Abstract: This paper describes a method of signal process applied
on an end effects of Hilbert-Huang transform (HHT) to provide an
improvement in the reality of spectrum. The method is based on
back-propagation network (BPN). To improve the effect, the end
extension of the original signal is obtained by back-propagation
network. A full waveform including origin and its extension is
decomposed by using empirical mode decomposition (EMD) to obtain
intrinsic mode functions (IMFs) of the waveform. Then, the Hilbert
transform (HT) is applied to the IMFs to obtain the Hilbert spectrum of
the waveform. As a result, the method is superiority of the processing
of end effect of HHT to obtain the real frequency spectrum of signals.
Abstract: To assess the effects of functional protein on osteoblast, Large quantity of high-purity osteoblasts had been cultivated successfully by adopting sequential enzyme digestion. The growth curve of osteoblasts was protracted by cell counting. Proliferation of osteoblasts was assessed by MTT colorimetry. The experimental results show the functional protein can enhance proliferation, the properties of adhesion and discuss the effect of osteopontin on osteoblast.
Abstract: Among many different methods that are used for
optimizing different engineering problems mathematical (numerical)
optimization techniques are very important because they can easily
be used and are consistent with most of engineering problems. Many
studies and researches are done on stability analysis of three
dimensional (3D) slopes and the relating probable slip surfaces and
determination of factors of safety, but in most of them force
equilibrium equations, as in simplified 2D methods, are considered
only in two directions. In other words for decreasing mathematical
calculations and also for simplifying purposes the force equilibrium
equation in 3rd direction is omitted. This point is considered in just a
few numbers of previous studies and most of them have only given a
factor of safety and they haven-t made enough effort to find the most
probable slip surface. In this study shapes of the slip surfaces are
modeled, and safety factors are calculated considering the force
equilibrium equations in all three directions, and also the moment
equilibrium equation is satisfied in the slip direction, and using
nonlinear programming techniques the shape of the most probable
slip surface is determined. The model which is used in this study is a
3D model that is composed of three upper surfaces which can cover
all defined and probable slip surfaces. In this research the meshing
process is done in a way that all elements are prismatic with
quadrilateral cross sections, and the safety factor is defined on this
quadrilateral surface in the base of the element which is a part of the
whole slip surface. The method that is used in this study to find the
most probable slip surface is the non-linear programming method in
which the objective function that must get optimized is the factor of
safety that is a function of the soil properties and the coordinates of
the nodes on the probable slip surface. The main reason for using
non-linear programming method in this research is its quick
convergence to the desired responses. The final results show a good
compatibility with the previously used classical and 2D methods and
also show a reasonable convergence speed.
Abstract: Energy consumption is a very important topic these
days especially regarding air conditioning in residential buildings,
since this takes the biggest amount of energy in buildings total
consumption, residential buildings constitute the biggest percentage
of energy consumption in Bahrain.
This research reflects on the effects of shading percentage in
different solar orientations on the energy consumption inside
residential buildings (domestic dwellings).
The research as found that, there are different effects of shading in
changing building orientation:
• 0.69% for the shading percentage 25% when the building is
oriented to the north (0º);
• 18.59% for 75% of shading in north-west orientation
(325º);
• The best effect for shading is in north-west orientation
(315º);
• The less effect for shading was in case of the building
orientation is the north (0º).
Abstract: Plant growth is affected by the osmotic stress as well as toxicity of salt in leaves. In order to study of salt stress effects on stomatal conductance and growth rate and relationship between them as wells osmotic and Na+-specific effects on these traits, four bread wheat genotypes differing in salt tolerance were selected. Salinity was applied when the leaf 4 was fully expanded. Sodium (Na+) concentrations in flag leaf blade at 3 salinity levels (0, 100 and 200 mM NaCl) were measured. Salt-tolerant genotypes showed higher stomatal conductance and growth rate compared to salt-sensitive ones. After 10 and 20 days exposure to salt, stomatal conductance and relative growth rate were reduced, but the reduction was greater in sensitive genotypes. Growth rate was reduced severely in the first period (1-10 days) of salt commencements and it was due to osmotic effect of salt not Na+ toxicity. In the second period (11-20 days) after salt treatment growth reduced only when salt accumulated to toxic concentrations in the leaves. A positive relationship between stomatal conductance and relative growth rate showed that stomatal conductance can be a reliable indicator of growth rate, and finally can be considered as a sensitive indicator of the osmotic stress. It seems 20 days after salinity, the major effect of salt, especially at low to moderate salinity levels on growth properties was due to the osmotic effect of salt, not to Na+-specific effects within the plant.
