Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: Although it is not intended to identify distance
education students as a homogeneous group, recent research has
demonstrated that there are some demographic and personality
common traits among most of them that provide the basis for the
description of a typical distance learning student. The purpose of this
paper is to describe these common traits and to facilitate their
learning journey within a distance education program. The described
research is an initiative of the Distance Education Unit at the
European University Cyprus (Laureate International Universities) in
the context of its action for the improvement of the students’
performance.
Abstract: We present a solution to the Maxmin u/E parameters
estimation problem of possibility distributions in m-dimensional
case. Our method is based on geometrical approach, where minimal
area enclosing ellipsoid is constructed around the sample. Also we
demonstrate that one can improve results of well-known algorithms
in fuzzy model identification task using Maxmin u/E parameters
estimation.
Abstract: Cloud computing (CC) has already gained overall
appreciation in research and practice. Whereas the willingness to
integrate cloud services in various IT environments is still unbroken,
the previous CC procurement processes run mostly in an unorganized
and non-standardized way. In practice, a sufficiently specific, yet
applicable business process for the important acquisition phase is
often lacking. And research does not appropriately remedy this
deficiency yet. Therefore, this paper introduces a field-tested
approach for CC procurement. Based on an extensive literature
review and augmented by expert interviews, we designed a model
that is validated and further refined through an in-depth real-life case
study. For the detailed process description, we apply the event-driven
process chain notation (EPC). The gained valuable insights into the
case study may help CC research to shift to a more socio-technical
area. For practice, next to giving useful organizational instructions
we will provide extended checklists and lessons learned.
Abstract: Food as perishable goods represents a specific and
sensitive part in the supply chain theory, since changing physical or
chemical characteristics considerably influence the approach to stock
management. The most delicate phase of this process is
transportation, where it becomes difficult to ensure the stable
conditions which limit deterioration, since the value of the
deterioration rate could be easily influenced by the mode of
transportation. The fuzzy definition of variables allows one to take
these variations into account. Furthermore, an appropriate choice of
the defuzzification method permits one to adapt results to real
conditions as far as possible. In this article those methods which take
into account the relationship between the deterioration rate of
perishable goods and transportation by ship will be applied with the
aim of (a) minimizing the total cost function, defined as the sum of
the ordering cost, holding cost, disposing cost and transportation
costs, and (b) improving the supply chain sustainability by reducing
environmental impact and waste disposal costs.
Abstract: Validity, integrity, and impacts of the IT systems of
the US federal courts have been studied as part of the Human Rights
Alert-NGO (HRA) submission for the 2015 Universal Periodic
Review (UPR) of human rights in the United States by the Human
Rights Council (HRC) of the United Nations (UN). The current
report includes overview of IT system analysis, data-mining and case
studies. System analysis and data-mining show: Development and
implementation with no lawful authority, servers of unverified
identity, invalidity in implementation of electronic signatures,
authentication instruments and procedures, authorities and
permissions; discrimination in access against the public and
unrepresented (pro se) parties and in favor of attorneys; widespread
publication of invalid judicial records and dockets, leading to their
false representation and false enforcement. A series of case studies
documents the impacts on individuals' human rights, on banking
regulation, and on international matters. Significance is discussed in
the context of various media and expert reports, which opine
unprecedented corruption of the US justice system today, and which
question, whether the US Constitution was in fact suspended. Similar
findings were previously reported in IT systems of the State of
California and the State of Israel, which were incorporated, subject to
professional HRC staff review, into the UN UPR reports (2010 and
2013). Solutions are proposed, based on the principles of publicity of
the law and the separation of power: Reliance on US IT and legal
experts under accountability to the legislative branch, enhancing
transparency, ongoing vigilance by human rights and internet
activists. IT experts should assume more prominent civic duties in the
safeguard of civil society in our era.
Abstract: The Roma (Gypsies) is a transnational minority with a
high degree of consanguineous marriages. Similar to other
genetically isolated founder populations, the Roma harbor a number
of unique or rare genetic disorders. This paper discusses about a rare
form of Charcot-Marie-Tooth disease – type 4G (CMT4G), also
called Hereditary Motor and Sensory Neuropathy type Russe, an
autosomal recessive disease caused by mutation private to Roma
characterized by abnormally increased density of non-myelinated
axons. CMT4G was originally found in Bulgarian Roma and in 2009
two putative causative mutations in the HK1 gene were identified.
Since then, several cases were reported in Roma families mainly
from Bulgaria and Spain. Here we present a Slovak Roma family in
which CMT4G was diagnosed on the basis of clinical examination
and genetic testing. This case is a further proof of the role of the HK1
gene in pathogenesis of the disease. It confirms that mutation in the
HK1 gene is a common cause of autosomal recessive CMT disease in
Roma and should be considered as a common part of a diagnostic
procedure.
Abstract: This paper presents optimization of makespan for ‘n’
jobs and ‘m’ machines flexible job shop scheduling problem with
sequence dependent setup time using genetic algorithm (GA)
approach. A restart scheme has also been applied to prevent the
premature convergence. Two case studies are taken into
consideration. Results are obtained by considering crossover
probability (pc = 0.85) and mutation probability (pm = 0.15). Five
simulation runs for each case study are taken and minimum value
among them is taken as optimal makespan. Results indicate that
optimal makespan can be achieved with more than one sequence of
jobs in a production order.
