Abstract: The thermal behavior of a large-scale, phase change material (PCM) enhanced building envelope system was studied in regard to the need for pre-fabricated construction in subtropical regions. The proposed large-scale envelope consists of a reinforced aluminum skin, insulation core, phase change material and reinforced gypsum board. The PCM impact on an energy efficiency of an enveloped room was resolved by validation of the EnergyPlus numerical scheme and optimization of a smart material location in the core. The PCM location was optimized by a minimization method of a cooling energy demand. It has been shown that there is good agreement between the test and simulation results. The optimal location of the PCM layer in Hong Kong summer conditions has been then recomputed for core thicknesses of 40, 60 and 80 mm. A non-dimensional value of the optimal PCM location was obtained to be same for all the studied cases and the considered external and internal conditions.
Abstract: Meeting the growth in demand for digital services
such as social media, telecommunications, and business and cloud
services requires large scale data centres, which has led to an increase
in their end use energy demand. Generally, over 30% of data centre
power is consumed by the necessary cooling overhead. Thus energy
can be reduced by improving the cooling efficiency. Air and liquid
can both be used as cooling media for the data centre. Traditional
data centre cooling systems use air, however liquid is recognised as a
promising method that can handle the more densely packed data
centres. Liquid cooling can be classified into three methods; rack heat
exchanger, on-chip heat exchanger and full immersion of the
microelectronics. This study quantifies the improvements of heat
transfer specifically for the case of immersed microelectronics by
varying the CPU and heat sink location. Immersion of the server is
achieved by filling the gap between the microelectronics and a water
jacket with a dielectric liquid which convects the heat from the CPU
to the water jacket on the opposite side. Heat transfer is governed by
two physical mechanisms, which is natural convection for the fixed
enclosure filled with dielectric liquid and forced convection for the
water that is pumped through the water jacket. The model in this
study is validated with published numerical and experimental work
and shows good agreement with previous work. The results show that
the heat transfer performance and Nusselt number (Nu) is improved
by 89% by placing the CPU and heat sink on the bottom of the
microelectronics enclosure.
Abstract: A well designed and executed Production Planning
and Control (PPC) system is one of the key levers for superior
performance in the current manufacturing set-up. Hence, measuring
the PPC system performance has become a necessity for long term
success. The present study examined PPC related issues which
impact the production capacity and productivity of leather companies
with special focus on Kombolcha Tannery Share Company (KTSC),
Ethiopia. Physical observation, interview, and questionnaire were
used to generate necessary information from the respondents and
reach valid conclusions. Company annual reports were referred and
analyzed to triangulate primary data. Consequently, the study
revealed that KTSC runs below its capacity due to its inefficient PPC
system being in use for which the root causes were identified. The
study thereby conceptualizes a PPC system improvement framework
comprising three pillars viz., management culture, internal capability
and performance measurement together with key considerations in
each case. The study findings enable the company to recognize the
importance of efficient PPC system as a source of competitive
advantage. It also aid managers in evaluating various PPC execution
schemes to enhance productivity.
Abstract: The characteristics of temperature distribution and
electric field in a natural rubber glove (NRG) using microwave
energy during microwave heating process are investigated
numerically and experimentally. A three-dimensional model of NRG
and microwave oven are considered in this work. The influences of
position, heating time and rotation angle of NRG on temperature
distribution and electric field are presented in details. The coupled
equations of electromagnetic wave propagation and heat transfer are
solved using the finite element method (FEM). The numerical model
is validated with an experimental study at a frequency of 2.45 GHz.
The results show that the numerical results closely match the
experimental results. Furthermore, it is found that the temperature
distribution and electric field increases with increasing heating time.
The hot spot zone appears in NRG at the tip of middle finger while
the maximum temperature occurs in case of rotation angle of NRG =
60 degree. This investigation provides the essential aspects for a
fundamental understanding of heat transport of NRG using
microwave energy in industry.
Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: Content Based Image Retrieval (CBIR) coupled with
Case Based Reasoning (CBR) is a paradigm that is becoming
increasingly popular in the diagnosis and therapy planning of medical
ailments utilizing the digital content of medical images. This paper
presents a survey of some of the promising approaches used in the
detection of abnormalities in retina images as well in
mammographic screening and detection of regions of interest
in MRI scans of the brain. We also describe our proposed
algorithm to detect hard exudates in fundus images of the
retina of Diabetic Retinopathy patients.