Abstract: This paper studied the synthesis of monoacylglycerol (monolaurin) by glycerolysis of coconut oil and crude glycerol, catalyzed by Carica papaya lipase. Coconut oil obtained from cold pressed extraction method and crude glycerol obtained from the biodiesel plant in Department of Chemistry, Uttaradit Rajabhat University, Thailand which used oils were used as raw materials for biodiesel production through transesterification process catalyzed by sodium hydroxide. The influences of the following variables were studied: (i) type of organic solvent, (ii) molar ratio of substrate, (iii) reaction temperature, (iv) reaction time, (v) lipase dosage, and (vi) initial water activity of enzyme. High yields in monoacylglycerol (58.35%) were obtained with molar ratio of glycerol to oil at 8:1 in ethanol, temperature was controlled at 45oC for 36 hours, the amount of enzyme used was 20 wt% of oil and initial water activity of enzyme at 0.53.
Abstract: A mammal-s body can be seen as a blood vessel with
complex tunnels. When heart pumps blood periodically, blood runs
through blood vessels and rebounds from walls of blood vessels.
Blood pressure signals can be measured with complex but periodic
patterns. When an artery is clamped during a surgical operation, the
spectrum of blood pressure signals will be different from that of
normal situation. In this investigation, intestinal artery clamping
operations were conducted to a pig for simulating the situation of
intestinal blocking during a surgical operation. Similarity theory is a
convenient and easy tool to prove that patterns of blood pressure
signals of intestinal artery blocking and unblocking are surely
different. And, the algorithm of Hilbert Huang Transform can be
applied to extract the character parameters of blood pressure pattern.
In conclusion, the patterns of blood pressure signals of two different
situations, intestinal artery blocking and unblocking, can be
distinguished by these character parameters defined in this paper.
Abstract: Formulation of biological profile is one of the modern roles of forensic anthropologist. The present study was conducted to estimate height using foot and shoeprint length of Malaysian population. The present work can be very useful information in the process of identification of individual in forensic cases based on shoeprint evidence. It can help to narrow down suspects and ease the police investigation. Besides, stature is important parameters in determining the partial identify of unidentified and mutilated bodies. Thus, this study can help the problem encountered in cases of mass disaster, massacre, explosions and assault cases. This is because it is very hard to identify parts of bodies in these cases where people are dismembered and become unrecognizable. Samples in this research were collected from 200 Malaysian adults (100 males and 100 females) with age ranging from 20 to 45 years old. In this research, shoeprint length were measured based on the print of the shoes made from the flat shoes. Other information like gender, foot length and height of subject were also recorded. The data was analyzed using IBM® SPSS Statistics 19 software. Results indicated that, foot length has a strong correlation with stature than shoeprint length for both sides of the feet. However, in the unknown, where the gender was undetermined have shown a better correlation in foot length and shoeprint length parameter compared to males and females analyzed separately. In addition, prediction equations are developed to estimate the stature using linear regression analysis of foot length and shoeprint length. However, foot lengths give better prediction than shoeprint length.
