Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: The changes in quality properties and nutritional
components in two fermented mugworts (Artemisia capillaries
Thumberg, Artemisiaeasiaticae Nakai) were characterized followed
by the rapid pattern analysis of volatile flavor compounds by Electric
Nose based on SAW(Surface Acoustic Wave) sensor in GC system.
There were remarkable decreases in the pH and small changes in the
total soluble solids after fermentation. The L (lightness) and b
(yellowness) values in Hunter's color system were shown to be
decreased, whilst the a (redness) value was increased by fermentation.
The HPLC analysis demonstrated that total amino acids were
increased in quantity and the essential amino acids were contained
higher in A. asiaticaeNakai than in A. capillaries Thumberg. While
the total polyphenol contents were not affected by fermentation, the
total sugar contents were dramatically decreased. Scopoletinwere
highly abundant in A. capillarisThumberg, however, it was not
detected in A. asiaticaeNakai. Volatile flavor compounds by Electric
Nose showed that the intensity of several peaks were increased much
and seven additional flavor peaks were newly produced after
fermentation. The flavor differences of two mugworts were clearly
distinguished from the image patterns of VaporPrintTM which indicate
that the fermentation enables the two mugworts to have subtle flavor
differences.
Abstract: The development of sustainable utilization water resources is crucial. The ecological environment and water resources systems form the foundation of the existence and development of the social economy. The urban ecological support system depends on these resources as well. This research studies the vulnerability, criticality, and risk of climate change on water supply and demand in the main administrative district of the Taijiang Area (Tainan City). Based on the two situations set in this paper and various factors (indexes), this research adopts two kinds of weights (equal and AHP) to conduct the calculation and establish the water supply and demand risk map for the target year 2039. According to the risk analysis result, which is based on equal weight, only one district belongs to a high-grade district (Grade 4). Based on the AHP weight, 16 districts belong to a high-grade or higher-grade district (Grades 4 and 5), and from among them, two districts belong to the highest grade (Grade 5). These results show that the risk level of water supply and demand in cities is higher than that in towns. The government generally gives more attention to the adjustment strategy in the “cities." However, it should also provide proper adjustment strategies for the “towns" to be able to cope with the risks of water supply and demand.
Abstract: There is increasing pressure on, and decline of
mopane woodlands due to increasing use and competition for
mopane resources in Zimbabwe in Namibia. Community management strategies, based largely on local knowledge are
evidently unable to cope. Research has generated potentially useful
information for mopane woodland management, but this information
has not been utilized. The work reported in this paper sought to add value to research work conducted on mopane woodlands by
developing effective community-based mopane woodland
management regimes that were based on both local and scientific
knowledge in Zimbabwe and Namibia. The conditions under which research findings were likely to be adopted for mopane woodland management by communities were investigated. The study was conducted at two sites each in Matobo and Omusati Districts in Zimbabwe and Namibia respectively. The mopane woodland
resources in the two study areas were assessed using scientific
ecological methods. A range of participatory methods was used to collect information on use of mopane woodland resources by communities, institutional arrangements governing access to and use
of these resources and to evaluate scientific knowledge for
applicability in local management regimes. Coppicing, thinning and
pollarding were the research generated management methods evaluated. Realities such as availability of woodland resources and
social roles and responsibilities influenced preferences for woodland
management interventions
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: The purpose of this research is to determine the
knowledge and skills possessed by instructional design (ID)
practitioners in Malaysia. As ID is a relatively new field in the
country and there seems to be an absence of any studies on its
community of practice, the main objective of this research is to
discover the tasks and activities performed by ID practitioners in
educational and corporate organizations as suggested by the
International Board of Standards for Training, Performance and
Instruction. This includes finding out the ID models applied in the
course of their work. This research also attempts to identify the
barriers and issues as to why some ID tasks and activities are rarely
or never conducted. The methodology employed in this descriptive
study was a survey questionnaire sent to 30 instructional designers
nationwide. The results showed that majority of the tasks and
activities are carried out frequently enough but omissions do occur
due to reasons such as it being out of job scope, the decision was
already made at a higher level, and the lack of knowledge and skills.
Further investigations of a qualitative manner should be conducted
to achieve a more in-depth understanding of ID practices in
Malaysia
Abstract: The scope of this research was to study the relation between the facial expressions of three lecturers in a real academic lecture theatre and the reactions of the students to those expressions. The first experiment aimed to investigate the effectiveness of a virtual lecturer-s expressions on the students- learning outcome in a virtual pedagogical environment. The second experiment studied the effectiveness of a single facial expression, i.e. the smile, on the students- performance. Both experiments involved virtual lectures, with virtual lecturers teaching real students. The results suggest that the students performed better by 86%, in the lectures where the lecturer performed facial expressions compared to the results of the lectures that did not use facial expressions. However, when simple or basic information was used, the facial expressions of the virtual lecturer had no substantial effect on the students- learning outcome. Finally, the appropriate use of smiles increased the interest of the students and consequently their performance.
