Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: The purpose of this study is to introduce a new
interface program to calculate a dose distribution with Monte Carlo method in complex heterogeneous systems such as organs or tissues
in proton therapy. This interface program was developed under
MATLAB software and includes a friendly graphical user interface
with several tools such as image properties adjustment or results display. Quadtree decomposition technique was used as an image
segmentation algorithm to create optimum geometries from Computed Tomography (CT) images for dose calculations of proton
beam. The result of the mentioned technique is a number of nonoverlapped
squares with different sizes in every image. By this way
the resolution of image segmentation is high enough in and near
heterogeneous areas to preserve the precision of dose calculations
and is low enough in homogeneous areas to reduce the number of
cells directly. Furthermore a cell reduction algorithm can be used to combine neighboring cells with the same material. The validation of this method has been done in two ways; first, in comparison with experimental data obtained with 80 MeV proton beam in Cyclotron
and Radioisotope Center (CYRIC) in Tohoku University and second, in comparison with data based on polybinary tissue calibration method, performed in CYRIC. These results are presented in this paper. This program can read the output file of Monte Carlo code while region of interest is selected manually, and give a plot of dose distribution of proton beam superimposed onto the CT images.
Abstract: Drilling is the most common machining operation and it forms the highest machining cost in many manufacturing activities including automotive engine production. The outcome of this operation depends upon many factors including utilization of proper cutting tool geometry, cutting tool material and the type of coating used to improve hardness and resistance to wear, and also cutting parameters. With the availability of a large array of tool geometries, materials and coatings, is has become a challenging task to select the best tool and cutting parameters that would result in the lowest machining cost or highest profit rate. This paper describes an algorithm developed to help achieve good performances in drilling operations by automatically determination of proper cutting tools and cutting parameters. It also helps determine machining sequences resulting in minimum tool changes that would eventually reduce machining time and cost where multiple tools are used.
Abstract: The present article comprises a theoretical study of
structures Performat radical (HCO3) with H2O molecule. We make
use of ab initio quantum chemical methods. Unrestricted Hartee-Fock
(UHF) with the basis set6-311+g(2df,2p) and density functional
theory (B3LYP) with the basis set 6-311+g(2df,2p) and also we done
atoms in molecules (AIM) theory for them. We have found four
stable geometries the PerformatRadical(HCO3) with H2O.
Abstract: The algorithms of convex hull have been extensively studied in literature, principally because of their wide range of applications in different areas. This article presents an efficient algorithm to construct approximate convex hull from a set of n points in the plane in O(n + k) time, where k is the approximation error control parameter. The proposed algorithm is suitable for applications preferred to reduce the computation time in exchange of accuracy level such as animation and interaction in computer graphics where rapid and real-time graphics rendering is indispensable.
Abstract: In this paper, at first we explain about negative
hypergeometric distribution and its properties. Then we use the w-function
and the Stein identity to give a result on the poisson
approximation to the negative hypergeometric distribution in terms of the total variation distance between the negative hypergeometric and
poisson distributions and its upper bound.
Abstract: A chord of a simple polygon P is a line segment [xy]
that intersects the boundary of P only at both endpoints x and y. A
chord of P is called an interior chord provided the interior of [xy] lies
in the interior of P. P is weakly visible from [xy] if for every point v
in P there exists a point w in [xy] such that [vw] lies in P. In this
paper star-shaped, L-convex, and convex polygons are characterized
in terms of weak visibility properties from internal chords and starshaped
subsets of P. A new Krasnoselskii-type characterization of
isothetic star-shaped polygons is also presented.
Abstract: Explosive forming is one of the unconventional
techniques in which, most commonly, the water is used as the
pressure transmission medium. One of the newest methods in
explosive forming is gas detonation forming which uses a normal
shock wave derived of gas detonation, to form sheet metals. For this
purpose a detonation is developed from the reaction of H2+O2
mixture in a long cylindrical detonation tube. The detonation wave
goes through the detonation tube and acts as a blast load on the steel
blank and forms it. Experimental results are compared with a finite
element model; and the comparison of the experimental and
numerical results obtained from strain, thickness variation and
deformed geometry is carried out. Numerical and experimental
results showed approximately 75 – 90 % similarity in formability of
desired shape. Also optimum percent of gas mixture obtained when
we mix 68% H2 with 32% O2.
Abstract: This paper describes an automatic algorithm to restore
the shape of three-dimensional (3D) left ventricle (LV) models created
from magnetic resonance imaging (MRI) data using a geometry-driven
optimization approach. Our basic premise is to restore the LV shape
such that the LV epicardial surface is smooth after the restoration. A
geometrical measure known as the Minimum Principle Curvature (κ2)
is used to assess the smoothness of the LV. This measure is used to
construct the objective function of a two-step optimization process.
