Abstract: In this paper, relationship between different properties
of IC concrete and water cement ratio, obtained from a
comprehensive experiment conducted on IC using local materials
(Burnt clay chips- BC) is presented. In addition, saturated SAP was
used as an IC material in some cases. Relationships have been
developed through regression analysis. The focus of this analysis is
on developing relationship between a dependent variable and an
independent variable. Different percent replacements of BC and
water cement ratios were used. Compressive strength, modulus of
elasticity, water permeability and chloride permeability were tested
and variations of these parameters were analyzed with respect to
water cement ratio.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: Traditional mechanical control systems in thrust
vectoring are efficient in rocket thrust guidance but their costs
and their weights are excessive. The fluidic injection in the nozzle
divergent constitutes an alternative procedure to achieve the goal. In
this paper, we present a 3D analytical model for fluidic injection
in a supersonic nozzle integrating an orifice. The fluidic vectoring
uses a sonic secondary injection in the divergent. As a result, the
flow and interaction between the main and secondary jet has built in
order to express the pressure fields from which the forces and thrust
vectoring are deduced. Under various separation criteria, the present
analytical model results are compared with the existing numerical
and experimental data from the literature.
Abstract: In recent years, the use of the aluminum based alloys
in the industry and technology are increasing. Alloying elements in
aluminum have further been improving the strength and stiffness
properties that provide superior compared to other metals. In this
study, investigation of physical properties (microstructure,
microhardness, tensile strength, electrical conductivity and thermal
properties) in the Al-12.6wt.%Si-%2wt.Ni ternary alloy were
investigated. Al-Si-Ni alloy was prepared in vacuum atmosphere. The
samples were directionally solidified upwards with different growth
rate V (8.3−165.45 μm/s) at constant temperature gradient G (7.73
K/mm). The flake spacings (λ), microhardness (HV), ultimate tensile
strength (σ), electrical resistivity (ρ) and thermal properties (H, Cp,
Tm) of the samples were measured. Influence of the growth rate and
spacings on microhardness, ultimate tensile strength and electrical
resistivity were investigated and relationships between them were
obtained. According to results, λ values decrease with increasing V,
but HV, σ and ρ values increase with increasing V. Variations of
electrical resistivity (ρ) of solidified samples were also measured.
The enthalpy of fusion (H) and specific heat (Cp) for the alloy was
also determined by differential scanning calorimeter (DSC) from
heating trace during the transformation from liquid to solid. The
results in this work were compared with the previous similar
experimental results.
Abstract: In this article, a method is presented to effectively
estimate the deformed shape of a thick plate due to line heating. The
method uses a fifth order spline interpolation, with up to C3
continuity at specific points to compute the shape of the deformed
geometry. First and second order derivatives over a surface are the
resulting parameters of a given heating line on a plate. These
parameters are determined through experiments and/or finite element
simulations. Very accurate kriging models are fitted to real or virtual
surfaces to build-up a database of maps. Maps of first and second
order derivatives are then applied on numerical plate models to
evaluate their evolving shapes through a sequence of heating lines.
Adding an optimization process to this approach would allow
determining the trajectories of heating lines needed to shape complex
geometries, such as Francis turbine blades.
Abstract: The LSTF experiment simulating the SGTR accident at
the Mihama Unit-2 reactor is analyzed using the RELAP5/MOD3.3
code. In the accident, and thus in the experiment, the ECC water was
injected not only into the cold legs but into the upper plenum. Overall
transients during the experiment such as pressures and fluid
temperatures are simulated well by the code. The cold-leg fluid
temperatures are shown to decrease if the upper plenum injection
system is connected to the cold leg. It is found that the cold-leg fluid
temperatures also decrease if the upper-plenum injection is not used
and the cold-leg injection alone is actuated.
