Abstract: In this paper, the C1-conforming finite element method is analyzed for a class of nonlinear fourth-order hyperbolic partial differential equation. Some a priori bounds are derived using Lyapunov functional, and existence, uniqueness and regularity for the weak solutions are proved. Optimal error estimates are derived for both semidiscrete and fully discrete schemes.
Abstract: Urban non-point source (NPS) pollution for a
residential catchment in Miri, Sarawak was investigated for two storm events in 2011. Runoff from two storm events were sampled and tested for water quality parameters including TSS, BOD5, COD,
NH3-N, NO3-N, NO2-N, P and Pb. Concentration of the water quality
parameters was found to vary significantly between storms and the pollutant of concern was found to be NO3-N, TSS, COD and Pb. Results were compared to the Interim National Water Quality
Standards for Malaysia (INWQS),and the stormwater runoff from the
study can be classified as polluted, exceeding class III water quality,
especially in terms of TSS, COD, and NH3-N with maximum EMCs
of 158, 135, and 2.17 mg/L, respectively.
Abstract: Wireless mobile communications have experienced
the phenomenal growth through last decades. The advances in
wireless mobile technologies have brought about a demand for high
quality multimedia applications and services. For such applications
and services to work, signaling protocol is required for establishing,
maintaining and tearing down multimedia sessions. The Session
Initiation Protocol (SIP) is an application layer signaling protocols,
based on request/response transaction model. This paper considers
SIP INVITE transaction over an unreliable medium, since it has been
recently modified in Request for Comments (RFC) 6026. In order to
help in assuring that the functional correctness of this modification is
achieved, the SIP INVITE transaction is modeled and analyzed using
Colored Petri Nets (CPNs). Based on the model analysis, it is
concluded that the SIP INVITE transaction is free of livelocks and
dead codes, and in the same time it has both desirable and
undesirable deadlocks. Therefore, SIP INVITE transaction should be
subjected for additional updates in order to eliminate undesirable
deadlocks. In order to reduce the cost of implementation and
maintenance of SIP, additional remodeling of the SIP INVITE
transaction is recommended.
Abstract: The model-based approach to user interface design relies on developing separate models that are capturing various aspects about users, tasks, application domain, presentation and dialog representations. This paper presents a task modeling approach for user interface design and aims at exploring the mappings between task, domain and presentation models. The basic idea of our approach is to identify typical configurations in task and domain models and to investigate how they relate each other. A special emphasis is put on application-specific functions and mappings between domain objects and operational task structures. In this respect, we will distinguish between three layers in the task decomposition: a functional layer, a planning layer, and an operational layer.
Abstract: Image-based Rendering(IBR) techniques recently
reached in broad fields which leads to a critical challenge to build up
IBR-Driven visualization platform where meets requirement of high
performance, large bounds of distributed visualization resource
aggregation and concentration, multiple operators deploying and
CSCW design employing. This paper presents an unique IBR-based
visualization dataflow model refer to specific characters of IBR
techniques and then discusses prominent feature of IBR-Driven
distributed collaborative visualization (DCV) system before finally
proposing an novel prototype. The prototype provides a well-defined
three level modules especially work as Central Visualization Server,
Local Proxy Server and Visualization Aid Environment, by which
data and control for collaboration move through them followed the
previous dataflow model. With aid of this triple hierarchy architecture
of that, IBR oriented application construction turns to be easy. The
employed augmented collaboration strategy not only achieve
convenient multiple users synchronous control and stable processing
management, but also is extendable and scalable.
Abstract: Macrobenthos distribution along the coastal waters of
Penang National Park was studid to estimate the effect of different
environmental parameters at three stations, during six sampling
months, from June 2010 to April 2011. The aim of this survey was to
investigate different environment stress over soft bottom polychaete
community along Teluk Ketapang and Pantai Acheh (Penang
National Park) over a year period. Variations in the polychaete
community were evaluated using univariate and multivariate
methods. A total of 604 individuals were examined which was
grouped into 23 families. Family Nereidae was the most abundant
(22.68%), followed by Spionidae (22.02%), Hesionidae (12.58%),
Nephtylidae (9.27%) and Orbiniidae (8.61%). It is noticeable that
good results can only be obtained on the basis of good taxonomic
resolution. The maximum Shannon-Wiener diversity (H'=2.16) was
recorded at distance 200m and 1200m (August 2010) in Teluk
Ketapang and lowest value of diversity was found at distance 1200m
(December 2010) in Teluk Ketapang.