The objective of the optimization is to achieve a smooth epicardial
shape by iterative in-plane translation of the MRI slices.
Quantitatively, this yields a minimum sum in terms of the magnitude
of κ
2, when κ2 is negative. A limited memory quasi-Newton algorithm,
L-BFGS-B, is used to solve the optimization problem. We tested our
algorithm on an in vitro theoretical LV model and 10 in vivo
patient-specific models which contain significant motion artifacts. The
results show that our method is able to automatically restore the shape
of LV models back to smoothness without altering the general shape of
the model. The magnitudes of in-plane translations are also consistent
with existing registration techniques and experimental findings.
Abstract: The aim of this research is to design a collaborative
framework that integrates risk analysis activities into the geospatial
database design (GDD) process. Risk analysis is rarely undertaken
iteratively as part of the present GDD methods in conformance to
requirement engineering (RE) guidelines and risk standards.
Accordingly, when risk analysis is performed during the GDD, some
foreseeable risks may be overlooked and not reach the output
specifications especially when user intentions are not systematically
collected. This may lead to ill-defined requirements and ultimately in
higher risks of geospatial data misuse. The adopted approach consists
of 1) reviewing risk analysis process within the scope of RE and
GDD, 2) analyzing the challenges of risk analysis within the context
of GDD, and 3) presenting the components of a risk-based
collaborative framework that improves the collection of the
intended/forbidden usages of the data and helps geo-IT experts to
discover implicit requirements and risks.
Abstract: The condition of lightning surge causes the traveling waves and the temporary increase in voltage in the transmission line system. Lightning is the most harmful for destroying the transmission line and setting devices so it is necessary to study and analyze the temporary increase in voltage for designing and setting the surge arrester. This analysis describes the figure of the lightning wave in transmission line with 115 kV voltage level in Thailand by using ATP/EMTP program to create the model of the transmission line and lightning surge. Because of the limit of this program, it must be calculated for the geometry of the transmission line and surge parameter and calculation in the manual book for the closest value of the parameter. On the other hand, for the effects on surge protector when the lightning comes, the surge arrester model must be right and standardized as metropolitan electrical authority's standard. The candidate compared the real information to the result from calculation, also. The results of the analysis show that the temporary increase in voltage value will be rise to 326.59 kV at the line which is done by lightning when the surge arrester is not set in the system. On the other hand, the temporary increase in voltage value will be 182.83 kV at the line which is done by lightning when the surge arrester is set in the system and the period of the traveling wave is reduced, also. The distance for setting the surge arrester must be as near to the transformer as possible. Moreover, it is necessary to know the right distance for setting the surge arrester and the size of the surge arrester for preventing the temporary increase in voltage, effectively.
Abstract: This paper applies an anthropological approach to illuminate the dynamic cultural geography of Kazakhstani Korean ethnicity focusing on its turning point, the historic “Seoul Olympic Games in 1988." The Korean ethnic group was easily considered as a harmonious and homogeneous community by outsiders, but there existed deep-seated conflicts and hostilities within the ethnic group. The majority-s oppositional dichotomy of superiority and inferiority toward the minority was continuously reorganized and reinforced by difference in experience, memory and sentiment. However, such a chronic exclusive boundary was collapsed following the patriotism ignited by the Olympics held in their mother country. This paper explores the fluidity of subject by formation of the boundary in which constructed cultural differences are continuously essentialized and reproduced, and by dissolution of cultural barrier in certain contexts.
Abstract: In this work, bending fatigue life of notched
specimens with various notch geometries and dimensions is
investigated by experiment and Manson-Caffin theoretical method. In
this theoretical method, fatigue life of notched specimens is
calculated using the fatigue life obtained from the experiments for
plain specimens (without notch). Three notch geometries including
∪-shape, ∨-shape and C -shape notches are considered in this
investigation. The experiments are conducted on a rotary bending
Moore machine. The specimens are made of a low carbon steel alloy,
which has wide application in industry. The stress- life curves are
captured for all notched specimen by experiment. The results indicate
that Manson-Caffin analytical method cannot adequately predict
the fatigue life of notched specimen. However, it seems that the
difference between the experiments and Manson-Caffin predictions
can be compensated by a proportional factor.
Abstract: In this paper, the effects of thermodynamic,
hydrodynamic and geometric of an air cooled condenser on COP of
vapor compression cycle are investigated for a fixed condenser facing
surface area. The system is utilized with a scroll compressor,
modeled based on thermodynamic and heat transfer equations
employing Matlab software. The working refrigerant is R134a whose
thermodynamic properties are called from Engineering Equation
Software. This simulation shows that vapor compression cycle can
be designed by different configurations and COPs, economical and
optimum working condition can be obtained via considering these
parameters.
