and
information related to cardiac diseases can be extracted from the
intervals and amplitudes of these waves. The first step in extracting
ECG features starts from the accurate detection of R peaks in the
QRS complex. We have developed a robust R wave detector using
wavelets. The wavelets used for detection are Daubechies and
Symmetric. The method does not require any preprocessing therefore,
only needs the ECG correct recordings while implementing the
detection. The database has been collected from MIT-BIH arrhythmia
database and the signals from Lead-II have been analyzed. MatLab
7.0 has been used to develop the algorithm. The ECG signal under
test has been decomposed to the required level using the selected
wavelet and the selection of detail coefficient d4 has been done based
on energy, frequency and cross-correlation analysis of decomposition
structure of ECG signal. The robustness of the method is apparent
from the obtained results.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: During this day a considerable amount of Leachate is produced with high amounts of organic material and nutrients needed plants. This study has done in order to scrutinize the effect of Leachate compost on the pH, EC and organic matter percentage in the form of statistical Factorial plan through randomizing block design with three main and two minor treatments and also three replications during three six month periods. Major treatments include N: Irrigation with the region-s well water as a control, I: Frequent irrigation with well water and Leachate, C: Mixing Leachate and water well (25 percent leachate + 75 percent ordinary well water) and secondary treatments, include DI: surface drip irrigation and SDI: sub surface drip irrigation. Results of this study indicated significant differences between treatments and also there were mixing up with the control treatment in the reduction of pH, increasing soluble salts and also increasing the organic matter percentage. This increase is proportional to the amount of added Leachate and in the treatment also proportional to higher mixture of frequent treatment. Therefore, since creating an acidic pH increases the ability to absorb some nutrient elements such as phosphorus, iron, zinc, copper and manganese are increased and the other hand, organic materials also improve many physical and chemical properties of soil are used in Leachate trash Consider health issues as refined in the green belts around cities as a liquid fertilizer recommended.
Abstract: the work contains the results of complex investigation
related to the evaluation of condition of working blades of gas turbine
engines during fatigue tests by applying the acoustic emission
method. It demonstrates the possibility of estimating the fatigue
damage of blades in the process of factory tests. The acoustic
emission criteria for detecting and testing the kinetics of fatigue crack
distribution were detected. It also shows the high effectiveness of the
method for non-destructive testing of condition of solid and cooled
working blades for high-temperature gas turbine engines.
Abstract: This study presents the performance of membrane
bioreactor in treating high phosphate wastewater. The laboratory
scale MBR was operated at permeate flux of 25 L/m2.h with a hollow
fiber membrane (polypropylene, approx. pore size 0.01 - 0.2 μm) at
hydraulic retention time (HRT) of 12 hrs. Scanning electron
microscopy (SEM) and energy diffusive X-ray (EDX) analyzer were
used to characterize the membrane foulants. Results showed that the
removal efficiencies of COD, TSS, NH3-N and PO4
3- were 93, 98, 80
and 30% respectively. On average 91% of influent soluble microbial
products (SMP) were eliminated, with the eliminations of
polysaccharides mostly above 80%. The main fouling resistance was
cake resistance. It should be noted that SMP were found in major
portions of mixed liquor that played a relatively significant role in
membrane fouling. SEM and EDX analyses indicated that the
foulants covering the membrane surfaces comprises not only organic
substances but also inorganic elements including Mg, Ca, Al, K and
P.