Abstract: This paper describes the design and fabrication of a clock and data recovery circuit (CDR). We propose a new clock and data recovery which is based on a 1/4-rate frequency detector (QRFD). The proposed frequency detector helps reduce the VCO frequency and is thus advantageous for high speed application. The proposed frequency detector can achieve low jitter operation and extend the pull-in range without using the reference clock. The proposed CDR was implemented using a 1/4-rate bang-bang type phase detector (PD) and a ring voltage controlled oscillator (VCO). The CDR circuit has been fabricated in a standard 0.18 CMOS technology. It occupies an active area of 1 x 1 and consumes 90 mW from a single 1.8V supply.
Abstract: Multi-loop (De-centralized) Proportional-Integral-
Derivative (PID) controllers have been used extensively in process
industries due to their simple structure for control of multivariable
processes. The objective of this work is to design multiple-model
adaptive multi-loop PID strategy (Multiple Model Adaptive-PID)
and neural network based multi-loop PID strategy (Neural Net
Adaptive-PID) for the control of multivariable system. The first
method combines the output of multiple linear PID controllers,
each describing process dynamics at a specific level of operation.
The global output is an interpolation of the individual multi-loop
PID controller outputs weighted based on the current value of the
measured process variable. In the second method, neural network
is used to calculate the PID controller parameters based on the
scheduling variable that corresponds to major shift in the process
dynamics. The proposed control schemes are simple in structure with
less computational complexity. The effectiveness of the proposed
control schemes have been demonstrated on the CSTR process,
which exhibits dynamic non-linearity.
Abstract: THEOS is the first earth observation spacecraft of Thailand which was launched on the 1st October 2008 and is currently operated by GISTDA. The transfer phase has been performed by Astrium Flight Dynamics team leading to a hand over to GISTDA teams starting mid-October 2008. The THEOS spacecraft-s orbit is LEO and has the same repetitivity (14+5/26) as the SPOT spacecraft, i.e. the same altitude of 822 km but it has a different mean local solar time (LST). Ground track maintenance manoeuvres are performed to maintain the ground track within a predefined control band around the reference ground track and the band is ±40 km for THEOS spacecraft. This paper presents the first ground track maintenance manoeuvre of THEOS spacecraft and the detailed results. In addition, it also includes one and a half year of operation as seen by GISTDA operators. It finally describes the foreseenable activities for the next orbit control manoeuvre (OCM) preparation.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: As emails communications have no consistent
authentication procedure to ensure the authenticity, we present an
investigation analysis approach for detecting forged emails based on
Random Forests and Naïve Bays classifiers. Instead of investigating
the email headers, we use the body content to extract a unique writing
style for all the possible suspects. Our approach consists of four main
steps: (1) The cybercrime investigator extract different effective
features including structural, lexical, linguistic, and syntactic
evidence from previous emails for all the possible suspects, (2) The
extracted features vectors are normalized to increase the accuracy
rate. (3) The normalized features are then used to train the learning
engine, (4) upon receiving the anonymous email (M); we apply the
feature extraction process to produce a feature vector. Finally, using
the machine learning classifiers the email is assigned to one of the
suspects- whose writing style closely matches M. Experimental
results on real data sets show the improved performance of the
proposed method and the ability of identifying the authors with a
very limited number of features.
Abstract: The Bayesian Optimization Algorithm (BOA) is an algorithm based on the estimation of distributions. It uses techniques from modeling data by Bayesian networks to estimating the joint distribution of promising solutions. To obtain the structure of Bayesian network, different search algorithms can be used. The key point that BOA addresses is whether the constructed Bayesian network could generate new and useful solutions (strings), which could lead the algorithm in the right direction to solve the problem. Undoubtedly, this ability is a crucial factor of the efficiency of BOA. Varied search algorithms can be used in BOA, but their performances are different. For choosing better ones, certain suitable method to present their ability difference is needed. In this paper, a greedy search algorithm and a stochastic search algorithm are used in BOA to solve certain optimization problem. A method using Kullback-Leibler (KL) Divergence to reflect their difference is described.
Abstract: This paper presents the visual control flow support of Visual Modeling and Transformation System (VMTS), which facilitates composing complex model transformations out of simple transformation steps and executing them. The VMTS Visual Control Flow Language (VCFL) uses stereotyped activity diagrams to specify control flow structures and OCL constraints to choose between different control flow branches. This work discusses the termination properties of VCFL and provides an algorithm to support the termination analysis of VCFL transformations.
Abstract: Drought is a phenomenon caused by
environmental and climatic changes. This phenomenon is
affected by shortage of rainfall and temperature. Dust is one
of important environmental problems caused by climate
change and drought. With recent multi-year drought, many
environmental crises caused by dust in Iran and Middle East.
Dust in the vast areas of the provinces occurs with high
frequency. By dust affecting many problems created in terms
of health, social and economic. In this study, we tried to study
the most important factors causing dust. In this way we have
used the satellite images and meteorological data. Finally,
strategies to deal with the dust will be mentioned.
