Abstract: Gasoline Octane Number is the standard measure of
the anti-knock properties of a motor in platforming processes, that is
one of the important unit operations for oil refineries and can be
determined with online measurement or use CFR (Cooperative Fuel
Research) engines. Online measurements of the Octane number can
be done using direct octane number analyzers, that it is too
expensive, so we have to find feasible analyzer, like ANFIS
estimators.
ANFIS is the systems that neural network incorporated in fuzzy
systems, using data automatically by learning algorithms of NNs.
ANFIS constructs an input-output mapping based both on human
knowledge and on generated input-output data pairs.
In this research, 31 industrial data sets are used (21 data for training
and the rest of the data used for generalization). Results show that,
according to this simulation, hybrid method training algorithm in
ANFIS has good agreements between industrial data and simulated
results.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: In recent years, environment regulation forcing
manufactures to consider recovery activity of end-of- life products
and/or return products for refurbishing, recycling,
remanufacturing/repair and disposal in supply chain management. In
this paper, a mathematical model is formulated for single product
production-inventory system considering remanufacturing/reuse of
return products and rate of return products follows a demand like
function, dependent on purchasing price and acceptance quality level.
It is useful in decision making to determine whether to go for
remanufacturing or disposal of returned products along with newly
produced products to satisfy a stationary demand. In addition, a
modified genetic algorithm approach is proposed, inspired by particle
swarm optimization method. Numerical analysis of the case study is
carried out to validate the model.
Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.
Abstract: The study describes chitosan membrane platform
modified with nanostructure pattern which using nanotechnology to
fabricate. The cell-substrate interaction between neuro-2a neuroblasts
cell lines and chitosan membrane (flat, nanostructure and
nanostructure pattern types) was investigated. The adhered
morphology of neuro-2a cells depends on the topography of chitosan
surface. We have found that neuro-2a showed different morphogenesis
when cells adhered on flat and nanostructure chitosan membrane. The
cell projected area of neuro-2a on flat chitosan membrane is larger
than on nanostructure chitosan membrane. In addition, neuro-2a cells
preferred to adhere on flat chitosan surface region than on
nanostructure chitosan membrane to immobilize and differentiation.
The experiment suggests surface topography can be used as a critical
mechanism to isolate group of neuro-2a to a particular rectangle area
on chitosan membrane. Our finding will provide a platform to take
patch clamp to record electrophysiological behavior about neurons in
vitro in the future.
Abstract: Rapid Application Development (RAD) enables ever
expanding needs for speedy development of computer application
programs that are sophisticated, reliable, and full-featured. Visual
Basic was the first RAD tool for the Windows operating system, and
too many people say still it is the best. To provide very good
attraction in visual basic 6 applications, this paper directing to use
VRML scenes over the visual basic environment.
Abstract: In this paper we present two novel 1-bit full adder
cells in dynamic logic style. NP-CMOS (Zipper) and Multi-Output
structures are used to design the adder blocks. Characteristic of
dynamic logic leads to higher speeds than the other standard static
full adder cells. Using HSpice and 0.18┬Ám CMOS technology
exhibits a significant decrease in the cell delay which can result in a
considerable reduction in the power-delay product (PDP). The PDP
of Multi-Output design at 1.8v power supply is around 0.15 femto
joule that is 5% lower than conventional dynamic full adder cell and
at least 21% lower than other static full adders.
Abstract: This paper develops driver reaction-time models for
car-following analysis based on human factors. The reaction time
was classified as brake-reaction time (BRT) and
acceleration/deceleration reaction time (ADRT). The BRT occurs
when the lead vehicle is barking and its brake light is on, while the
ADRT occurs when the driver reacts to adjust his/her speed using the
gas pedal only. The study evaluates the effect of driver
characteristics and traffic kinematic conditions on the driver reaction
time in a car-following environment. The kinematic conditions
introduced urgency and expectancy based on the braking behaviour
of the lead vehicle at different speeds and spacing. The kinematic
conditions were used for evaluating the BRT and are classified as
normal, surprised, and stationary. Data were collected on a driving
simulator integrated into a real car and included the BRT and ADRT
(as dependent variables) and driver-s age, gender, driving experience,
driving intensity (driving hours per week), vehicle speed, and
spacing (as independent variables). The results showed that there was
a significant difference in the BRT at normal, surprised, and
stationary scenarios and supported the hypothesis that both urgency
and expectancy had significant effects on BRT. Driver-s age, gender,
speed, and spacing were found to be significant variables for the
BRT in all scenarios. The results also showed that driver-s age and
gender were significant variables for the ADRT. The research
presented in this paper is part of a larger project to develop a driversensitive
in-vehicle rear-end collision warning system.
