Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: Using 1km grid datasets representing monthly mean
precipitation, monthly mean temperature, and dry matter production
(DMP), we considered the regional plant production ability in
Southeast and South Asia, and also employed pixel-by-pixel
correlation analysis to assess the intensity of relation between climate
factors and plant production. While annual DMP in South Asia was
approximately less than 2,000kg, the one in most part of Southeast
Asia exceeded 2,500 - 3,000kg. It suggested that plant production in
Southeast Asia was superior to South Asia, however, Rain-Use
Efficiency (RUE) representing dry matter production per 1mm
precipitation showed that inland of Indochina Peninsula and India
were higher than islands in Southeast Asia. By the results of
correlation analysis between climate factors and DMP, while the area
in most parts of Indochina Peninsula indicated negative correlation
coefficients between DMP and precipitation or temperature, the area
in Malay Peninsula and islands showed negative correlation to
precipitation and positive one to temperature, and most part of India
dominating South Asia showed positive to precipitation and negative
to temperature. In addition, the areas where the correlation coefficients
exceeded |0.8| were regarded as “susceptible" to climate factors, and
the areas smaller than |0.2| were “insusceptible". By following the
discrimination, the map implying expected impacts by climate change
was provided.
Abstract: Voice over Internet Protocol (VoIP) application or commonly known as softphone has been developing an increasingly large market in today-s telecommunication world and the trend is expected to continue with the enhancement of additional features. This includes leveraging on the existing presence services, location and contextual information to enable more ubiquitous and seamless communications. In this paper, we discuss the concept of seamless session transfer for real-time application such as VoIP and IPTV, and our prototype implementation of such concept on a selected open source VoIP application. The first part of this paper is about conducting performance evaluation and assessments across some commonly found open source VoIP applications that are Ekiga, Kphone, Linphone and Twinkle so as to identify one of them for implementing our design of seamless session transfer. Subjective testing has been carried out to evaluate the audio performance on these VoIP applications and rank them according to their Mean Opinion Score (MOS) results. The second part of this paper is to discuss on the performance evaluations of our prototype implementation of session transfer using Linphone.
Abstract: This paper gives an introduction to Web mining, then
describes Web Structure mining in detail, and explores the data
structure used by the Web. This paper also explores different Page
Rank algorithms and compare those algorithms used for Information
Retrieval. In Web Mining, the basics of Web mining and the Web
mining categories are explained. Different Page Rank based
algorithms like PageRank (PR), WPR (Weighted PageRank), HITS
(Hyperlink-Induced Topic Search), DistanceRank and DirichletRank
algorithms are discussed and compared. PageRanks are calculated for
PageRank and Weighted PageRank algorithms for a given hyperlink
structure. Simulation Program is developed for PageRank algorithm
because PageRank is the only ranking algorithm implemented in the
search engine (Google). The outputs are shown in a table and chart
format.
Abstract: In this paper, we present a robust and secure
algorithm for watermarking, the watermark is first transformed into
the frequency domain using the discrete wavelet transform (DWT).
Then the entire DWT coefficient except the LL (Band) discarded,
these coefficients are permuted and encrypted by specific mixing.
The encrypted coefficients are inserted into the most significant
spectral components of the stego-image using a chaotic system. This
technique makes our watermark non-vulnerable to the attack (like
compression, and geometric distortion) of an active intruder, or due
to noise in the transmission link.
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.
Abstract: In this paper, in order to categorize ORL database face
pictures, principle Component Analysis (PCA) and Kernel Principal
Component Analysis (KPCA) methods by using Elman neural
network and Support Vector Machine (SVM) categorization methods
are used. Elman network as a recurrent neural network is proposed
for modeling storage systems and also it is used for reviewing the
effect of using PCA numbers on system categorization precision rate
and database pictures categorization time. Categorization stages are
conducted with various components numbers and the obtained results
of both Elman neural network categorization and support vector
machine are compared. In optimum manner 97.41% recognition
accuracy is obtained.
Abstract: The paper deals with the most important changes that have occurred in business because of social media and its impact on organisations and leadership in recent years. It seeks to synthesize existing research, theories and concepts, in order to understand "social destinations", and to provide a bridge from past research to future success. Becoming a "social destination" is a strategic and tactical leadership and management issue and the paper will present the importance of destination leadership in choosing the way towards a social destination and some organisational models. It also presents some social media tools that can be used in transforming a destination into a social one. Adapting organisations to the twentyfirst century means adopting social media as a way of life and a way of business.