Abstract: Since straightness error of linear motor stage is hardly
dependent upon machining accuracy and assembling accuracy, there is
limit on maximum realizable accuracy. To cope with this limitation,
this paper proposed a servo system to compensate straightness error of
a linear motor stage. The servo system is mounted on the slider of the
linear motor stage and moves in the direction of the straightness error
so as to compensate the error. From position dependency and
repeatability of the straightness error of the slider, a feedforward
compensation control is applied to the platform servo control. In the
consideration of required fine positioning accuracy, a platform driven
by an electro-magnetic actuator is suggested and a sliding mode
control was applied. The effectiveness of the sliding mode control was
verified along with some experimental results.
Abstract: Fermented cassava flours (lafun) sold in Ogun and Oyo
States of Nigeria were collected from 10 markets for a period of two
months and analysed to determine their safety status. The presence of
trace metals was due to high vehicular movement around the drying
sites and markets. Cyanide and moisture contents of samples were
also determined to assess the adequacy of fermentation and drying.
The result showed that sample OWO was found to have the highest
amount of 16.02±0.12mg/kg cyanide while the lowest was found in
sample OJO with 10.51±0.10mg/kg. The results also indicated that
sample TVE had the highest moisture content of 18.50±0.20% while
sample OWO had the lowest amount of 12.46±0.47%. Copper and
lead levels were found to be highest in TVE with values 28.10mg/kg
and 1.1mg/kg respectively, while sample BTS had the lowest values
of 20.6mg/kg and 0.05mg/kg respectively. High value of cyanide
indicated inadequate fermentation.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: Independent component analysis (ICA) is a computational method for finding underlying signals or components from multivariate statistical data. The ICA method has been successfully applied in many fields, e.g. in vision research, brain imaging, geological signals and telecommunications. In this paper, we apply the ICA method to an analysis of mass spectra of oligomeric species emerged from aluminium sulphate. Mass spectra are typically complex, because they are linear combinations of spectra from different types of oligomeric species. The results show that ICA can decomposite the spectral components for useful information. This information is essential in developing coagulation phases of water treatment processes.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: The consumption of lactose in acid cheese whey
anaerobic fermentation process under fed-batch conditions was
studied. During fermentation for 100 hours the biogas production
(CO2 and CH4) was analyzed online. Among the standard analyses
FT-IR spectroscopy was used to follow the consumption of lactose by
bacteria. The absorption bands at 990, 894 and 787 cm-1 in the 2nd
derivative spectra were shown to be characteristic for lactose and
were used to follow the lactose conversion. It was shown that acid
cheese whey lactose was converted by bacteria in first 7 hours. In the
spectra of 17, 18 and 95 hour fermentation samples lactose was not
identified and these results correlated with the HPLC data.
Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: In this paper the combination of thermal oxidation and
electrochemical anodizing processes is used to produce titanium
oxide layers. The response of titanium alloy Ti6Al4V to oxidation
processes at various temperatures and electrochemical anodizing in
various voltages are investigated. Scanning electron microscopy
(SEM); X-Ray Diffraction (XRD) and porosity determination have
been used to characterize the oxide layer thickness, surface
morphology, oxide layer-substrate adhesion and porosity. In the first
experiment, samples modified by thermal oxidation process then
followed by electrochemical anodizing. Second experiment consists
of surfaces modified by electrochemical anodizing process and then
followed by thermal oxidation. The first method shows better
properties than other one. In second experiment, Surfaces modified
were achieved by thicker and more adherent thick oxide layers on
titanium surface. The existence of an electrochemical anodized oxide
layer did not improve the adhesion of thermal oxide layer. The high
temperature, thermal formation of an oxide layer leads to a coarse
oxide grain morphology and a complete oxidative particle. In
addition, in high temperature oxidation porosity content is increased.
The oxide layer of thermal oxidation and electrochemical anodizing
processes; on Ti–6Al–4V substrate was covered with different
colored oxide layers.
Abstract: Primary studies are being carried out in Turkey for
expanding information and communication technologies (ICT) aided instruction activities. Subject of the present study is to identify
whether those studies achieved their goals in the application. Information technologies (IT) formative teachers in the primary
schools, and academicians in the faculties of education were interviewed to investigate the process and results of implementing
computer-aided instruction methods whose basis is strengthened in theory. Analysis of the results gained from two separate surveys
demonstrated that capability of the teachers in elementary education institutions for carrying into effect computer-aided instruction and
technical infrastructure has not been established for computer-aided instruction practices yet. Prospective teachers must be well-equipped in ICT to duly fulfill requirements of modern education and also
must be self-confident. Finally, scope and intensity of the courses given in connection with teaching of the ICT in faculties of education needs to be revised.
Abstract: Luneberg lens is a new generation of antennas that is
developed in the last few years and inserts itself strongly in
Microwaves, Communications and Telescopes area. The idea of this
research is to improve the radiation pattern by decreasing the side
lobes and increasing the main lobe. The new design is proposed to
work in the X-band. The simulated result and analysis are presented.