Abstract: The fuzzy set theory has been applied in many fields,
such as operations research, control theory, and management
sciences, etc. In particular, an application of this theory in decision
making problems is linear programming problems with fuzzy
numbers. In this study, we present a new method for solving fuzzy
number linear programming problems, by use of linear ranking
function. In fact, our method is similar to simplex method that was
used for solving linear programming problems in crisp environment
before.
Abstract: ICA which is generally used for blind source separation
problem has been tested for feature extraction in Speech recognition
system to replace the phoneme based approach of MFCC. Applying
the Cepstral coefficients generated to ICA as preprocessing has
developed a new signal processing approach. This gives much better
results against MFCC and ICA separately, both for word and speaker
recognition. The mixing matrix A is different before and after MFCC
as expected. As Mel is a nonlinear scale. However, cepstrals
generated from Linear Predictive Coefficient being independent
prove to be the right candidate for ICA. Matlab is the tool used for
all comparisons. The database used is samples of ISOLET.
Abstract: Technology changes have been acknowledged as a
critical factor in determining competitiveness of organization. Under
such environment, the right anticipation of technology change has
been of huge importance in strategic planning. To monitor technology
change, technology forecasting (TF) is frequently utilized. In
academic perspective, TF has received great attention for a long time.
However, few researches have been conducted to provide overview of
the TF literature. Even though some studies deals with review of TF
research, they generally focused on type and characteristics of various
TF, so hardly provides information about patterns of TF research and
which TF method is used in certain technology industry. Accordingly,
this study profile developments in and patterns of scholarly research in
TF over time. Also, this study investigates which technology
industries have used certain TF method and identifies their
relationships. This study will help in understanding TF research trend
and their application area.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: Solar water heating (SWH) systems are gaining popularity in ASEAN in the midst of increasing number of affluent population in society and environmental concerns from seemingly unchanged reliance on fossil-based fuels. The penetration of these systems and technologies into ASEAN markets is a welcome development; however there is a need for the method of assessment of their thermal performances. This paper discusses the reasons for this need and a suitable method for thermal performance evaluation of SWH systems in ASEAN. The paper also calls on research to be focused on the establishment of reliable data to be entered into the performance rating software. The establishment of accredited solar systems testing facilities can help boost the competitiveness of ASEAN solar industry.
Abstract: This paper identifies five key design characteristics of
production scheduling software systems in printed circuit board (PCB) manufacturing. The authors consider that, in addition to an effective scheduling engine, a scheduling system should be able to
process a preventative maintenance calendar, to give the user the
flexibility to handle data using a variety of electronic sources, to run
simulations to support decision-making, and to have simple and
customisable graphical user interfaces. These design considerations
were the result of a review of academic literature, the evaluation of
commercial applications and a compilation of requirements of a PCB manufacturer. It was found that, from those systems that were evaluated, those that effectively addressed all five characteristics
outlined in this paper were the most robust of all and could be used in
PCB manufacturing.
Abstract: This paper focuses on the 3D reconstruction of
the architectural design of Darul Ridzuan Museum. It has
concentrated on designing exterior part of the building according
to colored digital photo of the real museum. Besides viewing the
architecture, walkthroughs are generated for the user to control
it in an easier way. User can travel through the museum to get
the feel of the environment and to explore the design of the
museum as a whole; both exterior and interior. The result has
shown positive result in terms of realism, navigation, collision
detection, suitability, usability and user-s acceptance. In brief,
the 3D virtual museum has provided an alternative to present a
real museum.