Abstract: This paper presents the findings of an
experimental investigation to study the effect of alkali content
in geopolymer mortar specimens exposed to sulphuric acid.
Geopolymer mortar specimens were manufactured from Class F fly
ash by activation with a mixture of sodium hydroxide and sodium
silicate solution containing 5% to 8% Na2O. Durability of specimens
were assessed by immersing them in 10% sulphuric acid solution and
periodically monitoring surface deterioration and depth of
dealkalization, changes in weight and residual compressive strength
over a period of 24 weeks. Microstructural changes in the specimens
were studied with Scanning electron microscopy (SEM) and EDAX.
Alkali content in the activator solution significantly affects the
durability of fly ash based geopolymer mortars in sulphuric acid.
Specimens manufactured with higher alkali content performed better
than those manufactured with lower alkali content. After 24 weeks in
sulphuric acid, specimen with 8% alkali still recorded a residual
strength as high as 55%.
Abstract: The paper outlines the relevance of computational
geometry within the design and production process of architecture.
Based on two case studies, the digital chain - from the initial formfinding
to the final realization of spatial concepts - is discussed in
relation to geometric principles. The association with the fascinating
complexity that can be found in nature and its underlying geometry
was the starting point for both projects presented in the paper. The
translation of abstract geometric principles into a three-dimensional
digital design model – realized in Rhinoceros – was followed by a
process of transformation and optimization of the initial shape that
integrated aesthetic, spatial and structural qualities as well as aspects
of material properties and conditions of production.
Abstract: Rarefied gas flows are often occurred in micro electro
mechanical systems and classical CFD could not precisely anticipate
the flow and thermal behavior due to the high Knudsen number.
Therefore, the heat transfer and the fluid dynamics characteristics of
rarefied gas flows in both a two-dimensional simple microchannel
and geometry similar to single Knudsen compressor have been
investigated with a goal of increasing performance of a actual
Knudsen compressor by using a particle simulation method. Thermal
transpiration and thermal creep, which are rarefied gas dynamic
phenomena, that cause movement of the flow from less to higher
temperature is generated by using two different longitude temperature
gradients (Linear, Step) along the walls of the flow microchannel. In
this study the influence of amount of temperature gradient and
governing pressure in various Knudsen numbers and length-to-height
ratios have been examined.
Abstract: Higher-order Statistics (HOS), also known as
cumulants, cross moments and their frequency domain counterparts,
known as poly spectra have emerged as a powerful signal processing
tool for the synthesis and analysis of signals and systems. Algorithms
used for the computation of cross moments are computationally
intensive and require high computational speed for real-time
applications. For efficiency and high speed, it is often advantageous
to realize computation intensive algorithms in hardware. A promising
solution that combines high flexibility together with the speed of a
traditional hardware is Field Programmable Gate Array (FPGA). In
this paper, we present FPGA-based parallel architecture for the
computation of third-order cross moments. The proposed design is
coded in Very High Speed Integrated Circuit (VHSIC) Hardware
Description Language (VHDL) and functionally verified by
implementing it on Xilinx Spartan-3 XC3S2000FG900-4 FPGA.
Implementation results are presented and it shows that the proposed
design can operate at a maximum frequency of 86.618 MHz.
Abstract: A dent is a gross distortion of the pipe cross-section.
Dent depth is defined as the maximum reduction in the diameter of
the pipe compared to the original diameter. Pipeline dent finite
element (FE) simulation and theoretical analysis are conducted in this
paper to develop an understanding of the geometric characteristics
and strain distribution in the pressurized dented pipe. Based on the
results, the magnitude of the denting force increases significantly
with increasing the internal pressure, and the maximum
circumferential and longitudinal strains increase by increasing the
internal pressure and the dent depth. The results can be used for
characterizing dents and ranking their risks to the integrity of a
pipeline.
Abstract: This paper describes a method of modeling to model
shadow play puppet using sophisticated computer graphics techniques
available in OpenGL in order to allow interactive play in real-time
environment as well as producing realistic animation. This paper
proposes a novel real-time method is proposed for modeling of puppet
and its shadow image that allows interactive play of virtual shadow
play using texture mapping and blending techniques. Special effects
such as lighting and blurring effects for virtual shadow play
environment are also developed. Moreover, the use of geometric
transformations and hierarchical modeling facilitates interaction
among the different parts of the puppet during animation. Based on the
experiments and the survey that were carried out, the respondents
involved are very satisfied with the outcomes of these techniques.