Abstract: Due to water shortage, application of saline water for
irrigation is an urgent in agriculture. In this study the effect of
calcium and potassium application as additive in saline root media for
reduce salinity adverse effects was investigated on tomato growth in
a hydroponic system with unequal distribution of salts in the root
media, which was divided in to two equal parts containing full
Johnson nutrient solution and 40 mMNaCl solution, alone or in
combination with KCl (6 mM), CaCl2 (4 mM), K+Ca (3+2 mM) or
half-strength Johnson nutrient solution. The root splits were
exchanged every 7 days. Results showed that addition of calcium,
calcium-potassium and nutrition elements equivalent to half the
concentration of Johnson formula to the saline-half of culture media
minimized the reduction in plant growth caused by NaCl, although
addition of potassium to culture media wasn’t effective. The greatest
concentration of sodium was observed at the shoot of treatments
which had smallest growth. According to the results of this study, in
case of dynamic and non-uniform distribution of salts in the root
media, by addition of additive to the saline solution, it would be
possible to use of saline water with no significant growth reduction.
Abstract: In this study the instability problem of a modified
Taylor-Couette flow between two vertical coaxial cylinders of radius
R1, R2 is considered. The modification is based on the wavy shape of
the inner cylinder surface, where inner cylinders with different
surface amplitude and wavelength are used. The study aims to
discover the effect of the inner surface geometry on the instability
phenomenon that undergoes Taylor-Couette flow. The study reveals
that the transition processes depends strongly on the amplitude and
wavelength of the inner cylinder surface and resulting in flow
instabilities that are strongly different from that encountered in the
case of the classical Taylor-Couette flow.
Abstract: There exists some time lag between the consumption of
inputs and the production of outputs. This time lag effect should be
considered in calculating efficiency of decision making units (DMU).
Recently, a couple of DEA models were developed for considering
time lag effect in efficiency evaluation of research activities. However,
these models can’t discriminate efficient DMUs because of the nature
of basic DEA model in which efficiency scores are limited to ‘1’. This
problem can be resolved a super-efficiency model. However, a super
efficiency model sometimes causes infeasibility problem. This paper
suggests an output oriented super-efficiency model for efficiency
evaluation under the consideration of time lag effect. A case example
using a long term research project is given to compare the suggested
model with the MpO model.
Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: The objective of the present study is to determine
better eye end design of a mono leaf spring used in light motor
vehicle. A conventional 65Si7 spring steel leaf spring model with
standard eye, casted and riveted eye end are considered. The CAD
model of the leaf springs is prepared in CATIA and analyzed using
ANSYS. The standard eye, casted and riveted eye leaf springs are
subjected to similar loading conditions. The CAE analysis of the leaf
spring is performed for various parameters like deflection and Von-
Mises stress. Mass reduction of 62.9% is achieved in case of riveted
eye mono leaf spring as compared to standard eye mono leaf spring
for the same loading conditions.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: Container handling problems at container terminals
are NP-hard problems. This paper presents an approach using
discrete-event simulation modeling to optimize solution for storage
space allocation problem, taking into account all various interrelated
container terminal handling activities. The proposed approach is
applied on a real case study data of container terminal at Alexandria
port. The computational results show the effectiveness of the
proposed model for optimization of storage space allocation in
container terminal where 54% reduction in containers handling time
in port is achieved.
Abstract: The globalization of markets, the need to develop
competitive advantages and core competencies, among other things,
lead organizations to increasingly cross borders to operate in other
countries. The expatriation of professionals who go to work in
another country besides their own becomes increasingly common. In
order to generate data about this issue, research was conducted
concerning the perception of expatriate employees concerning
expatriation success. The research method used was case study
through a qualitative approach. This research was done through
interviews with five India expatriates and five China expatriates,
interview with expatriate department heads and analysis of company
documents. It was found that there are differences between the
organizational perception and perception of expatriates of what
constitutes mission success. The paper also provides suggestions for
further research and suggestions for future expatriates.
Abstract: The focal aspire of e-Government (eGovt) is to offer
citizen-centered service delivery. Accordingly, the citizenry
consumes services from multiple government agencies through
national portal. Thus, eGovt is an enterprise with the primary
business motive of transparent, efficient and effective public services
to its citizenry and its logical structure is the eGovernment Enterprise
Architecture (eGEA). Since eGovt is IT oriented multifaceted
service-centric system, EA doesn’t do much on an automated
enterprise other than the business artifacts. Service-Oriented
Architecture (SOA) manifestation led some governments to pertain
this in their eGovts, but it limits the source of business artifacts. The
concurrent use of EA and SOA in eGovt executes interoperability and
integration and leads to Service-Oriented e-Government Enterprise
(SOeGE). Consequently, agile eGovt system becomes a reality. As an
IT perspective eGovt comprises of centralized public service artifacts
with the existing application logics belong to various departments at
central, state and local level. The eGovt is renovating to SOeGE by
apply the Service-Orientation (SO) principles in the entire system.
This paper explores IT perspective of SOeGE in India which
encompasses the public service models and illustrated with a case
study the Passport service of India.
Abstract: This paper presents observations on the early
supervised internships in Psychology, currently called basic
internships in Brazil, and its importance in professional training. The
work is an experience report and focuses on the Professional training,
illustrated by the reality of a Brazilian institution, used as a case
study. It was developed from the authors' experience as academic
supervisors of this kind of practice throughout this undergraduate
course, combined with aspects investigated in the post-doctoral
research of one of them. Theoretical references on the subject and
related national legislation are analyzed, as well as reports of students
who experienced at least one semester of this type of practice,
articulated to the observations of the authors. The results demonstrate
the importance of the early supervised internships as a way of
creating opportunities for the students of a first contact with the
professional reality and the practice of psychologists in different
fields of insertion, preparing them for further experiments that require
more involvement in activities of training and practices in
Psychology.