Abstract: Most of the academics connect a theory of
multiculturalism with globalization and limit it by last decades of
20th century. However, Kazakh society encountered with this
problem when the Soviet-s rule emerged. As a result of repression,
the Second World War, development of virgin lands representatives
of more than 100 nationalities lives in Kazakhstan. Communist
ideology propagandized internationalism, which would defined
principles of multicultural community but a common ideology
demands a single culture. As a result multicultural society in the
USSR developed under control of Russian culture. Education in the
USSR was conducted in two departments: autochthonous and
Russian. Autochthonous education narrowed student capabilities.
Also because of soviet ideology science was conducted in Russian
Universities provided education in Russian and all science literature
were in Russian. Exceptions were humanitarian fields where Kazakh
departments were admitted. Naturally non-Kazakhs studied in
Russian departments, moreover Kazakhs preferred to study in
Russian as most do nowadays preferring English. As a result Kazakh
society consisted of Kazakhs, Kazakhs who recognized Russian as a
mother tongue and other nationalities who were also Russian
speakers. This aspect continues to distinguish particular qualities of
multicultural community in Kazakhstan.
Abstract: Hazardous Material transportation by road is coupled
with inherent risk of accidents causing loss of lives, grievous injuries,
property losses and environmental damages. The most common type
of hazmat road accident happens to be the releases (78%) of
hazardous substances, followed by fires (28%), explosions (14%) and
vapour/ gas clouds (6 %.).
The paper is discussing initially the probable 'Impact Zones'
likely to be caused by one flammable (LPG) and one toxic (ethylene
oxide) chemicals being transported through a sizable segment of a
State Highway connecting three notified Industrial zones in Surat
district in Western India housing 26 MAH industrial units. Three
'hotspots' were identified along the highway segment depending on
the particular chemical traffic and the population distribution within
500 meters on either sides. The thermal radiation and explosion
overpressure have been calculated for LPG / Ethylene Oxide BLEVE
scenarios along with toxic release scenario for ethylene oxide.
Besides, the dispersion calculations for ethylene oxide toxic release
have been made for each 'hotspot' location and the impact zones
have been mapped for the LOC concentrations. Subsequently, the
maximum Initial Isolation and the protective zones were calculated
based on ERPG-3 and ERPG-2 values of ethylene oxide respectively
which are estimated taking the worst case scenario under worst
weather conditions. The data analysis will be helpful to the local
administration in capacity building with respect to rescue /
evacuation and medical preparedness and quantitative inputs to
augment the District Offsite Emergency Plan document.
Abstract: Warranty is a powerful marketing tool for the
manufacturer and a good protection for both the manufacturer and the
customer. However, warranty always involves additional costs to the
manufacturer, which depend on product reliability characteristics and
warranty parameters. This paper presents an approach to optimisation
of warranty parameters for known product failure distribution to
reduce the warranty costs to the manufacturer while retaining the
promotional function of the warranty. Combination free replacement
and pro-rata warranty policy is chosen as a model and the length of
free replacement period and pro-rata policy period are varied, as well
as the coefficients that define the pro-rata cost function. Multiparametric
warranty optimisation is done by using genetic algorithm.
Obtained results are guideline for the manufacturer to choose the
warranty policy that minimises the costs and maximises the profit.
Abstract: Almost all Libyan industries (both private and public) have struggled with many difficulties during the past three decades due to many problems. These problems have created a strongly negative impact on the productivity and utilization of many companies within Libya. This paper studies the current awareness and implementation levels of Just-In-Time (JIT) within the Libyan Textile private industry. A survey has been applied in this study using an intensive detailed questionnaire. Based on the analysis of the survey responses, the results show that the management body within the surveyed companies has a modest strategy towards most of the areas that are considered as being very crucial in any successful implementation of JIT. The results also show a variation within the implementation levels of the JIT elements as these varies between Low and Acceptable levels. The paper has also identified limitations within the investigated areas within this industry, and has pointed to areas where senior managers within the Libyan textile industry should take immediate actions in order to achieve effective implementation of JIT within their companies.
