Abstract: Most of the commercial gluten free products are
nutritionally inferior when compared to gluten containing
counterparts as manufacturers most often use the refined flours and
starches. So it is possible that people on gluten free diet have low
intake of fibre content. The foxtail millet flour and copra meal are
gluten free and have high fibre and protein contents. The formulation
of fibre rich gluten free cookies was optimized by response surface
methodology considering independent process variables as proportion
of Foxtail millet (Setaria italica) flour in mixed flour, fat content and
guar gum. The sugar, sodium chloride, sodium bicarbonates and
water were added in fixed proportion as 60, 1.0, 0.4 and 20% of
mixed flour weight, respectively. Optimum formulation obtained for
maximum spread ratio, fibre content, surface L-value, overall
acceptability and minimum breaking strength were 80% foxtail millet
flour in mixed flour, 42.8 % fat content and 0.05% guar gum.
Abstract: Series compensators have been used for many years,
to increase the stability and load ability of transmission line. They
compensate retarded or advanced volt drop of transmission lines
by placing advanced or retarded voltage in series with them to
compensate the effective reactance, which cause to increase load
ability of transmission lines. In this paper, two method of fuzzy
controller, based on power reference tracking and impedance
reference tracking have been developed on TCSC controller in
order to increase load ability and improving power oscillation
damping of system. In these methods, fire angle of thyristors are
determined directly through the special Rule-bases with the error
and change of error as the inputs. The simulation results of two
area four- machines power system show the good performance of
power oscillation damping in system. Comparison of this method
with classical PI controller shows the increasing speed of system
response in power oscillation damping.
Abstract: Component handling system is one of the important sub systems of Prototype Fast Breeder Reactor (PFBR) used for fuel handling. Core handling system is again a sub system of component handling system. Core handling system consists of in-vessel and ex-vessel subassembly handling. In-vessel core handling involves transfer arm, large rotatable plug and small rotatable plug operations. Modeling and simulation of in-vessel core handling is a part of development of Prototype Fast Breeder Reactor Operator Training Simulator. This paper deals with simulation and modeling of operations of transfer arm, large rotatable plug and small rotatable plug needed for in-vessel core handling. Process modeling was developed in house using platform independent Cµ code with OpenGL (Open Graphics Library). The control logic models and virtual panel were modeled using simulation tool.
Abstract: The behavior of Radial Basis Function (RBF) Networks greatly depends on how the center points of the basis functions are selected. In this work we investigate the use of instance reduction techniques, originally developed to reduce the storage requirements of instance based learners, for this purpose. Five Instance-Based Reduction Techniques were used to determine the set of center points, and RBF networks were trained using these sets of centers. The performance of the RBF networks is studied in terms of classification accuracy and training time. The results obtained were compared with two Radial Basis Function Networks: RBF networks that use all instances of the training set as center points (RBF-ALL) and Probabilistic Neural Networks (PNN). The former achieves high classification accuracies and the latter requires smaller training time. Results showed that RBF networks trained using sets of centers located by noise-filtering techniques (ALLKNN and ENN) rather than pure reduction techniques produce the best results in terms of classification accuracy. The results show that these networks require smaller training time than that of RBF-ALL and higher classification accuracy than that of PNN. Thus, using ALLKNN and ENN to select center points gives better combination of classification accuracy and training time. Our experiments also show that using the reduced sets to train the networks is beneficial especially in the presence of noise in the original training sets.
Abstract: The purpose of this paper is to demonstrate the ability
of a genetic programming (GP) algorithm to evolve a team of data
classification models. The GP algorithm used in this work is
“multigene" in nature, i.e. there are multiple tree structures (genes)
that are used to represent team members. Each team member assigns
a data sample to one of a fixed set of output classes. A majority vote,
determined using the mode (highest occurrence) of classes predicted
by the individual genes, is used to determine the final class
prediction. The algorithm is tested on a binary classification problem.
