Abstract: The accomplished study is based on the appointment
and identification of ageing effects and according to this absorption
of moisture of aircraft cabin components over the life-cycle. In the
first step of the study ceiling panels from same age and from the
same aircraft cabin have been examined according to weight changes
depending on the position in the aircraft cabin. In the second step of
the study different aged ceiling panels have been examined
concerning deflection, weight changes and the acoustic sound
transmission loss. To prove the assumption of water absorption
within the study and with the theoretical background from literature
and scientific papers, an older test panel was exposed extreme
thermal conditions (humidity and temperature) within a climate
chamber to show that there is a general ingress of water to cabin
components and that this ingress of water leads to the change of
different mechanical properties.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: This study examined the underlying dimensions of
brand equity in the chocolate industry. For this purpose, researchers
developed a model to identify which factors are influential in
building brand equity. The second purpose was to assess brand
loyalty and brand images mediating effect between brand attitude,
brand personality, brand association with brand equity. The study
employed structural equation modeling to investigate the causal
relationships between the dimensions of brand equity and brand
equity itself. It specifically measured the way in which consumers’
perceptions of the dimensions of brand equity affected the overall
brand equity evaluations. Data were collected from a sample of
consumers of chocolate industry in Iran. The results of this empirical
study indicate that brand loyalty and brand image are important
components of brand equity in this industry. Moreover, the role of
brand loyalty and brand image as mediating factors in the intention of
brand equity are supported. The principal contribution of the present
research is that it provides empirical evidence of the
multidimensionality of consumer based brand equity, supporting
Aaker´s and Keller´s conceptualization of brand equity. The present
research also enriched brand equity building by incorporating the
brand personality and brand image, as recommended by previous
researchers. Moreover, creating the brand equity index in chocolate
industry of Iran particularly is novel.
Abstract: With deep development of software reuse, componentrelated
technologies have been widely applied in the development of
large-scale complex applications. Component identification (CI) is
one of the primary research problems in software reuse, by analyzing
domain business models to get a set of business components with high
reuse value and good reuse performance to support effective reuse.
Based on the concept and classification of CI, its technical stack is
briefly discussed from four views, i.e., form of input business models,
identification goals, identification strategies, and identification
process. Then various CI methods presented in literatures are
classified into four types, i.e., domain analysis based methods,
cohesion-coupling based clustering methods, CRUD matrix based
methods, and other methods, with the comparisons between these
methods for their advantages and disadvantages. Additionally, some
insufficiencies of study on CI are discussed, and the causes are
explained subsequently. Finally, it is concluded with some
significantly promising tendency about research on this problem.
Abstract: Product Data Management (PDM) systems for Computer
Aided Design (CAD) file management are widely established
in design processes. This management system is indispensable for
design collaboration or when design task distribution is present. It is
thus surprising that engineering design curricula has not paid much
attention in the education of PDM systems. This is also the case
for eduction of ecodesign and environmental evaluation of products.
With the rise of sustainability as a strategic aspect in companies,
environmental concerns are becoming a key issue in design. This
paper discusses the establishment of a PDM platform to be used
among technical and vocational schools in Austria. The PDM system
facilitates design collaboration among these schools. Further, it will
be discussed how the PDM system has been prepared in order to
facilitate environmental evaluation of parts, components and subassemblies
of a product. By integrating a Business Intelligence
solution, environmental Life Cycle Assessment and communication
of results is enabled.
Abstract: Structural redundancy is an interesting point in
seismic design of structures. Initially, the structural redundancy is
described as indeterminate degree of a system. Although many definitions are presented for redundancy in structures, recently the
definition of structural redundancy has been related to the configuration of structural system and the number of lateral load
transferring directions in the structure. The steel frames with infill walls are general systems in the constructing of usual residential buildings in some countries. It is
obviously declared that the performance of structures will be affected by adding masonry infill walls. In order to investigate the effect of
infill walls on the redundancy of the steel frame which constructed
with masonry walls, the components of redundancy including redundancy variation index, redundancy strength index and
redundancy response modification factor were extracted for the
frames with masonry infills. Several steel frames with typical storey number and various numbers of bays were designed and considered.
The redundancy of frames with and without infill walls was evaluated by proposed method. The results showed the presence of infill causes increase of redundancy.