Abstract: Malware is software which was invented and meant for doing harms on computers. Malware is becoming a significant threat in computer network nowadays. Malware attack is not just only involving financial lost but it can also cause fatal errors which may cost lives in some cases. As new Internet Protocol version 6 (IPv6) emerged, many people believe this protocol could solve most malware propagation issues due to its broader addressing scheme. As IPv6 is still new compares to native IPv4, some transition mechanisms have been introduced to promote smoother migration. Unfortunately, these transition mechanisms allow some malwares to propagate its attack from IPv4 to IPv6 network environment. In this paper, a proof of concept shall be presented in order to show that some existing IPv4 malware detection technique need to be improvised in order to detect malware attack in dual-stack network more efficiently. A testbed of dual-stack network environment has been deployed and some genuine malware have been released to observe their behaviors. The results between these different scenarios will be analyzed and discussed further in term of their behaviors and propagation methods. The results show that malware behave differently on IPv6 from the IPv4 network protocol on the dual-stack network environment. A new detection technique is called for in order to cater this problem in the near future.
Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: This paper discusses the classification process for medical data. In this paper, we use the data from ACM KDDCup 2008 to demonstrate our classification process based on latent topic discovery. In this data set, the target set and outliers are quite different in their nature: target set is only 0.6% size in total, while the outliers consist of 99.4% of the data set. We use this data set as an example to show how we dealt with this extremely biased data set with latent topic discovery and noise reduction techniques. Our experiment faces two major challenge: (1) extremely distributed outliers, and (2) positive samples are far smaller than negative ones. We try to propose a suitable process flow to deal with these issues and get a best AUC result of 0.98.
Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: The mountain road slope failures triggered by
earthquake activities and torrential rain namely to create the disaster.
Province Road No. 24 is a main route to the Wutai Township. The area
of the study is located at the mileages between 46K and 47K along the
road. However, the road has been suffered frequent damages as a result
of landslide and slope failures during typhoon seasons. An
understanding of the sliding behaviors in the area appears to be
necessary. Slope failures triggered by earthquake activities and heavy
rainfalls occur frequently. The study is to understand the mechanism
of slope failures and to look for the way to deal with the situation. In
order to achieve these objectives, this paper is based on theoretical and
structural geology data interpretation program to assess the potential
slope sliding behavior. The study showed an intimate relationship
between the landslide behavior of the slopes and the stratum materials,
based on structural geology analysis method to analysis slope stability
and finds the slope safety coefficient to predict the sites of destroyed
layer. According to the case study and parameter analyses results, the
slope mainly slips direction compared to the site located in the
southeast area. Find rainfall to result in the rise of groundwater level is
main reason of the landslide mechanism. Future need to set up
effective horizontal drain at corrective location, that can effective
restrain mountain road slope failures and increase stability of slope.
Abstract: This paper shows that the economy of any country
can be presented as three different shells such as: economic shell of a
big, a medium and a small business. The new concepts were
introduced such as: volume of an economic shell, coefficient of
shell-s expansion (compression) etc. These shells can expansion or
compress under action by internal or external powers and when shell
expansions - it means the rising of a business activity and
compression shows us that economy goes on recession. This process
of an expansion or a compression can develop in the various ways
like linear, logarithm or any other mathematical laws.
Abstract: In this paper we will develop further the sequential
life test approach presented in a previous article by [1] using an
underlying two parameter Weibull sampling distribution. The
minimum life will be considered equal to zero. We will again provide
rules for making one of the three possible decisions as each
observation becomes available; that is: accept the null hypothesis H0;
reject the null hypothesis H0; or obtain additional information by
making another observation. The product being analyzed is a new
type of a low alloy-high strength steel product. To estimate the shape
and the scale parameters of the underlying Weibull model we will use
a maximum likelihood approach for censored failure data. A new
example will further develop the proposed sequential life testing
approach.
Abstract: Most of the concurrent transactional protocols consider
serializability as a correctness criterion of the transactions execution.
Usually, the proof of the serializability relies on mathematical proofs
for a fixed finite number of transactions. In this paper, we introduce
a protocol to deal with an infinite number of transactions which are
iterated infinitely often. We specify serializability of the transactions
and the protocol using a specification language based on temporal
logics. It is worthwhile using temporal logics such as LTL (Lineartime
Temporal Logic) to specify transactions, to gain full automatic
verification by using model checkers.
Abstract: In this paper, mathematical modeling of detonation in the ground is studied. Estimation of flow parameters such as velocity, maximum velocity, acceleration, maximum acceleration, shock pressure as a result of an explosion in the ground have been computed in an appropriate dynamic model approach. The variation of these parameters with the diameter of detonation place (L), density of earth or stone (¤ü), time decay of detonation (T), peak pressure (Pm), and time (t) have been analyzed. The model has been developed from the concept of underwater explosions [Refs. [1]-[3]] with appropriate changes to the present model requirements.
Abstract: This paper present a new method for design of power
system stabilizer (PSS) based on sliding mode control (SMC)
technique. The control objective is to enhance stability and improve
the dynamic response of the multi-machine power system. In order to
test effectiveness of the proposed scheme, simulation will be carried
out to analyze the small signal stability characteristics of the system
about the steady state operating condition following the change in
reference mechanical torque and also parameters uncertainties. For
comparison, simulation of a conventional control PSS (lead-lag
compensation type) will be carried out. The main approach is
focusing on the control performance which later proven to have the
degree of shorter reaching time and lower spike.