For the case study investigated, compact classification models are
obtained with comparable accuracy to alternative approaches.
Abstract: This paper investigates the development of weld zone
in Resistance Spot Welding (RSW) which focuses on weld nugget and Heat Affected Zone (HAZ). The effects of four factors namely
weld current, weld time, electrode force and hold time were studied using a general 24 factorial design augmented by five centre points. The results of the analysis showed that all selected factors except
hold time exhibit significant effect on weld nugget radius and HAZ size. Optimization of the welding parameters (weld current, weld
time and electrode force) to normalize weld nugget and to minimize
HAZ size was then conducted using Central Composite Design (CCD) in Response Surface Methodology (RSM) and the optimum
parameters were determined. A regression model for radius of weld nugget and HAZ size was developed and its adequacy was evaluated.
The experimental results obtained under optimum operating conditions were then compared with the predicted values and were
found to agree satisfactorily with each other
Abstract: Heat source addition to the axisymmetric supersonic
inlet may improve the performance parameters, which will increase
the inlet efficiency. In this investigation the heat has been added to
the flow field at some distance ahead of an axisymmetric inlet by
adding an imaginary thermal source upstream of cowl lip. The effect
of heat addition on the drag coefficient, mass flow rate and the
overall efficiency of the inlet have been investigated. The results
show that heat addition causes flow separation, hence to prevent this
phenomena, roughness has been added on the spike surface.
However, heat addition reduces the drag coefficient and the inlet
mass flow rate considerably. Furthermore, the effects of position,
size, and shape on the inlet performance were studied. It is found that
the thermal source deflects the flow streamlines. By improper
location of the thermal source, the optimum condition has been
obtained. For the optimum condition, the drag coefficient is
considerably reduced and the inlet mass flow rate and its efficiency
have been increased slightly. The optimum shape of the heat source
is obtained too.
Abstract: A real time distributed computing has
heterogeneously networked computers to solve a single problem. So
coordination of activities among computers is a complex task and
deadlines make more complex. The performances depend on many
factors such as traffic workloads, database system architecture,
underlying processors, disks speeds, etc. Simulation study have been
performed to analyze the performance under different transaction
scheduling: different workloads, arrival rate, priority policies,
altering slack factors and Preemptive Policy. The performance metric
of the experiments is missed percent that is the percentage of
transaction that the system is unable to complete. The throughput of
the system is depends on the arrival rate of transaction. The
performance can be enhanced with altering the slack factor value.
Working on slack value for the transaction can helps to avoid some
of transactions from killing or aborts. Under the Preemptive Policy,
many extra executions of new transactions can be carried out.
Abstract: The non-destructive testing of launch tube weld with
radiography was investigated and evaluated with AWS D1.1
standard. The paper started with preparation of launch tube and
radiographic inspection. X-Ray inspection then was done and gotten
the result. The judgment of inspection results were concluded by
certified person and finally, the evaluation with AWS D1.1 standard
was conducted as well.
The result shown that weld position P1 was not conformed to
AWS D1.1 which allowed size of incomplete penetration did not
exceed 4 mm. The other welds were corresponded to as mentioned
standard. Additionally, the corrective actions for incomplete
penetration either provided for future actions.
Abstract: The aim of the work was to attenuate the vibration amplitude in CESNA 172 airplane wing by using Functionally Graded Material instead of uniform or composite material. Wing strength was achieved by means of stress analysis study, while wing vibration amplitudes and shapes were achieved by means of Modal and Harmonic analysis. Results were verified by applying the methodology in a simple cantilever plate to the simple model and the results were promising and the same methodology can be applied to the airplane wing model. Aluminum models, Titanium models, and functionally graded materials of Aluminum and titanium results were compared to show a great vibration attenuation after using the FGM. Optimization in FGM gradation satisfied our objective of reducing and attenuating the vibration amplitudes to show the effect of using FGM in vibration behavior. Testing the Aluminum rich models, and comparing it with the titanium rich model was an optimization in this paper. Results have shown a significant attenuation in vibration magnitudes when using FGM instead of Titanium Plate, and Aluminium wing with FGM Spurs instead of Aluminium wings. It was also recommended that in future, changing the graphical scale to 1:10 or even 1:1 when the computers- capabilities allow.