Abstract: This article presents a resistorless current-mode firstorder allpass filter based on second generation current controlled current conveyors (CCCIIs). The features of the circuit are that: the pole frequency can be electronically controlled via the input bias current: the circuit description is very simple, consisting of 2 CCCIIs and single grounded capacitor, without any external resistors and component matching requirements. Consequently, the proposed circuit is very appropriate to further develop into an integrated circuit. Low input and high output impedances of the proposed configuration enable the circuit to be cascaded in current-mode without additional current buffers. The PSpice simulation results are depicted. The given results agree well with the theoretical anticipation. The application example as a current-mode quadrature oscillator is included.
Abstract: In this work a new platform for mobile-health systems is
presented. System target application is providing decision support to
rescue corps or military medical personnel in combat areas. Software
architecture relies on a distributed client-server system that manages a
wireless ad-hoc networks hierarchy in which several different types of
client operate. Each client is characterized for different hardware and
software requirements. Lower hierarchy levels rely in a network of
completely custom devices that store clinical information and patient
status and are designed to form an ad-hoc network operating in the
2.4 GHz ISM band and complying with the IEEE 802.15.4 standard
(ZigBee). Medical personnel may interact with such devices, that are
called MICs (Medical Information Carriers), by means of a PDA
(Personal Digital Assistant) or a MDA (Medical Digital Assistant),
and transmit the information stored in their local databases as well as
issue a service request to the upper hierarchy levels by using IEEE
802.11 a/b/g standard (WiFi). The server acts as a repository that
stores both medical evacuation forms and associated events (e.g., a
teleconsulting request). All the actors participating in the diagnostic
or evacuation process may access asynchronously to such repository
and update its content or generate new events. The designed system
pretends to optimise and improve information spreading and flow
among all the system components with the aim of improving both
diagnostic quality and evacuation process.
Abstract: The liquid cargo contained in a partly-filled road tank
vehicle is prone to dynamic slosh movement when subjected to
external disturbances. The slosh behavior has been identified as a
significant factor impairing the safety of liquid cargo transportation.
The laboratory experiments have been conducted for analyzing fluid
slosh in partly filled tanks. The experiment results measured under
forced harmonic excitations reveal the three-dimensional nature of
the fluid motion and coupling between the lateral and longitudinal
fluid slosh at resonance. Several spectral components are observed
for the transient slosh forces, which can be associated with the
excitation, resonance, and beat frequencies. The peak slosh forces
and moments in the vicinity of resonance are significantly larger than
those of the equivalent rigid mass. Due to the nature of coupling
between sloshing fluid and vehicle body, the issue of the dynamic
fluid-structure interaction is essential in the analysis of tank-vehicle
dynamics. A dynamic pitch plane model of a Tridem truck
incorporated the fluid slosh dynamics is developed to analyze the
fluid-vehicle interaction under the straight-line braking maneuvers.
The results show that the vehicle responses are highly associated
with the characteristics of fluid slosh force and moment.
Abstract: Global competition is tightening and companies have
to think how to remain competitive. The main aim of this paper is to
discuss how Finnish foundries will remain competitive. To fulfil the
aim, we conducted interviews in nine companies using castings and
analysed buyer–supplier relationships, current competitive
advantages of Finnish foundries and customer perspectives on how
Finnish foundries remain competitive. We found that the customerfoundry
relationship is still closer to traditional subcontracting than
partnering and general image of foundries is negative. Current
competitive advantages of Finnish foundries include designing
cooperation, proximity and flexibility. Casting users state that
Finnish foundries should sell their know-how and services instead of
their capacity, concentrate on prototype, single and short series
castings and supply ready-to-install cast components directly to
customers- assembly lines.
Abstract: In this article an isotropic linear elastic half-space with
a cylindrical cavity of finite length is considered to be under the
effect of a ring shape time-harmonic torsion force applied at an
arbitrary depth on the surface of the cavity. The equation of
equilibrium has been written in a cylindrical coordinate system. By
means of Fourier cosine integral transform, the non-zero
displacement component is obtained in the transformed domain. With
the aid of the inversion theorem of the Fourier cosine integral
transform, the displacement is obtained in the real domain. With the
aid of boundary conditions, the involved boundary value problem for
the fundamental solution is reduced to a generalized Cauchy singular
integral equation. Integral representation of the stress and
displacement are obtained, and it is shown that their degenerated
form to the static problem coincides with existing solutions in the
literature.
