Abstract: With the growth of modern civilization and
industrialization in worldwide, the demand for energy is increasing
day by day. Majority of the world-s energy needs are met through
fossil fuels and natural gas. As a result the amount of fossil fuels is
on diminishing from year to year. Since the fossil fuel is nonrenewable,
so fuel price is gouging as a consequence of spiraling
demand and diminishing supply. At present the power generation of
our country is mainly depends on imported fossil fuels. To reduce the
dependency on imported fuel, the use of renewable sources has
become more popular. In Bangladesh coconut is widely growing tree.
Especially in the southern part of the country a large area will be
found where coconut tree is considered as natural asset. So, our
endeavor was to use the coconut oil as a renewable and alternative
fuel. This article shows the prospect of coconut oil as a renewable
and alternative fuel of diesel fuel. Since diesel engine has a versatile
uses including small electricity generation, an experimental set up is
then made to study the performance of a small diesel engine using
different blends of bio diesel converted from coconut oil. It is found
that bio diesel has slightly different properties than diesel. With
biodiesel the engine is capable of running without difficulty.
Different blends of bio diesel (i.e. B80, B60, and B 50 etc.) have
been used to avoid complicated modification of the engine or the fuel
supply system. Finally, a comparison of engine performance for
different blends of biodiesel has been carried out to determine the
optimum blend for different operating conditions.
Abstract: In present study, two kinds of thermal power plant ashes; one the fly ash and the other waste ash are mixed with adhesive tragacanth and cement to produce new composite materials. 48 new samples are produced by varying the percentages of the fly ash, waste ash, cement and tragacanth. The new samples are subjected to some tests to find out their properties such as thermal conductivity, compressive strength, tensile strength and sucking capability of water. It is found that; the thermal conductivity decreases with increasing amount of tragacanth in the mixture. The compressive, tensile strength increases when the rate of tragacanth is up to 1%, whilst as the amount of tragacanth increases up to 1.5%, the compressive, tensile strength decreases slightly. The rate of water absorption of samples was more than 30%. From this result, it is concluded that these materials can not be used as external plaster or internal plaster material that faces to water. They can be used in internal plaster unless touching water and they can be used as cover plaster under roof and riprap material in sandwich panels. It is also found that, these materials can be cut with saw, drilled with screw and painted with any kind of paint.
Abstract: When choosing marketing strategies for international markets, one of the factors that should be considered is the cultural differences that exist among consumers in different countries. If the branding strategy has to be contextual and in tune with the culture, then the brand positioning variables has to interact, adapt and respond to the cultural variables in which the brand is operating. This study provides an overview of the relevance of culture in the development of an effective branding strategy in the international business environment. Hence, the main objective of this study is to provide a managerial framework for developing strategies for cross cultural brand management. The framework is useful because it incorporates the variables that are important in the competitiveness of fast food enterprises irrespective of their size. It provides practical, proactive and result oriented analysis that will help fast food firms augment their strategies in the international fast food markets. The proposed framework will enable managers understand the intricacies involved in branding in the global fast food industry and decrease the use of 'trial and error' when entering into unfamiliar markets.
Abstract: An analysis is made of the flow of an incompressible viscoelastic fluid (of small memory) over a porous plate subject to suction or blowing. It is found that velocity at a point increases with increase in the elasticity in the fluid. It is also shown that wall shear stress depends only on suction and is also independent of the material of fluids. No steady solution for velocity distribution exists when there is blowing at the plate. Temperature distribution in the boundary layer is determined and it is found that temperature at a point decreases with increase in the elasticity in the fluid.
Abstract: The present work deals with the stabilisation of
organic clay using hydrated lime. Artificial organic clays were
prepared by adding kaolin and different humic acid contents. Results
given by physical testing show that the presence of humic acid has a
drawback effect on the untreated organic clay. The decrease in
specific gravity value was accompanied by a decrease in dry density
and plasticity of clay at higher humic acid contents. Significant
increase in shear strength at 7 days of curing period is observed in the
lime-treated samples up to 5% lime content. However shear strength
of lime-treated organic clay decreases at longer curing periods. The
results given by laboratory testing is further verified by
microstructure analysis. Based on the results obtained in this study, it
can be concluded that the presence of more than 1.5% humic acid
reduces significantly the efficiency of lime stabilization in organic
clays.
Abstract: A Vehicle-s door wireing harness arrangement structure is provided. In vehicle-s door wiring harness(W/H) system is more toward to arrange a passenger compartment than a hinge and a weatherstrip. This article gives some insight into the dimensioning process, with special focus on large deflection analysis of wiring harness(W/H) in vehicle-s door structures for durability problem. An Finite elements analysis for door wiring harness(W/H) are used for residual stresses and dimensional stability with bending flexible. Durability test data for slim test specimens were compared with the numerical predicted fatigue life for verification. The final lifing of the component combines the effects of these microstructural features with the complex stress state arising from the combined service loading and residual stresses.