Abstract: Part and parcel of building green homes (GHs) with
favorable thermal comfort (TC) is to design and build with reduced
carbon footprint (CF) from embodied energy in the building envelope
and reduced operational CF overall. Together, the environmental
impact of GHs can be reduced significantly. Nevertheless, there is
still a need to identify the base CF value for Malaysian GHs and this
can be done by assessing existing ones which can then be compared
to conventional and vernacular houses which are built differently
with different building materials. This paper underlines the research
design and introduces the case studies. For now, the operational CF
of the case studies is beyond the scope of this study. Findings from
this research could identify the best building material and
construction technique combination to build GHs depending on the
available skills, financial constraints and the condition of the
immediate environment.
Abstract: The present work analyses different parameters of end
milling to minimize the surface roughness for AISI D2 steel. D2 Steel
is generally used for stamping or forming dies, punches, forming
rolls, knives, slitters, shear blades, tools, scrap choppers, tyre
shredders etc. Surface roughness is one of the main indices that
determines the quality of machined products and is influenced by
various cutting parameters. In machining operations, achieving
desired surface quality by optimization of machining parameters, is a
challenging job. In case of mating components the surface roughness
become more essential and is influenced by the cutting parameters,
because, these quality structures are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of
process parameters or their interactive effects (i.e. on process
environment). In this work, the effects of selected process parameters
on surface roughness and subsequent setting of parameters with the
levels have been accomplished by Taguchi’s parameter design
approach. The experiments have been performed as per the
combination of levels of different process parameters suggested by
L9 orthogonal array. Experimental investigation of the end milling of
AISI D2 steel with carbide tool by varying feed, speed and depth of
cut and the surface roughness has been measured using surface
roughness tester. Analyses of variance have been performed for mean
and signal-to-noise ratio to estimate the contribution of the different
process parameters on the process.
Abstract: Flow blockages referring to the increase in flow are
being considered as a vital equipment for marine current energy
conversion. However, the shape of these devices will result in
extracted energy under the operation. The present work investigates
the effect of two configurations of a grating, convergent and
divergent that located upstream, to the water flow velocity. The flow
characteristics are studied by Computational Fluid Dynamic
simulation by using the ANSYS Fluent solver for these specified
arrangements of the grating. The results indicate that distinguished
characteristics of flow velocity between “convergent” and
“divergent” grating placements is up to 10% in confined conditions.
Furthermore, the velocity in case of convergent grating is higher
than that of divergent grating.
Abstract: The aim of this paper is to select the most accurate
forecasting method for predicting the future values of the
unemployment rate in selected European countries. In order to do so,
several forecasting techniques adequate for forecasting time series
with trend component, were selected, namely: double exponential
smoothing (also known as Holt`s method) and Holt-Winters` method
which accounts for trend and seasonality. The results of the empirical
analysis showed that the optimal model for forecasting
unemployment rate in Greece was Holt-Winters` additive method. In
the case of Spain, according to MAPE, the optimal model was double
exponential smoothing model. Furthermore, for Croatia and Italy the
best forecasting model for unemployment rate was Holt-Winters`
multiplicative model, whereas in the case of Portugal the best model
to forecast unemployment rate was Double exponential smoothing
model. Our findings are in line with European Commission
unemployment rate estimates.
Abstract: With drug resistance becoming widespread in
Plasmodium falciparum infections, the development of the alternative
drugs is the desired strategy for prevention and cure of malaria. Three
drug targets were selected to screen promising drug molecules from
the GSK library of 13469 molecules. Using an in silico structure-based
drug designing approach, the differences in binding energies of
the substrate and inhibitor were exploited between target sites of
parasite and human to design a drug molecule against Plasmodium.
The docking studies have shown several promising molecules from
GSK library with more effective binding as compared to the already
known inhibitors for the drug targets. Though stronger interaction has
been shown by several molecules as compared to the reference, few
molecules have shown the potential as drug candidates though in
vitro studies are required to validate the results. In case of
thymidylate synthase-dihydrofolatereductase (TS-DHFR), three
compounds have shown promise for future studies as potential drugs.
Abstract: The impact of Special Economic Zones (SEZs) has
been analyzed for many years by researchers. There are lot of
theoretical studies proving the SEZs importance for regional
development, however, there is lack of empirical studies (and they
are mainly focused on China market) that are based on available data.
The theoretical studies indicate the various impacts of enterprises
operating within SEZs on the economy. The article proves that, in
case of Poland, locating SEZs in municipalities is an important part
of increasing municipalities’ income. Therefore SEZs have a positive
impact on regional development. Municipality income is understood
as taxes paid by taxpayers who depend on SEZ companies’
performance. The analysis includes the Corporate Income Tax (CIT),
Personal Income Tax (PIT) and real estate tax. The effects of SEZs
on regional development were narrowed to a few variables that are
most significant for the financial system. The analysis indicates the
significant impact of SEZs on the amount of taxes influencing the
municipality budget.