Abstract: We identify clawback triggers from firms- proxy
statements (Form DEF 14A) and use the likelihood of restatements to
proxy for financial reporting quality. Based on a sample of 578 U.S.
firms that voluntarily adopt clawback provisions during 2003-2009,
when restatement-based triggers could be decomposed into two types:
fraud and unintentional error, and we do observe the evidence that
using fraud triggers is associated with high financial reporting quality.
The findings support that fraud triggers can enhance deterrent effect of
clawback provision by establishing a viable disincentive against fraud,
misconduct, and otherwise harmful acts. These results are robust to
controlling for the compensation components, to different sample
specifications and to a number of sensitivity.
Abstract: Management Systems are powerful tools for businesses
to manage quality , environmental and occupational health and safety
requirements . where once these systems were considered as stand
alone control mechanisms , industry is now opting to increase the
efficiency of these documented systems through a more integrated
approach . System integration offers a significant step forward, where
there are similarities between system components , reducing
duplication and adminstration costs and increasing efficiency .
At first , this paper reviews integrated management system structure
and its benefits. The second part of this paper focuses on the one
example implementation of such a system at Imam Khomeini
Hospital and in final part of the paper will be discuss outcomes of
that proccess .
Abstract: In this project, a tele-operated anthropomorphic
robotic arm and hand is designed and built as a versatile robotic arm
system. The robot has the ability to manipulate objects such as pick
and place operations. It is also able to function by itself, in
standalone mode.
Firstly, the robotic arm is built in order to interface with a personal
computer via a serial servo controller circuit board. The circuit board
enables user to completely control the robotic arm and moreover,
enables feedbacks from user. The control circuit board uses a
powerful integrated microcontroller, a PIC (Programmable Interface
Controller). The PIC is firstly programmed using BASIC (Beginner-s
All-purpose Symbolic Instruction Code) and it is used as the 'brain'
of the robot. In addition a user friendly Graphical User Interface
(GUI) is developed as the serial servo interface software using
Microsoft-s Visual Basic 6.
The second part of the project is to use speech recognition control
on the robotic arm. A speech recognition circuit board is constructed
with onboard components such as PIC and other integrated circuits. It
replaces the computers- Graphical User Interface. The robotic arm is
able to receive instructions as spoken commands through a
microphone and perform operations with respect to the commands
such as picking and placing operations.
Abstract: This paper presents a new system developed in Java®
for pattern recognition and pattern summarisation in multi-band
(RGB) satellite images. The system design is described in some
detail. Results of testing the system to analyse and summarise
patterns in SPOT MS images and LANDSAT images are also
discussed.
Abstract: The analytical prediction of the decay heat results
from the fast neutron fission of actinides was initiated under a project, 10-MAT1134-3, funded by king Abdulaziz City of Science
and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, managed by a team
from King Abdulaziz University (KAU), Saudi Arabia, and
supervised by Argonne National Laboratory (ANL) has collaborated
with KAU's team to assist in the computational analysis. In this paper, the numerical solution of coupled linear differential equations
that describe the decays and buildups of minor fission product MFA, has been used to predict the total decay heat and its components from the fast neutron fission of 235U and 239Pu. The reliability of the present approach is illustrated via systematic
comparisons with the measurements reported by the University of
Tokyo, in YAYOI reactor.
Abstract: this scientific article considers the peculiarities of
ecology of culture and ecological outlook from cultural and
anthropological aspect of Turkic languages speaking peoples in the
Central Asia. The ecology of culture of Turkic languages speaking
peoples in the Central Asia, formed under the influence of climatic,
geographical, economic, religious, ethno cultural and political factors
and defining the originality of traditions which have laid down in its
basis and functioned, as its components, causes an interest and
urgency simultaneously, representing the sample of life of the Person
in the World by which it is necessary to be guided today.
Abstract: In this paper we present an approach for 3D face
recognition based on extracting principal components of range
images by utilizing modified PCA methods namely 2DPCA and
bidirectional 2DPCA also known as (2D) 2 PCA.A preprocessing
stage was implemented on the images to smooth them using median
and Gaussian filtering. In the normalization stage we locate the nose
tip to lay it at the center of images then crop each image to a standard
size of 100*100. In the face recognition stage we extract the principal
component of each image using both 2DPCA and (2D) 2 PCA.
Finally, we use Euclidean distance to measure the minimum distance
between a given test image to the training images in the database. We
also compare the result of using both methods. The best result
achieved by experiments on a public face database shows that 83.3
percent is the rate of face recognition for a random facial expression.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.