Abstract: A new algorithm called Character-Comparison to Character-Access (CCCA) is developed to test the effect of both: 1) converting character-comparison and number-comparison into character-access and 2) the starting point of checking on the performance of the checking operation in string searching. An experiment is performed using both English text and DNA text with different sizes. The results are compared with five algorithms, namely, Naive, BM, Inf_Suf_Pref, Raita, and Cycle. With the CCCA algorithm, the results suggest that the evaluation criteria of the average number of total comparisons are improved up to 35%. Furthermore, the results suggest that the clock time required by the other algorithms is improved in range from 22.13% to 42.33% by the new CCCA algorithm.
Abstract: In this paper newly reported Cosh window function is
used in the design of prototype filter for M-channel Near Perfect
Reconstruction (NPR) Cosine Modulated Filter Bank (CMFB). Local
search optimization algorithm is used for minimization of distortion
parameters by optimizing the filter coefficients of prototype filter.
Design examples are presented and comparison has been made with
Kaiser window based filterbank design of recently reported work.
The result shows that the proposed design approach provides lower
distortion parameters and improved far-end suppression than the
Kaiser window based design of recent reported work.
Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) is an efficient method of data transmission for high speed
communication systems. However, the main drawback of OFDM
systems is that, it suffers from the problem of high Peak-to-Average
Power Ratio (PAPR) which causes inefficient use of the High Power
Amplifier and could limit transmission efficiency. OFDM consist of
large number of independent subcarriers, as a result of which the
amplitude of such a signal can have high peak values. In this paper,
we propose an effective reduction scheme that combines DCT and
SLM techniques. The scheme is composed of the DCT followed by
the SLM using the Riemann matrix to obtain phase sequences for the
SLM technique. The simulation results show PAPR can be greatly
reduced by applying the proposed scheme. In comparison with
OFDM, while OFDM had high values of PAPR –about 10.4dB our
proposed method achieved about 4.7dB reduction of the PAPR with
low complexities computation. This approach also avoids
randomness in phase sequence selection, which makes it simpler to
decode at the receiver. As an added benefit, the matrices can be
generated at the receiver end to obtain the data signal and hence it is
not required to transmit side information (SI).
Abstract: Fixed-bed slow pyrolysis experiments of rice husk
have been conducted to determine the effect of pyrolysis
temperature, heating rate, particle size and reactor length on the
pyrolysis product yields. Pyrolysis experiments were performed at
pyrolysis temperature between 400 and 600°C with a constant
heating rate of 60°C/min and particle sizes of 0.60-1.18 mm. The
optimum process conditions for maximum liquid yield from the rice
husk pyrolysis in a fixed bed reactor were also identified. The highest
liquid yield was obtained at a pyrolysis temperature of 500°C,
particle size of
1.18-1.80 mm, with a heating rate of 60°C/min in a 300 mm length
reactor. The obtained yield of, liquid, gas and solid were found be in
the range of 22.57-31.78 %, 27.75-42.26 % and 34.17-42.52 % (all
weight basics) respectively at different pyrolysis conditions. The
results indicate that the effects of pyrolysis temperature and particle
size on the pyrolysis yield are more significant than that of heating
rate and reactor length. The functional groups and chemical
compositions present in the liquid obtained at optimum conditions
were identified by Fourier Transform-Infrared (FT-IR) spectroscopy
and Gas Chromatography/ Mass Spectroscopy (GC/MS) analysis
respectively.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.