Abstract: The radiative exchange method is introduced as a
numerical method for the simulation of radiative heat transfer in an
absorbing, emitting and isotropically scattering media. In this
method, the integro-differential radiative balance equation is solved
by using a new introduced concept for the exchange factor. Even
though the radiative source term is calculated in a mesh structure that
is coarser than the structure used in computational fluid dynamics,
calculating the exchange factor between different coarse elements by
using differential integration elements makes the result of the method
close to that of integro-differential radiative equation. A set of
equations for calculating exchange factors in two and threedimensional
Cartesian coordinate system is presented, and the
method is used in the simulation of radiative heat transfer in twodimensional
rectangular case and a three-dimensional simple cube.
The result of using this method in simulating different cases is
verified by comparing them with those of using other numerical
radiative models.
Abstract: Biometrics methods include recognition techniques
such as fingerprint, iris, hand geometry, voice, face, ears and gait. The gait recognition approach has some advantages, for example it
does not need the prior concern of the observed subject and it can
record many biometric features in order to make deeper analysis, but
most of the research proposals use high computational cost. This
paper shows a gait recognition system with feature subtraction on a
bundle rectangle drawn over the observed person. Statistical results
within a database of 500 videos are shown.
Abstract: The intermittent nature of solar energy and the energy
requirements of buildings necessitate the storage of thermal energy.
In this paper a hybrid system of storing solar energy has been
analyzed. Adding a LHS medium to a commercial solar water heater,
the required energy for heating a small room was obtained in
addition to preparing hot water. In other words, the suggested hybrid
storage system consists of two tanks: a water tank as a SHS medium;
and a paraffin tank as a LHS medium. A computing program was
used to find the optimized time schedule of charging the storage
tanks during each day, according to the solar radiation conditions.
The results show that the use of such system can improve the
capability of energy gathering comparing to the individual water
storage tank during the cold months of the year. Of course, because
of the solar radiation angles and shorten daylight in December &
January, the performance will be the same as the simple solar water
heaters (in the northern hemisphere). But the extra energy stored in
November, February, March & April, can be useful for heating a
small room for 3 hours during the cold days.
Abstract: The principal objective of a water treatment plant is to
produce water that satisfies a set of drinking water quality standards
at a reasonable price to the consumers. The gravel-bed flocculator
provide a simple and inexpensive design for flocculation in small
water treatment plants (less than 5000 m3/day capacity). The packed
bed of gravel provides ideal conditions for the formation of compact
settleable flocs because of continuous recontact provided by the
sinuous flow of water through the interstices formed by the gravel.
The field data which were obtained from the operation of the
water supply treatment unit cover the physical, chemical and
biological water qualities of the raw and settled water as obtained by
the operation of the treatment unit. The experiments were carried out
with the aim of assessing the efficiency of the gravel filter in
removing the turbidity, pathogenic bacteria, from the raw water. The
water treatment plant, which was constructed for the treatment of
river water, was in principle a rapid sand filter.
The results show that the average value of the turbidity level of
the settled water was 4.83 NTU with a standard deviation of turbidity
2.893 NTU. This indicated that the removal efficiency of the
sedimentation tank (gravel filter) was about 67.8 %. for pH values
fluctuated between 7.75 and 8.15, indicating the alkaline nature of
the raw water of the river Shatt Al-Hilla, as expected. Raw water pH
is depressed slightly following alum coagulation. The pH of the
settled water ranged from 7.75 to a maximum of 8.05.
The bacteriological tests which were carried out on the water
samples were: total coliform test, E-coli test, and the plate count test.
In each test the procedure used was as outlined in the Standard
Methods for the Examination of Water and Wastewater (APHA,
AWWA, and WPCF, 1985). The gravel filter exhibit a low
performance in removing bacterial load. The percentage bacterial
removal, which is maximum for total plate count (19%) and
minimum for total coliform (16.82%).
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: A 7-step method (with 25 sub-steps) to assess risk of
air pollutants is introduced. These steps are: pre-considerations,
sampling, statistical analysis, exposure matrix and likelihood, doseresponse
matrix and likelihood, total risk evaluation, and discussion
of findings. All mentioned words and expressions are wellunderstood;
however, almost all steps have been modified, improved,
and coupled in such a way that a comprehensive method has been
prepared. Accordingly, the SADRA (Statistical Analysis-Driven Risk
Assessment) emphasizes extensive and ongoing application of
analytical statistics in traditional risk assessment models. A Sulfur
Dioxide case study validates the claim and provides a good
illustration for this method.