Abstract: A phorbol-12-myristate-13-acetate (TPA) is a synthetic analogue of phorbol ester (PE), a natural toxic compound of Euphorbiaceae plant. The oil extracted from plants of this family is useful source for primarily biofuel. However this oil might also be used as a foodstuff due to its significant nutrition content. The limitations for utilizing the oil as a foodstuff are mainly due to a toxicity of PE. Currently, a majority of PE detoxification processes are expensive as include multi steps alcohol extraction sequence.
Ozone is considered as a strong oxidative agent. It reacts with PE by attacking the carbon-carbon double bond of PE. This modification of PE molecular structure yields a non toxic ester with high lipid content.
This report presents data on development of simple and cheap PE detoxification process with water application as a buffer and ozone as reactive component. The core of this new technique is an application for a new microscale plasma unit to ozone production and the technology permits ozone injection to the water-TPA mixture in form of microbubbles.
The efficacy of a heterogeneous process depends on the diffusion coefficient which can be controlled by contact time and interfacial area. The low velocity of rising microbubbles and high surface to volume ratio allow efficient mass transfer to be achieved during the process. Direct injection of ozone is the most efficient way to process with such highly reactive and short lived chemical.
Data on the plasma unit behavior are presented and the influence of gas oscillation technology on the microbubble production mechanism has been discussed. Data on overall process efficacy for TPA degradation is shown.
Abstract: System is using multiple processors for computing and information processing, is increasing rapidly speed operation of these systems compared with single processor systems, very significant impact on system performance is increased .important differences to yield a single multi-processor cpu, the scheduling policies, to reduce the implementation time of all processes. Notwithstanding the famous algorithms such as SPT, LPT, LSPT and RLPT for scheduling and there, but none led to the answer are not optimal.In this paper scheduling using genetic algorithms and innovative way to finish the whole process faster that we do and the result compared with three algorithms we mentioned.
Abstract: The present investigation aimed to study the
histomorphometric characterizations of the thyroid gland of the duck.
Five adult male and five adult female ducks were used in the
experiment. Results showed that the overall histological structure of
the thyroid gland of the duck were similar to those of the other
vertebrae. The gland consisted of roughly spherical randomly
distributed micro and macrofollicles with very little interstitial tissue
between them. Each follicle is lined by a single layer of epithelial
cells enclosing a cavity, the follicular cavity, which is filled with
colloid. Ultrastructural findings showed that the apical surface of the
follicular cells bears a variable number of short, irregularly
distributed microvilli which are apparently more numerous on the
columnar cells than on the lower, relatively inactive cells.
Mitochondria and rough endoplasmic reticulum occupy the
subnuclear region of the follicular cell, whereas the Golgi complex,
free ribosomes and colloid droplets were found in the apical
cytoplasm. At light or electron microscopic levels, there was no sex
difference in histomorphometric characteristics of the thyroid
glands.ls.
Abstract: This paper compares the heuristic Global Search
Techniques; Genetic Algorithm, Particle Swarm Optimization,
Simulated Annealing, Generalized Pattern Search, genetic algorithm
hybridized with Nelder–Mead and Generalized pattern search
technique for tuning of fuzzy PID controller for Puma 560. Since the
actual control is in joint space ,inverse kinematics is used to generate
various joint angles correspoding to desired cartesian space
trajectory. Efficient dynamics and kinematics are modeled on Matlab
which takes very less simulation time. Performances of all the tuning
methods with and without disturbance are compared in terms of ITSE
in joint space and ISE in cartesian space for spiral trajectory tracking.
Genetic Algorithm hybridized with Generalized Pattern Search is
showing best performance.