Abstract: Future mobile networks following 5th generation will
be characterized by one thousand times higher gains in capacity;
connections for at least one hundred billion devices; user experience
capable of extremely low latency and response times. To be close to
the capacity requirements and higher reliability, advanced
technologies have been studied, such as multiple connectivity, small
cell enhancement, heterogeneous networking, and advanced
interference and mobility management. This paper is focused on the
multiple connectivity in heterogeneous cellular networks. We
investigate the performance of coverage and user throughput in several
deployment scenarios. Using the stochastic geometry approach, the
SINR distributions and the coverage probabilities are derived in case
of dual connection. Also, to compare the user throughput enhancement
among the deployment scenarios, we calculate the spectral efficiency
and discuss our results.
Abstract: Learning Management System (LMS) is the system
which uses to manage the learning in order to grouping the content
and learning activity between the lecturer and learner including
online examination and evaluation. Nowadays, it is the borderless
learning era so the learning activities can be accessed from
everywhere in the world and also anytime via the information
technology and media. The learner can easily access to the
knowledge so the different in time and distance is not a constraint for
learning anymore.
The learning pattern which was used in this research is the
integration of the in-class learning and online learning via internet
and will be able to monitor the progress by the Learning management
system which will create the fast response and accessible learning
process via the social media. In order to increase the capability and
freedom of the learner, the system can show the current and history
of the learning document, video conference and also has the chat
room for the learner and lecturer to interact to each other.
So the objectives of the “The Design and Applied of Learning
Management System via Social Media on Internet: Case Study of
Operating System for Business Subject” are to expand the
opportunity of learning and to increase the efficiency of learning as
well as increase the communication channel between lecturer and
student. The data of this research was collect from 30 users of the
system which are students who enroll in the subject. And the result of
the research is in the “Very Good” which is conformed to the
hypothesis.
Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: The goal of this study is to identify success factors
that could influence the ISMS self-implementation in government
sector from qualitative perspective. This study is based on a case
study in one of the Malaysian government agency. Semi-structured
interviews involving five key informants were conducted to examine
factors addressed in the conceptual framework. Subsequently,
thematic analysis was executed to describe the influence of each
factor on the success implementation of ISMS. The result of this
study indicates that management commitment, implementer
commitment and implementer competency are part of the success
factors for ISMS self-implementation in Malaysian Government
Sector.
Abstract: The seismic responses of steel buildings with semirigid
post-tensioned connections (PC) are estimated and compared
with those of steel buildings with typical rigid (welded) connections
(RC). The comparison is made in terms of global and local response
parameters. The results indicate that the seismic responses in terms of
interstory shears, roof displacements, axial load and bending
moments are smaller for the buildings with PC connection. The
difference is larger for global than for local parameters, which in turn
varies from one column location to another. The reason for this
improved behavior is that the buildings with PC dissipate more
hysteretic energy than those with RC. In addition, unlike the case of
buildings with WC, for the PC structures the hysteretic energy is
mostly dissipated at the connections, which implies that structural
damage in beams and columns is not significant. According to these
results, steel buildings with PC are a viable option in high seismicity
areas because of their smaller response and self-centering connection
capacity as well as the fact that brittle failure is avoided.
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: This study aims to investigate the possibility of crime
prevention through CCTV by analyzing the appropriateness of the
CCTV location, whether it is installed in the hotspot of crime-prone
areas, and exploring the crime prevention effect and transition effect.
The real crime and CCTV locations of case city were converted into
the spatial data by using GIS. The data was analyzed by hotspot
analysis and weighted displacement quotient (WDQ). As study
methods, it analyzed existing relevant studies for identifying the trends
of CCTV and crime studies based on big data from 1800 to 2014 and
understanding the relation between CCTV and crime. Second, it
investigated the current situation of nationwide CCTVs and analyzed
the guidelines of CCTV installation and operation to draw attention to
the problems and indicating points of CCTV use. Third, it investigated
the crime occurrence in case areas and the current situation of CCTV
installation in the spatial aspects, and analyzed the appropriateness and
effectiveness of CCTV installation to suggest a rational installation of
CCTV and the strategic direction of crime prevention. The results
demonstrate that there was no significant effect in the installation of
CCTV on crime prevention in the case area. This indicates that CCTV
should be installed and managed in a more scientific way reflecting
local crime situations. In terms of CCTV, the methods of spatial
analysis such as GIS, which can evaluate the installation effect, and the
methods of economic analysis like cost-benefit analysis should be
developed. In addition, these methods should be distributed to local
governments across the nation for the appropriate installation of
CCTV and operation. This study intended to find a design guideline of
the optimum CCTV installation. In this regard, this study is
meaningful in that it will contribute to the creation of a safe city.