Abstract: Automatic control of the robotic manipulator involves
study of kinematics and dynamics as a major issue. This paper
involves the forward and inverse kinematics of 2-DOF robotic
manipulator with revolute joints. In this study the Denavit-
Hartenberg (D-H) model is used to model robot links and joints. Also
forward and inverse kinematics solution has been achieved using
Artificial Neural Networks for 2-DOF robotic manipulator. It shows
that by using artificial neural network the solution we get is faster,
acceptable and has zero error.
Abstract: This paper reports a distributed mutual exclusion
algorithm for mobile Ad-hoc networks. The network is clustered
hierarchically. The proposed algorithm considers the clustered
network as a logical tree and develops a token passing scheme
to get the mutual exclusion. The performance analysis and
simulation results show that its message requirement is optimal,
and thus the algorithm is energy efficient.
Abstract: Amount of dissolve oxygen in a river has a great direct affect on aquatic macroinvertebrates and this would influence on the region ecosystem indirectly. In this paper it is tried to predict dissolved oxygen in rivers by employing an easy Fuzzy Logic Modeling, Wang Mendel method. This model just uses previous records to estimate upcoming values. For this purpose daily and hourly records of eight stations in Au Sable watershed in Michigan, United States are employed for 12 years and 50 days period respectively. Calculations indicate that for long period prediction it is better to increase input intervals. But for filling missed data it is advisable to decrease the interval. Increasing partitioning of input and output features influence a little on accuracy but make the model too time consuming. Increment in number of input data also act like number of partitioning. Large amount of train data does not modify accuracy essentially, so, an optimum training length should be selected.
Abstract: We proposed a technique to identify road traffic
congestion levels from velocity of mobile sensors with high accuracy
and consistent with motorists- judgments. The data collection utilized
a GPS device, a webcam, and an opinion survey. Human perceptions
were used to rate the traffic congestion levels into three levels: light,
heavy, and jam. Then the ratings and velocity were fed into a
decision tree learning model (J48). We successfully extracted vehicle
movement patterns to feed into the learning model using a sliding
windows technique. The parameters capturing the vehicle moving
patterns and the windows size were heuristically optimized. The
model achieved accuracy as high as 99.68%. By implementing the
model on the existing traffic report systems, the reports will cover
comprehensive areas. The proposed method can be applied to any
parts of the world.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: The structure of retinal vessels is a prominent feature,
that reveals information on the state of disease that are reflected in
the form of measurable abnormalities in thickness and colour.
Vascular structures of retina, for implementation of clinical diabetic
retinopathy decision making system is presented in this paper.
Retinal Vascular structure is with thin blood vessel, whose accuracy
is highly dependent upon the vessel segmentation. In this paper the
blood vessel thickness is automatically detected using preprocessing
techniques and vessel segmentation algorithm. First the capture
image is binarized to get the blood vessel structure clearly, then it is
skeletonised to get the overall structure of all the terminal and
branching nodes of the blood vessels. By identifying the terminal
node and the branching points automatically, the main and branching
blood vessel thickness is estimated. Results are presented and
compared with those provided by clinical classification on 50 vessels
collected from Bejan Singh Eye hospital..
Abstract: Data Envelopment Analysis (DEA) is a methodology
that computes efficiency values for decision making units (DMU) in a
given period by comparing the outputs with the inputs. In many cases,
there are some time lag between the consumption of inputs and the
production of outputs. For a long-term research project, it is hard to
avoid the production lead time phenomenon. This time lag effect
should be considered in evaluating the performance of organizations.
This paper suggests a model to calculate efficiency values for the
performance evaluation problem with time lag. In the experimental
part, the proposed methods are compared with the CCR and an
existing time lag model using the data set of the 21st century frontier
R&D program which is a long-term national R&D program of Korea.
Abstract: This paper examined the influence of matching
students- learning preferences with the teaching methodology
adopted, on their academic performance in an accounting course in
two types of learning environment in one university in Lebanon:
classes with PowerPoint (PPT) vs. conventional classes. Learning
preferences were either for PPT or for Conventional methodology. A
statistically significant increase in academic achievement is found in
the conventionally instructed group as compared to the group taught
with PPT. This low effectiveness of PPT might be attributed to the
learning preferences of Lebanese students. In the PPT group, better
academic performance was found among students with
learning/teaching match as compared with students with
learning/teaching mismatch. Since the majority of students display a
preference for the conventional methodology, the result might
suggest that Lebanese students- performance is not optimized by PPT
in the accounting classrooms, not because of PPT itself, but because
it is not matching the Lebanese students- learning preferences in such
a quantitative course.