Abstract: In this work, the plastic behaviour of cold-rolled zinc
coated dual-phase steel sheets DP600 and DP800 grades is firstly
investigated with the help of uniaxial, hydraulic bulge and Forming
Limit Curve (FLC) tests. The uniaxial tensile tests were performed in
three angular orientations with respect to the rolling direction to
evaluate the strain-hardening and plastic anisotropy. True stressstrain
curves at large strains were determined from hydraulic bulge
testing and fitted to a work-hardening equation. The limit strains are
defined at both localized necking and fracture conditions according to
Nakajima’s hemispherical punch procedure. Also, an elasto-plastic
localization model is proposed in order to predict strain and stress
based forming limit curves. The investigated dual-phase sheets
showed a good formability in the biaxial stretching and drawing FLC
regions. For both DP600 and DP800 sheets, the corresponding
numerical predictions overestimated and underestimated the
experimental limit strains in the biaxial stretching and drawing FLC
regions, respectively. This can be attributed to the restricted failure
necking condition adopted in the numerical model, which is not
suitable to describe the tensile and shear fracture mechanisms in
advanced high strength steels under equibiaxial and biaxial stretching
conditions.
Abstract: Below-knee amputees commonly experience
asymmetrical gait patterns. It is generally believed that ischemia is
related to the formation of pressure sores due to uneven distribution
of forces. Micro-vascular responses can reveal local malnutrition.
Changes in local skin blood supply under various external loading
conditions have been studied for a number of years. Radionuclide
clearance, photo-plethysmography, trans-cutaneous oxygen tension
along with other studies showed that the blood supply would be
influenced by the epidermal forces, and the rate and the amount of
blood supply would decrease with increased epidermal loads being
shear forces or normal forces. Several cases of socket designs were
investigated using Finite Element Model (FEM) and Design of
Experiment (DOE) to increase flexibility and minimize the pressure
at the limb/socket interface using ultra high molecular weight
polyethylene (UHMWPE) and polyamide 6 (PA6) or Duraform. The
pressure reliefs at designated areas where reducing thickness is
involved are seen to be critical in determination of amputees’ comfort
and are very important to clinical applications. Implementing a hole
between the Patellar Tendon (PT) and Distal Tibia (DT) would
decrease stiffness and increase prosthesis range of motion where
flexibility is needed. In addition, displacement and prosthetic energy
storage increased without compromising mechanical efficiency and
prosthetic design integrity.
Abstract: As smartphones are equipped with various sensors,
there have been many studies focused on using these sensors to create
valuable applications. Human activity recognition is one such
application motivated by various welfare applications, such as the
support for the elderly, measurement of calorie consumption, lifestyle
and exercise patterns analyses, and so on. One of the challenges one
faces when using smartphone sensors for activity recognition is that
the number of sensors should be minimized to save battery power. In
this paper, we show that a fairly accurate classifier can be built that
can distinguish ten different activities by using only a single sensor
data, i.e., the smartphone accelerometer data. The approach that we
adopt to deal with this twelve-class problem uses various methods.
The features used for classifying these activities include not only the
magnitude of acceleration vector at each time point, but also the
maximum, the minimum, and the standard deviation of vector
magnitude within a time window. The experiments compared the
performance of four kinds of basic multi-class classifiers and the
performance of four kinds of ensemble learning methods based on
three kinds of basic multi-class classifiers. The results show that
while the method with the highest accuracy is ECOC based on
Random forest.