Abstract: Aircraft propulsion systems often use Y-shaped
subsonic diffusing ducts as twin air-intakes to supply the ambient air
into the engine compressor for thrust generation. Due to space
constraint, the diffusers need to be curved, which causes severe flow
non-uniformity at the engine face. The present study attempt to
control flow in a mild-curved Y-duct diffuser using trapezoidalshaped
vortex generators (VG) attached on either both the sidewalls
or top and bottom walls of the diffuser at the inflexion plane. A
commercial computational fluid dynamics (CFD) code is modified
and is used to simulate the effects of SVG in flow of a Y-duct
diffuser. A few experiments are conducted for CFD code validation,
while the rest are done computationally. The best combination of Yduct
diffuser is found with VG-2 arranged in co-rotating sequence
and attached to both the sidewalls, which ensures highest static
pressure recovery, lowest total pressure loss, minimum flow
distortion and less flow separation in Y-duct diffuser. The decrease in
VG height while attached to top and bottom walls further improves
axial flow uniformity at the diffuser outlet by a great margin as
compared to the bare duct.
Abstract: This paper suggests a calibration method to reduce
errors occurring due to mobile robot sliding during location estimation
using the Dead-reckoning. Due to sliding of the mobile robot caused
between its wheels and the road surface while on free run, location
estimation can be erroneous. Sliding especially occurs during
cornering of mobile robot. Therefore, in order to reduce these frequent
sliding errors in cornering, we calibrated the mobile robot-s heading
values using a vision camera and templates of the ceiling.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: In this research, natural canthaxanthin as one of the
most important carotenoids was extracted from Dietzia
natronolimnaea HS-1. The changes of canthaxanthin enriched in oilin-
water emulsions with vegetable oil (5 mg/ 100 mL), Arabic gum (5
mg/100 mL), and potassium sorbate (0.5 g/100 mL) was investigated.
The effects of different pH (3, 5 and 7), as well as, time treatment (3,
18 and 33 days) in the environmental temperature (24°C) on the
degradation were studied by response surface methodology (RSM).
The Hunter values (L*, a*, and b*) and the concentration of
canthaxanthin (C, mg/L) illustrated more degradation of this pigment
at low pHs (pH≤ 4) by passing the time (days≥10) with R² 97.00%,
91.31%, 97.60%, and 99.54% for C, L*, a*, and b* respectively. The
predicted model were found to be significant (p
Abstract: Signalized intersections on high-volume arterials are
often congested during peak hours, causing a decrease in through
movement efficiency on the arterial. Much of the vehicle delay
incurred at conventional intersections is caused by high left-turn
demand. Unconventional intersection designs attempt to reduce
intersection delay and travel time by rerouting left-turns away from
the main intersection and replacing it with right-turn followed by Uturn.
The proposed new type of U-turn intersection is geometrically
designed with a raised island which provides a protected U-turn
movement. In this study several scenarios based on different
distances between U-turn and main intersection, traffic volume of
major/minor approaches and percentage of left-turn volumes were
simulated by use of AIMSUN, a type of traffic microsimulation
software. Subsequently some models are proposed in order to
compute travel time of each movement. Eventually by correlating
these equations to some in-field collected data of some implemented
U-turn facilities, the reliability of the proposed models are approved.
With these models it would be possible to calculate travel time of
each movement under any kind of geometric and traffic condition. By
comparing travel time of a conventional signalized intersection with
U-turn intersection travel time, it would be possible to decide on
converting signalized intersections into this new kind of U-turn
facility or not. However comparison of travel time is not part of the
scope of this research. In this paper only travel time of this innovative
U-turn facility would be predicted. According to some before and
after study about the traffic performance of some executed U-turn
facilities, it is found that commonly, this new type of U-turn facility
produces lower travel time. Thus, evaluation of using this type of
unconventional intersection should be seriously considered.
Abstract: Crypto System Identification is one of the challenging tasks in Crypt analysis. The paper discusses the possibility of employing Neural Networks for identification of Cipher Systems from cipher texts. Cascade Correlation Neural Network and Back Propagation Network have been employed for identification of Cipher Systems. Very large collection of cipher texts were generated using a Block Cipher (Enhanced RC6) and a Stream Cipher (SEAL). Promising results were obtained in terms of accuracy using both the Neural Network models but it was observed that the Cascade Correlation Neural Network Model performed better compared to Back Propagation Network.
