Abstract: A method is presented for using thermo-mechanical fatigue analysis as a tool in the design of automotive heat exchangers. Use of infra-red thermography to measure the real thermal history in the heat exchanger reduces the time necessary for calculating design parameters and improves prediction accuracy. Thermal shocks are the primary cause of heat exchanger damage. Thermo-mechanical simulation is based on the mean behavior of the aluminum tubes used in the heat exchanger. An energetic fatigue criterion is used to detect critical zones.
Abstract: Because support interference corrections are not properly
understood, engineers mostly rely on expensive dummy measurements
or CFD calculations. This paper presents a method based on uncorrected wind tunnel measurements and fast calculation techniques
(it is a hybrid method) to calculate wall interference, support interference and residual interference (when e.g. a support member
closely approaches the wind tunnel walls) for any type of wind tunnel and support configuration. The method provides with a simple formula
for the calculation of the interference gradient. This gradient is
based on the uncorrected measurements and a successive calculation
of the slopes of the interference-free aerodynamic coefficients. For the latter purpose a new vortex-lattice routine is developed that corrects
the slopes for viscous effects. A test case of a measurement on a wing proves the value of this hybrid method as trends and orders of
magnitudes of the interference are correctly determined.
Abstract: Water quality is a subject of ongoing concern.
Deterioration of water quality has initiated serious management
efforts in many countries. This study endeavors to automatically
classify water quality. The water quality classes are evaluated using 6
factor indices. These factors are pH value (pH), Dissolved Oxygen
(DO), Biochemical Oxygen Demand (BOD), Nitrate Nitrogen
(NO3N), Ammonia Nitrogen (NH3N) and Total Coliform (TColiform).
The methodology involves applying data mining
techniques using multilayer perceptron (MLP) neural network
models. The data consisted of 11 sites of canals in Dusit district in
Bangkok, Thailand. The data is obtained from the Department of
Drainage and Sewerage Bangkok Metropolitan Administration
during 2007-2011. The results of multilayer perceptron neural
network exhibit a high accuracy multilayer perception rate at 96.52%
in classifying the water quality of Dusit district canal in Bangkok
Subsequently, this encouraging result could be applied with plan and
management source of water quality.
Abstract: In this paper, optimal generation expansion planning (GEP) is investigated considering purchase prices, profits of independent power producers (IPPs) and reliability criteria using a new method based on hybrid coded Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). In this approach, optimal purchase price of each IPP is obtained by HCGA and reliability criteria are calculated by PSO technique. It should be noted that reliability criteria and the rate of carbon dioxide (CO2) emission have been considered as constraints of the GEP problem. Finally, the proposed method has been tested on the case study system. The results evaluation show that the proposed method can simply obtain optimal purchase prices of IPPs and is a fast method for calculation of reliability criteria in expansion planning. Also, considering the optimal purchase prices and profits of IPPs in generation expansion planning are caused that the expansion costs are decreased and the problem is solved more exactly.
Abstract: The study on the tree growth for four species groups of commercial timber in Koh Kong province, Cambodia-s tropical rainforest is described. The simulation for these four groups had been successfully developed in the 5-year interval through year-60. Data were obtained from twenty permanent sample plots in the duration of thirteen years. The aim for this study was to develop stand table simulation system of tree growth by the species group. There were five steps involved in the development of the tree growth simulation: aggregate the tree species into meaningful groups by using cluster analysis; allocate the trees in the diameter classes by the species group; observe the diameter movement of the species group. The diameter growth rate, mortality rate and recruitment rate were calculated by using some mathematical formula. Simulation equation had been created by combining those parameters. Result showed the dissimilarity of the diameter growth among species groups.
Abstract: Campus sustainability is the goal of a university striving for sustainable development. This study found that of 17 popular approaches, two comprehensive campus sustainability assessment frameworks were developed in the context of Sustainability in Higher Education (SHE), and used by many university campuses around the world. Sustainability Tracking Assessment and Rating Systems (STARS) and the Campus Sustainability Assessment Framework (CSAF) approaches are more comprehensive than others. Therefore, the researchers examined aspects and elements used by CSAF and STARS in the approach to develop a campus sustainability assessment framework for Universiti Kebangsaan Malaysia (UKM). Documents analysis found that CSAF and STARS do not focus on physical development, especially the construction industry, as key elements of campus sustainability assessment. This finding is in accordance with the Sustainable UKM Programme which consists of three main components of sustainable community, ecosystem and physical development.