Abstract: Unlike its conventional counterpart, Islamic principles
forbid Islamic banks to take any interest-related income and thus
makes deposits from depositors as an important source of fund for its
operational and financing. Consequently, the risk of deposit
withdrawal by depositors is an important aspect that should be wellmanaged
in Islamic banking. This paper aims to investigate factors
that influence depositors- withdrawal behavior in Islamic banks,
particularly in Malaysia, using the framework of theory of reasoned
action. A total of 368 respondents from Klang valley are involved in
the analysis. The paper finds that all the constructs variable i.e.
normative beliefs, subjective norms, behavioral beliefs, and attitude
towards behavior are perceived to be distinct by the respondents. In
addition, the structural equation model is able to verify the structural
relationships between subjective norms, attitude towards behavior
and behavioral intention. Subjective norms gives more influence to
depositors- decision on deposit withdrawal compared to attitude
towards behavior.
Abstract: A multi-board run-time reconfigurable (MRTR)
system for evolvable hardware (EHW) is introduced with the aim to
implement on hardware the bidirectional incremental evolution (BIE)
method. The main features of this digital intrinsic EHW solution rely
on the multi-board approach, the variable chromosome length
management and the partial configuration of the reconfigurable
circuit. These three features provide a high scalability to the solution.
The design has been written in VHDL with the concern of not being
platform dependant in order to keep a flexibility factor as high as
possible. This solution helps tackling the problem of evolving
complex task on digital configurable support.
Abstract: An appropriate method for fault identification and classification on extra high voltage transmission line using discrete wavelet transform is proposed in this paper. The sharp variations of the generated short circuit transient signals which are recorded at the sending end of the transmission line are adopted to identify the fault. The threshold values involve fault classification and these are done on the basis of the multiresolution analysis. A comparative study of the performance is also presented for Discrete Fourier Transform (DFT) based Artificial Neural Network (ANN) and Discrete Wavelet Transform (DWT). The results prove that the proposed method is an effective and efficient one in obtaining the accurate result within short duration of time by using Daubechies 4 and 9. Simulation of the power system is done using MATLAB.
Abstract: In This Article We establish moment inequality of
dependent random variables,furthermore some theorems of strong law
of large numbers and complete convergence for sequences of dependent
random variables. In particular, independent and identically
distributed Marcinkiewicz Law of large numbers are generalized to
the case of m0-dependent sequences.
Abstract: Vision-based intelligent vehicle applications often require large amounts of memory to handle video streaming and image processing, which in turn increases complexity of hardware and software. This paper presents an FPGA implement of a vision-based blind spot warning system. Using video frames, the information of the blind spot area turns into one-dimensional information. Analysis of the estimated entropy of image allows the detection of an object in time. This idea has been implemented in the XtremeDSP video starter kit. The blind spot warning system uses only 13% of its logic resources and 95k bits block memory, and its frame rate is over 30 frames per sec (fps).
Abstract: Chess is one of the indoor games, which improves the
level of human confidence, concentration, planning skills and
knowledge. The main objective of this paper is to help the chess
players to improve their chess openings using data mining
techniques. Budding Chess Players usually do practices by analyzing
various existing openings. When they analyze and correlate
thousands of openings it becomes tedious and complex for them. The
work done in this paper is to analyze the best lines of Blackmar-
Diemer Gambit(BDG) which opens with White D4... using data
mining analysis. It is carried out on the collection of winning games
by applying association rules. The first step of this analysis is
assigning variables to each different sequence moves. In the second
step, the sequence association rules were generated to calculate
support and confidence factor which help us to find the best
subsequence chess moves that may lead to winning position.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: The Japanese integrative approach to social systems
can be observed in supply chain management as well as in the
relationship between public and private sectors. Both the Lean
Production System and the Developmental State Model are
characterized by efforts towards the achievement of mutual goals,
resulting in initiatives for capacity building which emphasize the
system level. In Brazil, although organizations undertake efforts to
build capabilities at the individual and organizational levels, the
system level is being neglected. Fieldwork data confirmed the findings
of other studies in terms of the lack of integration in supply chain
management in the Brazilian automobile industry. Moreover, due to
the absence of an active role of the Brazilian state in its relationship
with the private sector, automakers are not fully exploiting the
opportunities in the domestic and regional markets. For promoting a
higher level of economic growth as well as to increase the degree of
spill-over of technologies and techniques, a more integrative approach
is needed.