Abstract: The paper investigates the relationship between the foreign direct investment (FDI) and the corporate governance or transparency by investigating the country-level FDI flows, FDI inward performance, corporate governance and transparency variables. From the regression analysis with Newey-West estimator of 28 country panel data from 1990- 2002, we find strong positive relationships between corporate governance or transparency level of hosting countries and FDI inward performance within hosting countries. A strong positive relationship is found between anti-director rights level or number of analysts of hosting countries and FDI inward performance within hosting countries. Also, we find a positive relationship between the number of analysts of hosting countries and FDI inflows. The empirical results are consistent with stock market liberalizations and corporate governance explanations of reasons for FDI.
Abstract: In this manuscript, the LBM is applied for simulating of Mixed Convection in a Lid-Driven cavity with an open side. The cavity horizontal walls are insulated while the west Lid-driven wall is maintained at a uniform temperature higher than the ambient. Prandtl number (Pr) is fixed to 0.71 (air) while Reynolds number (Re) , Richardson number (Ri) and aspect ratio (A) of the cavity are changed in the range of 50-150 , of 0.1-10 and of 1-4 , respectively. The numerical code is validated for the standard square cavity, and then the results of an open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number (Nu) on lid- driven wall decreases and with same Reynolds number (Re) by increasing of aspect ratio (A), Richardson number plays more important role in heat transfer rate.
Abstract: In this paper, algorithms for the automatic localisation
of two anatomical soft tissue landmarks of the head the medial
canthus (inner corner of the eye) and the tragus (a small, pointed,
cartilaginous flap of the ear), in CT images are describet. These
landmarks are to be used as a basis for an automated image-to-patient
registration system we are developing. The landmarks are localised
on a surface model extracted from CT images, based on surface
curvature and a rule based system that incorporates prior knowledge
of the landmark characteristics. The approach was tested on a dataset
of near isotropic CT images of 95 patients. The position of the
automatically localised landmarks was compared to the position of
the manually localised landmarks. The average difference was 1.5
mm and 0.8 mm for the medial canthus and tragus, with a maximum
difference of 4.5 mm and 2.6 mm respectively.The medial canthus
and tragus can be automatically localised in CT images, with
performance comparable to manual localisation
Abstract: The prediction of transmembrane helical segments
(TMHs) in membrane proteins is an important field in the
bioinformatics research. In this paper, a new method based on discrete
wavelet transform (DWT) has been developed to predict the number
and location of TMHs in membrane proteins. PDB coded as 1KQG
was chosen as an example to describe the prediction of the number and
location of TMHs in membrane proteins by using this method. To
access the effect of the method, 80 proteins with known 3D-structure
from Mptopo database are chosen at random as the test objects
(including 325 TMHs), 308 of which can be predicted accurately, the
average predicted accuracy is 96.3%. In addition, the above 80
membrane proteins are divided into 13 groups according to their
function and type. In particular, the results of the prediction of TMHs
of the 13 groups are satisfying.
Abstract: China apparel industry, which is deeply embedded in
the global production network (GPN), faces the dual pressures of
social upgrading and economic upgrading. Based on the survey in
Ningbo apparel cluster, the paper shows the state of corporate social
responsibility (CSR) in China apparel industry is better than before.
And the investigation indicates that the firms who practice CSR
actively perform better both socially and economically than those who
inactively. The research demonstrates that CSR can be an initial
capital rather than cost, and “doing well by doing good" is also existed
in labor intensive industry.
Abstract: The paper deals with a mathematical model for fluid dynamic flows on road networks which is based on conservation laws. This nonlinear framework is based on the conservation of cars. We focus on traffic circle, which is a finite number of roads that meet at some junctions. The traffic circle with junctions having either one incoming and two outgoing or two incoming and one outgoing roads. We describe the numerical schemes with the particular boundary conditions used to produce approximated solutions of the problem.