Abstract: Present wireless communication demands compact and intelligent devices with multitasking capabilities at affordable cost. The focus in the presented paper is on a dual band antenna for wireless communication with the capability of operating at two frequency bands with same structure. Two resonance frequencies are observed with the second operation band at 4.2GHz approximately three times the first resonance frequency at 1.5GHz. Structure is simple loop of microstrip line with characteristic impedance 50 ohms. The proposed antenna is designed using defective ground structure (DGS) and shows the nearly one third reductions in size as compared to without DGS. This antenna was simulated on electromagnetic (EM) simulation software and fabricated using microwave integrated circuit technique on RT-Duroid dielectric substrate (εr= 2.22) of thickness (H=15 mils). The designed antenna was tested on automatic network analyzer and shows the good agreement with simulated results. The proposed structure is modeled into an equivalent electrical circuit and simulated on circuit simulator. Subsequently, theoretical analysis was carried out and simulated. The simulated, measured, equivalent circuit response, and theoretical results shows good resemblance. The bands of operation draw many potential applications in today’s wireless communication.
Abstract: Artificial Bee Colony (ABC) algorithm is a relatively new swarm intelligence technique for clustering. It produces higher
quality clusters compared to other population-based algorithms but with poor energy efficiency, cluster quality consistency and typically slower in convergence speed. Inspired by energy saving foraging behavior of natural honey bees this paper presents a Quality and Quantity Aware Artificial Bee Colony (Q2ABC) algorithm to improve quality of cluster identification, energy efficiency and convergence speed of the original ABC. To evaluate the performance of Q2ABC algorithm, experiments were conducted on a suite of ten benchmark UCI datasets. The results demonstrate Q2ABC outperformed ABC and K-means algorithm in the quality of clusters delivered.
Abstract: In biological and biomedical research motif finding tools are important in locating regulatory elements in DNA sequences. There are many such motif finding tools available, which often yield position weight matrices and significance indicators. These indicators, p-values and E-values, describe the likelihood that a motif alignment is generated by the background process, and the expected number of occurrences of the motif in the data set, respectively. The various tools often estimate these indicators differently, making them not directly comparable. One approach for comparing motifs from different tools, is computing the E-value as the product of the p-value and the number of possible alignments in the data set. In this paper we explore the combinatorics of the motif alignment models OOPS, ZOOPS, and ANR, and propose a generic algorithm for computing the number of possible combinations accurately. We also show that using the wrong alignment model can give E-values that significantly diverge from their true values.
Abstract: Avoiding learning failures in mathematics e-learning environments caused by emotional problems in students with autism has become an important topic for combining of special education with information and communications technology. This study presents an adaptive emotional adjustment model in mathematics e-learning for students with autism, emphasizing the lack of emotional perception in mathematics e-learning systems. In addition, an emotion classification for students with autism was developed by inducing emotions in mathematical learning environments to record changes in the physiological signals and facial expressions of students. Using these methods, 58 emotional features were obtained. These features were then processed using one-way ANOVA and information gain (IG). After reducing the feature dimension, methods of support vector machines (SVM), k-nearest neighbors (KNN), and classification and regression trees (CART) were used to classify four emotional categories: baseline, happy, angry, and anxious. After testing and comparisons, in a situation without feature selection, the accuracy rate of the SVM classification can reach as high as 79.3-%. After using IG to reduce the feature dimension, with only 28 features remaining, SVM still has a classification accuracy of 78.2-%. The results of this research could enhance the effectiveness of eLearning in special education.