Abstract: The global demand for long-tailed macaques for
medical experimentation has continued to increase. Fulfillment of
Indonesian export demands has been mostly from natural habitats,
based on a harvesting quota. This quota has been determined
according to the total catch for a given year, and not based on
consideration of any demographic parameters or physical
environmental factors with regard to the animal; hence threatening
the sustainability of the various populations. It is therefore necessary
to formulate a method for calculating a sustainable harvesting quota,
based on population parameters in natural habitats. Considering the
possibility of variations in habitat characteristics and population
parameters, a time series observation of demographic and
physical/biotic parameters, in various habitats, was performed on 13
groups of long-tailed macaques, distributed throughout the West
Java, Lampung and Yogyakarta areas of Indonesia. These provinces
were selected for comparison of the influence of human/tourism
activities. Data on population parameters that was collected included
data on life expectancy according to age class, numbers of
individuals by sex and age class, and ‘ratio of infants to reproductive
females’. The estimation of population growth was based on a
population dynamic growth model: the Leslie matrix. The harvesting
quota was calculated as being the difference between the actual
population size and the MVP (minimum viable population) for each
sex and age class. Observation indicated that there were variations within group size
(24–106 individuals), gender (sex) ratio (1:1 to 1:1.3), life expectancy
value (0.30 to 0.93), and ‘ratio of infants to reproductive females’
(0.23 to 1.56). Results of subsequent calculations showed that
sustainable harvesting quotas for each studied group of long-tailed
macaques, ranged from 29 to 110 individuals. An estimation model
of the MVP for each age class was formulated as Log Y = 0.315 +
0.884 Log Ni (number of individual on ith age class). This study also
found that life expectancy for the juvenile age class was affected by
the humidity under tree stands, and dietary plants’ density at sapling,
pole and tree stages (equation: Y=2.296 – 1.535 RH + 0.002 Kpcg –
0.002 Ktg – 0.001 Kphn, R2 = 89.6% with a significance value of
0.001). By contrast, for the sub-adult-adult age class, life expectancy
was significantly affected by slope (equation: Y=0.377 = 0.012 Kml,
R2 = 50.4%, with significance level of 0.007). The infant-toreproductive-
female ratio was affected by humidity under tree stands,
and dietary plant density at sapling and pole stages (equation: Y = -
1.432 + 2.172 RH – 0.004 Kpcg + 0.003 Ktg, R2 = 82.0% with
significance level of 0.001). This research confirmed the importance
of population parameters in determining the minimum viable
population, and that MVP varied according to habitat characteristics
(especially food availability). It would be difficult therefore, to
formulate a general mathematical equation model for determining a
harvesting quota for the species as a whole.
Abstract: One of the most critical decision points in the design of a
face recognition system is the choice of an appropriate face representation.
Effective feature descriptors are expected to convey sufficient, invariant
and non-redundant facial information. In this work we propose a set of
Hahn moments as a new approach for feature description. Hahn moments
have been widely used in image analysis due to their invariance, nonredundancy
and the ability to extract features either globally and locally.
To assess the applicability of Hahn moments to Face Recognition we
conduct two experiments on the Olivetti Research Laboratory (ORL)
database and University of Notre-Dame (UND) X1 biometric collection.
Fusion of the global features along with the features from local facial
regions are used as an input for the conventional k-NN classifier. The
method reaches an accuracy of 93% of correctly recognized subjects for
the ORL database and 94% for the UND database.
Abstract: Steel slag is a by-product of the steel industry and can
be used potentially as aggregate in the asphalt mixture. This study
evaluates the use of Steel Slag Aggregates (SSA) as a substitute for
natural aggregates in the production of hot mix asphalt (HMA) for
road construction. Based on intensive laboratory testing program, the
characteristic properties of SSA were assessed to determine its
suitability to be used in HMA. Four different percentages (0, 50, 75,
and 100%) of SSA were used, and the proposed mix designs for
HMA were conducted in accordance with Marshall mix design. The
experiment results revealed that the addition of SSA has a significant
improvement on the properties of HMA. An increase in density and
stability and a reduction in flow and air voids values were clearly
observed in specimens prepared with 100% SSA. It is concluded that
the steel slag can be considered reasonable alternative source of
aggregate for concrete asphalt mixture production.
Abstract: A solar dish collector has been designed, fabricated
and tested for its performance on 10-03-2015 in Salem, Tamilnadu,
India. The experiments on cooking vessels of coated and un-coated
with 5 Liters capacity have been used for cooking Rice. The results
are shown in graphs. The solar cooker is always capable of cooking
food within the expected length of time and based on the solar
radiation levels. With minimum cooking power, the coated pressure
cooker of 5 Liters capacity cooks the food at faster manner. This is
due to the conductivity of the coating material provided in the cooker.