Abstract: Application of wood in rural construction is diffused
all around the world since remote times. However, its inclusion in
structural design deserves strong support from broad knowledge of
material properties. The pertinent literature reveals the application of
optical methods in determining the complete field displacement on
bodies exhibiting regular as well as irregular surfaces. The use of
moiré techniques in experimental mechanics consists in analyzing the
patterns generated on the body surface before and after deformation.
The objective of this research work is to study the qualitative
deformation behavior of wooden testing specimens under specific
loading situations. The experiment setup follows the literature
description of shadow moiré methods. Results indicate strong
anisotropy influence of the generated displacement field. Important
qualitative as well as quantitative stress and strain distribution were
obtained wooden members which are applicable to rural
constructions.
Abstract: De novo genome assembly is always fragmented. Assembly fragmentation is more serious using the popular next generation sequencing (NGS) data because NGS sequences are shorter than the traditional Sanger sequences. As the data throughput of NGS is high, the fragmentations in assemblies are usually not the result of missing data. On the contrary, the assembled sequences, called contigs, are often connected to more than one other contigs in a complicated manner, leading to the fragmentations. False connections in such complicated connections between contigs, named a contig graph, are inevitable because of repeats and sequencing/assembly errors. Simplifying a contig graph by removing false connections directly improves genome assembly. In this work, we have developed a tool, SIMGraph, to resolve ambiguous connections between contigs using NGS data. Applying SIMGraph to the assembly of a fungus and a fish genome, we resolved 27.6% and 60.3% ambiguous contig connections, respectively. These results can reduce the experimental efforts in resolving contig connections.
Abstract: Construction of tunnels is connected with high
uncertainty in the field of costs, construction period, safety and
impact on surroundings. Risk management became therefore a
common part of tunnel projects, especially after a set of fatal
collapses occurred in 1990's. Such collapses are caused usually by
combination of factors that can be divided into three main groups, i.e.
unfavourable geological conditions, failures in the design and
planning or failures in the execution.
This paper suggests a procedure enabling quantification of the
excavation risk related to extraordinary accidents using FTA and
ETA tools. It will elaborate on a common process of risk analysis and
enable the transfer of information and experience between particular
tunnel construction projects. Further, it gives a guide for designers,
management and other participants, how to deal with risk of such
accidents and how to make qualified decisions based on a
probabilistic approach.
Abstract: In this work, we experimentally study heat transfer
from exhaust particulate air of detergent spray drying tower to water
by using coiled tube heat exchanger. Water flows in the coiled
tubes, where air loaded with detergent particles of 43 micrometers
in diameter flows within the shell. Four coiled tubes with different
coil pitches are used in a counter-current flow configuration. We
investigate heat transfer coefficients of inside and outside the heat
transfer surfaces through 400 experiments. The correlations between
Nusselt number and Reynolds number, Prandtl number, mass flow
rate of particulates to mass flow rate of air ratio and coiled tube
pitch parameter are proposed. The correlations procured can be used
to predicted heat transfer between tube and shell of the heat
exchanger.
Abstract: Rapid enlargement and physical development of cities
have facilitated the emergence of a number of city life crises and
decrease of environment quality. Subsequently, the need for noticing
the concept of quality and its improvement in urban environments,
besides quantitative issues, is obviously recognized. In the domain of
urban ideas the importance of taking these issues into consideration
is obvious not only in accordance to sustainable development
concepts and improvement of public environment quality, but also in
the enhancement of social and behavioral models.
The major concern of present article is to study the nature of urban
environment quality in urban development plans, which is important
not only in the concept and the aim of projects but also in their
execution procedure. As a result, this paper is going to utilize
planning capacities caused by environmental virtues in the planning
procedure of Moft Abad neighborhood. Thus, at the first step,
applying the Analytical Hierarchy Process (AHP), it has assessed
quantitative environmental issues. The present conditions of Moft
Abad state that “the neighborhood is generally suffering from the
lack of qualitative parameters, and the previously formed planning
procedures could not take the sustainable and developmental paths
which are aimed at environment quality virtues." The diminution of
economical and environmental virtues has resulted in the diminution
of residential and social virtues. Therefore, in order to enhance the
environment quality in Moft Abad, the present paper has tried to
supply the subject plans in order to make a safe, healthy, and lively
neighborhood.