Abstract: A gene network gives the knowledge of the regulatory
relationships among the genes. Each gene has its activators and
inhibitors that regulate its expression positively and negatively
respectively. Genes themselves are believed to act as activators and
inhibitors of other genes. They can even activate one set of genes and
inhibit another set. Identifying gene networks is one of the most
crucial and challenging problems in Bioinformatics. Most work done
so far either assumes that there is no time delay in gene regulation or
there is a constant time delay. We here propose a Dynamic Time-
Lagged Correlation Based Method (DTCBM) to learn the gene
networks, which uses time-lagged correlation to find the potential
gene interactions, and then uses a post-processing stage to remove
false gene interactions to common parents, and finally uses dynamic
correlation thresholds for each gene to construct the gene network.
DTCBM finds correlation between gene expression signals shifted in
time, and therefore takes into consideration the multi time delay
relationships among the genes. The implementation of our method is
done in MATLAB and experimental results on Saccharomyces
cerevisiae gene expression data and comparison with other methods
indicate that it has a better performance.
Abstract: In this research work, poly (acrylonitrile-butadienestyrene)/
polypropylene (ABS/PP) blends were processed by melt
compounding in a twin-screw extruder. Upgrading of the thermal
characteristics of the obtained materials was attempted by the
incorporation of organically modified montmorillonite (OMMT), as
well as, by the addition of two types of compatibilizers;
polypropylene grafted with maleic anhydride (PP-g-MAH) and ABS
grafted with maleic anhydride (ABS-g-MAH). The effect of the
above treatments was investigated separately and in combination.
Increasing the PP content in ABS matrix seems to increase the
thermal stability of their blend and the glass transition temperature
(Tg) of SAN phase of ABS. From the other part, the addition of ABS
to PP promotes the formation of its β-phase, which is maximum at 30
wt% ABS concentration, and increases the crystallization temperature
(Tc) of PP. In addition, it increases the crystallization rate of PP.The
β-phase of PP in ABS/PP blends is reduced by the addition of
compatibilizers or/and organoclay reinforcement. The incorporation
of compatibilizers increases the thermal stability of PP and reduces
its melting (ΔΗm) and crystallization (ΔΗc) enthalpies. Furthermore it
decreases slightly the Tgs of PP and SAN phases of ABS/PP blends.
Regarding the storage modulus of the ABS/PP blends, it presents a
change in their behavior at about 10°C and return to their initial
behavior at ~110°C. The incorporation of OMMT to no compatibilized
and compatibilized ABS/PP blends enhances their storage modulus.
Abstract: Robustness is one of the primary performance criteria for an Intelligent Video Surveillance (IVS) system. One of the key factors in enhancing the robustness of dynamic video analysis is,providing accurate and reliable means for shadow detection. If left undetected, shadow pixels may result in incorrect object tracking and classification, as it tends to distort localization and measurement information. Most of the algorithms proposed in literature are computationally expensive; some to the extent of equalling computational requirement of motion detection. In this paper, the homogeneity property of shadows is explored in a novel way for shadow detection. An adaptive division image (which highlights homogeneity property of shadows) analysis followed by a relatively simpler projection histogram analysis for penumbra suppression is the key novelty in our approach.
Abstract: This work aims to describe the process of developing
services and applications of seamless communication within a
Telecom Italia long-term research project, which takes as central aim
the design of a wearable communication device. In particular, the
objective was to design a wrist phone integrated into everyday life of
people in full transparency. The methodology used to design the
wristwatch was developed through several subsequent steps also
involving the Personas Layering Framework. The data collected in
this phases have been very useful for designing an improved version
of the first two concepts of wrist phone going to change aspects
related to the four critical points expressed by the users.
Abstract: In this paper, the two-dimension differential transformation method (DTM) is employed to obtain the closed form solutions of the three famous coupled partial differential equation with physical interest namely, the coupled Korteweg-de Vries(KdV) equations, the coupled Burgers equations and coupled nonlinear Schrödinger equation. We begin by showing that how the differential transformation method applies to a linear and non-linear part of any PDEs and apply on these coupled PDEs to illustrate the sufficiency of the method for this kind of nonlinear differential equations. The results obtained are in good agreement with the exact solution. These results show that the technique introduced here is accurate and easy to apply.