Abstract: In this paper, we report the development of the device
for diagnostics of cardiovascular system state and associated
automated workstation for large-scale medical measurement data
collection and analysis. It was shown that optimal design for the
monitoring device is wristband as it represents engineering trade-off
between accuracy and usability. Monitoring device is based on the
infrared reflective photoplethysmographic sensor, which allows
collecting multiple physiological parameters, such as heart rate and
pulsing wave characteristics. Developed device uses BLE interface
for medical and supplementary data transmission to the coupled
mobile phone, which processes it and send it to the doctor's
automated workstation. Results of this experimental model
approbation confirmed the applicability of the proposed approach.
Abstract: In order to obtain efficient pollutants removal in
small-scale wastewater treatment plants, uniform water flow has to be
achieved. The experimental setup, designed for treating high-load
wastewater (leachate), consists of two aerobic biological reactors and
a lamellar settler. Both biological tanks were aerated by using three
different types of aeration systems - perforated pipes, membrane air
diffusers and tube ceramic diffusers. The possibility of homogenizing
the water mass with each of the air diffusion systems was evaluated
comparatively. The oxygen concentration was determined by optical
sensors with data logging. The experimental data was analyzed
comparatively for all three different air dispersion systems aiming to
identify the oxygen concentration variation during different
operational conditions. The Oxygenation Capacity was calculated for
each of the three systems and used as performance and selection
parameter. The global mass transfer coefficients were also evaluated
as important tools in designing the aeration system. Even though
using the tubular porous diffusers leads to higher oxygen
concentration compared to the perforated pipe system (which
provides medium-sized bubbles in the aqueous solution), it doesn’t
achieve the threshold limit of 80% oxygen saturation in less than 30
minutes. The study has shown that the optimal solution for the
studied configuration was the radial air diffusers which ensure an
oxygen saturation of 80% in 20 minutes. An increment of the values
was identified when the air flow was increased.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.
Abstract: The present study applies the inverse method and
three-dimensional CFD commercial software in conjunction with the
experimental temperature data to investigate the heat transfer and fluid
flow characteristics of the plate-fin heat sink in a rectangular closed
enclosure. The inverse method with the finite difference method and
the experimental temperature data is applied to determine the
approximate heat transfer coefficient. Later, based on the obtained
results, the zero-equation turbulence model is used to obtain the heat
transfer and fluid flow characteristics between two fins. T0 validate
the accuracy of the results obtained, the comparison of the heat transfer
coefficient is made. The obtained temperature at selected
measurement locations of the fin is also compared with experimental
data. The effect of the height of the rectangular enclosure on the
obtained results is discussed.
Abstract: The Northeast China (NEC) was the most important
agriculture areas and known as the Golden-Maize-Belt. Based on
observed crop data and crop model, we design four simulating
experiments and separate relative impacts and contribution under
climate change, planting date shift, and varieties change as well
change of varieties and planting date. Without planting date and
varieties change, maize yields had no significant change trend at
Hailun station located in the north of NEC, and presented significant
decrease by 0.2 - 0.4 t/10a at two stations, which located in the middle
and the south of NEC. With planting date change, yields showed a
significant increase by 0.09 - 0.47 t/10a. With varieties change, maize
yields had significant increase by 1.8~ 1.9 t/10a at Hailun and Huadian
stations, but a non-significant and low increase by 0.2t /10a at Benxi
located in the south of NEC. With change of varieties and planting
date, yields presented a significant increasing by 0.53- 2.0 t/10a. Their
contribution to yields was -25% ~ -55% for climate change, 15% ~
35% for planting date change, and 20% ~110% for varieties change as
well 30% ~135% for varieties with planting date shift. It found that
change in varieties and planting date were highest yields and were
responsible for significant increases in maize yields, varieties was
secondly, and planting date was thirdly. It found that adaptation in
varieties and planting date greatly improved maize yields, and
increased yields annual variability. The increase of contribution with
planting date and varieties change in 2000s was lower than in 1990s.
Yields with the varieties change and yields with planting date and
varieties change all showed a decreasing trend at Huadian and Benxi
since 2002 or so. It indicated that maize yields increasing trend
stagnated in the middle and south of NEC, and continued in the north
of NEC.