Abstract: A new paradigm for software design and development models software by its business process, translates the model into a process execution language, and has it run by a supporting execution engine. This process-oriented paradigm promotes modeling of software by less technical users or business analysts as well as rapid development. Since business process models may be shared by different organizations and sometimes even by different business domains, it is interesting to apply a technique used in traditional software component technology to design reusable business processes. This paper discusses an approach to apply a technique for software component fabrication to the design of process-oriented software units, called process components. These process components result from decomposing a business process of a particular application domain into subprocesses with an aim that the process components can be reusable in different process-based software models. The approach is quantitative because the quality of process component design is measured from technical features of the process components. The approach is also strategic because the measured quality is determined against business-oriented component management goals. A software tool has been developed to measure how good a process component design is, according to the required managerial goals and comparing to other designs. We also discuss how we benefit from reusable process components.
Abstract: Col is a classic combinatorial game played on graphs
and to solve a general instance is a PSPACE-complete problem.
However, winning strategies can be found for some specific graph
instances. In this paper, the solution of Col on complete k-ary trees
is presented.
Abstract: The present study explains the effect of aggregate
gradation on moisture damage in bituminous mixes. Three types of
aggregate gradation and two types of binder; VG-30 and Polymer
modified bitumen (PMB-40) are used. Moisture susceptibility tests
like retained stability and tensile strength ratio (TSR) and static creep
test are conducted on Marshall specimens. The creep test was also
conducted for conditioned and unconditioned specimens to observe
the effect of moisture on creep behaviour. The results indicate that
Marshall stability value is higher in PMB-40 mix than VG-30 mixes.
Moisture susceptibility of PMB-40 mixes is low when compared with
mix using VG-30. The reduction in retained stability, and indirect
tensile strength and increase in creep are evaluated for finer, coarser
and normal gradation of aggregate to observe the effect of gradation
on moisture susceptibility of mixes. The retained stability is least
affected when compared with other moisture susceptibility
parameters
Abstract: Intelligent systems based on machine learning
techniques, such as classification, clustering, are gaining wide spread
popularity in real world applications. This paper presents work on
developing a software system for predicting crop yield, for example
oil-palm yield, from climate and plantation data. At the core of our
system is a method for unsupervised partitioning of data for finding
spatio-temporal patterns in climate data using kernel methods which
offer strength to deal with complex data. This work gets inspiration
from the notion that a non-linear data transformation into some high
dimensional feature space increases the possibility of linear
separability of the patterns in the transformed space. Therefore, it
simplifies exploration of the associated structure in the data. Kernel
methods implicitly perform a non-linear mapping of the input data
into a high dimensional feature space by replacing the inner products
with an appropriate positive definite function. In this paper we
present a robust weighted kernel k-means algorithm incorporating
spatial constraints for clustering the data. The proposed algorithm
can effectively handle noise, outliers and auto-correlation in the
spatial data, for effective and efficient data analysis by exploring
patterns and structures in the data, and thus can be used for
predicting oil-palm yield by analyzing various factors affecting the
yield.
Abstract: This article presents the analysis of experimental values regarding cracking pattern, specific strains and deformability for reinforced high strength concrete beams. The beams have the concrete class C80/95 and a longitudinal reinforcement ratio of 2.01%, respectively 3.39%. The elements were subjected to flexure under static short-term and long-term loading. The experimental values are compared with calculation values using the design relationships according to Eurocode 2.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: The importance of inter-organizational system (IOS)
has been increasingly recognized by organizations. However, IOS
adoption has proved to be difficult and, at this stage, why this is so is
not fully uncovered. In practice, benefits have often remained
concentrated, primarily accruing to the dominant party, resulting in
low rates of adoption and usage, and often culminating in the failure
of the IOS. The main research question is why organizations initiate
or join IOS and what factors influence their adoption and use levels.
This paper reviews the literature on IOS adoption and proposes a
theoretical framework in order to identify the critical factors to
capture a complete picture of IOS adoption. With our proposed
critical factors, we are able to investigate their relative contributions
to IOS adoption decisions. We obtain findings that suggested that
there are five groups of factors that significantly affect the adoption
and use decision of IOS in the Supply Chain Management (SCM)
context: 1) interorganizational context, 2) organizational context, 3)
technological context, 4) perceived costs, and 5) perceived benefits.
Abstract: MABENA model is a complementary model in
comparison with traditional models such as HCMS, CMS and etc.
New factors, which have effects on preparation of strategic plans and
their sequential order in MABENA model is the platform of
presented road map in this paper.Study review shows, factors such as
emerging new critical success factors for strategic planning,
improvement of international strategic models, increasing the
maturity of companies and emerging new needs leading to design a
new model which can be responsible for new critical factors and
solve the limitations of previous strategic management models.
Preparation of strategic planning need more factors than introduced
in traditional models. The needed factors includes determining future
Critical Success Factors and competencies, defining key processes,
determining the maturity of the processes, considering all aspects of
the external environment etc. Description of aforementioned
requirements, the outcomes and their order is developing and
presenting the MABENA model-s road map in this paper. This study
presents a road map for strategic planning of the Iranian
organizations.