Abstract: Texture classification is an important image processing
task with a broad application range. Many different techniques for
texture classification have been explored. Using sparse approximation
as a feature extraction method for texture classification is a relatively
new approach, and Skretting et al. recently presented the Frame
Texture Classification Method (FTCM), showing very good results on
classical texture images. As an extension of that work the FTCM is
here tested on a real world application as detection of abnormalities
in mammograms. Some extensions to the original FTCM that are
useful in some applications are implemented; two different smoothing
techniques and a vector augmentation technique. Both detection of
microcalcifications (as a primary detection technique and as a last
stage of a detection scheme), and soft tissue lesions in mammograms
are explored. All the results are interesting, and especially the results
using FTCM on regions of interest as the last stage in a detection
scheme for microcalcifications are promising.
Abstract: Buyer coalition with a combination of items is a group of buyers joining together to purchase a combination of items with a larger discount. The primary aim of existing buyer coalition with a combination of items research is to generate a large total discount. However, the aim is hard to achieve because this research is based on the assumption that each buyer completely knows other buyers- information or at least one buyer knows other buyers- information in a coalition by exchange of information. These assumption contrast with the real world environment where buyers join a coalition with incomplete information, i.e., they concerned only with their expected discounts. Therefore, this paper proposes a new buyer community coalition formation with a combination of items scheme, called the Community Compromised Combinatorial Coalition scheme, under such an environment of incomplete information. In order to generate a larger total discount, after buyers who want to join a coalition propose their minimum required saving, a coalition structure that gives a maximum total retail prices is formed. Then, the total discount division of the coalition is divided among buyers in the coalition depending on their minimum required saving and is a Pareto optimal. In mathematical analysis, we compare concepts of this scheme with concepts of the existing buyer coalition scheme. Our mathematical analysis results show that the total discount of the coalition in this scheme is larger than that in the existing buyer coalition scheme.
Abstract: Inconel 718, a nickel based super-alloy is an
extensively used alloy, accounting for about 50% by weight of
materials used in an aerospace engine, mainly in the gas turbine
compartment. This is owing to their outstanding strength and
oxidation resistance at elevated temperatures in excess of 5500 C.
Machining is a requisite operation in the aircraft industries for the
manufacture of the components especially for gas turbines. This
paper is concerned with optimization of the surface roughness when
turning Inconel 718 with cermet inserts. Optimization of turning
operation is very useful to reduce cost and time for machining. The
approach is based on Response Surface Method (RSM). In this work,
second-order quadratic models are developed for surface roughness,
considering the cutting speed, feed rate and depth of cut as the cutting
parameters, using central composite design. The developed models
are used to determine the optimum machining parameters. These
optimized machining parameters are validated experimentally, and it
is observed that the response values are in reasonable agreement with
the predicted values.
Abstract: The modern queueing theory is one of the powerful
tools for a quantitative and qualitative analysis of communication systems, computer networks, transportation systems, and many other technical systems. The paper is designated to the analysis of queueing
systems, arising in the networks theory and communications theory
(called open queueing network). The authors of this research in the
sphere of queueing theory present the theorem about the law of the iterated logarithm (LIL) for the queue length of a customers in open
queueing network and its application to the mathematical model of
the open message switching system.
Abstract: The main objective developed in this paper is to find a
graphic technique for modeling, simulation and diagnosis of the
industrial systems. This importance is much apparent when it is about
a complex system such as the nuclear reactor with pressurized water
of several form with various several non-linearity and time scales. In
this case the analytical approach is heavy and does not give a fast
idea on the evolution of the system. The tool Bond Graph enabled us
to transform the analytical model into graphic model and the
software of simulation SYMBOLS 2000 specific to the Bond Graphs
made it possible to validate and have the results given by the
technical specifications. We introduce the analysis of the problem
involved in the faults localization and identification in the complex
industrial processes. We propose a method of fault detection applied
to the diagnosis and to determine the gravity of a detected fault. We
show the possibilities of application of the new diagnosis approaches
to the complex system control. The industrial systems became
increasingly complex with the faults diagnosis procedures in the
physical systems prove to become very complex as soon as the
systems considered are not elementary any more. Indeed, in front of
this complexity, we chose to make recourse to Fault Detection and
Isolation method (FDI) by the analysis of the problem of its control
and to conceive a reliable system of diagnosis making it possible to
apprehend the complex dynamic systems spatially distributed applied
to the standard pressurized water nuclear reactor.