Abstract: Business rules are widely used within the services
sector. They provide consistency and allow relatively unskilled staff
to process complex transactions correctly. But there are many
examples where the rules themselves have an impact on the costs and
profits of an organisation. Financial services, transport and human
services are areas where the rules themselves can impact the bottom
line in a predictable way. If this is the case, how can we find that set
of rules that maximise profit, performance or customer service, or
any other key performance indicators? The manufacturing, energy
and process industries have embraced mathematical optimisation
techniques to improve efficiency, increase production and so on. This
paper explores several real world (but simplified) problems in the
services sector and shows how business rules can be optimised. It
also examines the similarities and differences between the service
and other sectors, and how optimisation techniques could be used to
deliver similar benefits.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: By taking advantage of computer-s processing power, an unlimited number of variations and parameters in both spatial and environmental can be provided while following the same set of rules and constraints. This paper focuses on using the tools of parametric urbanism towards a more responsive environmental and sustainable urban morphology. It presents an understanding to Parametric Urban Comfort Envelope (PUCE) as an interactive computational assessment urban model. In addition, it investigates the applicability potentials of this model to generate an optimized urban form to Borg El Arab city (a new Egyptian Community) concerning the human comfort values specially wind and solar envelopes. Finally, this paper utilizes its application outcomes -both visual and numerical- to extend the designer-s limitations by decrease the concern of controlling and manipulation of geometry, and increase the designer-s awareness about the various potentials of using the parametric tools to create relationships that generate multiple geometric alternatives.
Abstract: The intermittent connectivity modifies the “always
on" network assumption made by all the distributed query processing
systems. In modern- day systems, the absence of network
connectivity is considered as a fault. Since the last upload, it might
not be feasible to transmit all the data accumulated right away over
the available connection. It is possible that vital information may be
delayed excessively when the less important information takes place
of the vital information. Owing to the restricted and uneven
bandwidth, it is vital that the mobile nodes make the most
advantageous use of the connectivity when it arrives. Hence, in order
to select the data that needs to be transmitted first, some sort of data
prioritization is essential. A continuous query processing system for
intermittently connected mobile networks that comprises of a delaytolerant
continuous query processor distributed across the mobile
hosts has been proposed in this paper. In addition, a mechanism for
prioritizing query results has been designed that guarantees enhanced
accuracy and reduced delay. It is illustrated that our architecture
reduces the client power consumption, increases query efficiency by
the extensive simulation results.
Abstract: The study will search the level of existence of the
sweethearting in Saudi Arabia's Supermarkets in Riyadh.
Sweethearting occurs when frontline workers give unauthorized free
or uncounted goods and services to customer-s conspirators. The
store managers and /or security managers were asked about the
sweethearting that occurs in the supermarkets. The characteristics of
sweethearting in Riyadh stores were investigated. Two independent
variables were related to the report of sweethearting. These
independent variables are: The effect of store environment on
sweethearting and the security techniques and loss prevention
electronics techniques used. This study expected to shed the light
about the level of sweethearting in Saudi Arabia and the factors
behind it. This study will serve as an exploratory study for such
phenomenon in Saudi Arabia as well as both descriptive for the
characteristics of sweethearting and explanatory study to link
between the environmental and security systems factors to
sweethearting.
Abstract: An optimal solution for a large number of constraint
satisfaction problems can be found using the technique of
substitution and elimination of variables analogous to the technique
that is used to solve systems of equations. A decision function
f(A)=max(A2) is used to determine which variables to eliminate. The
algorithm can be expressed in six lines and is remarkable in both its
simplicity and its ability to find an optimal solution. However it is
inefficient in that it needs to square the updated A matrix after each
variable elimination. To overcome this inefficiency the algorithm is
analyzed and it is shown that the A matrix only needs to be squared
once at the first step of the algorithm and then incrementally updated
for subsequent steps, resulting in significant improvement and an
algorithm complexity of O(n3).