Abstract: This work studies the effect of thickness on structural
and electrical properties of CuAlS2 thin films grown by two stage
vacuum thermal evaporation technique. CuAlS2 thin films of
thicknesses 50nm, 100nm and 200nm were deposited on suitably
cleaned corning 7059 glass substrate at room temperature (RT). In
the first stage Cu-Al precursors were grown at room temperature by
thermal evaporation and in the second stage Cu-Al precursors were
converted to CuAlS2 thin films by sulfurisation under sulfur
atmosphere at the temperature of 673K. The structural properties of
the films were examined by X-ray diffraction (XRD) technique while
electrical properties of the specimens were studied using four point
probe method. The XRD studies revealed that the films are of
crystalline in nature having tetragonal structure. The variations of the
micro-structural parameters, such as crystallite size (D), dislocation
density ( ), and micro-strain ( ), with film thickness were
investigated. The results showed that the crystallite sizes increase as
the thickness of the film increases. The dislocation density and
micro-strain decreases as the thickness increases. The resistivity ( )
of CuAlS2 film is found to decrease with increase in film thickness,
which is related to the increase of carrier concentration with film
thickness. Thus thicker films exhibit the lowest resistivity and high
carrier concentration, implying these are the most conductive films.
Low electrical resistivity and high carrier concentration are widely
used as the essential components in various optoelectronic devices
such as light-emitting diode and photovoltaic cells.
Abstract: Not all proteins have the same nutritional value, since
protein quality strongly depends on its amino acid composition and
digestibility. The meat of game animals could be a high protein
source because of its well-balanced essential amino acids
composition. Investigations about biochemical composition of game
meat such as wild boar (Sus scrofa scrofa), roe deer (Capreolus
capreolus) and beaver (Castor fiber) are not very much. Therefore,
the aim of the investigation was evaluate protein composition of
game meat hunted in Latvia. The biochemical analysis, evaluation of
connective tissue and essential amino acids in meat samples were
done, the amino acids score were calculate. Results of analysis
showed that protein content 20.88-22.05% of all types of meat
samples is not different statistically. The content of connective tissue
from 1.3% in roe deer till 1.5% in beaver meat allowed classified
game animal as high quality meat. The sum of essential amino acids
in game meat samples were determined 7.05–8.26g100g-1. Roe deer
meat has highest protein content and lowest content of connective
tissues among game meat hunted in Latvia. Concluded that amino
acid score for limiting amino acids phenylalanine and tyrosine is high
and shows high biological value of game meat.
Abstract: In this paper, a single phase soft switched Zero Voltage Transition and Zero Current Transition (ZVT-ZCT) Power Factor Correction (PFC) boost converter is proposed. In the proposed PFC converter, the main switch turns on with ZVT and turns off with ZCT without any additional voltage or current stresses. Auxiliary switch turns on and off with zero current switching (ZCS). Also, the main diode turns on with zero voltage switching (ZVS) and turns off with ZCS. The proposed converter has features like low cost, simple control and structure. The output current and voltage are controlled by the proposed PFC converter in wide line and load range. The theoretical analysis of converter is clarified and the operating steps are given in detail. The simulation results of converter are obtained for 500 W and 100 kHz. It is observed that the semiconductor devices operate with soft switching (SS) perfectly. So, the switching power losses are minimum. Also, the proposed converter has 0.99 power factor with sinusoidal current shape.
Abstract: The purpose of this study is to investigate the efficacy of the solution-focused brief therapy on improving the psychological wellbeing of family supervisor woman. This study has been carried out by semi-experimental method and in the form of pre-test, post-test performance on two groups (experimental and control), so that one sample group of 30 individuals was randomly achieved and were randomly divided in two groups of experimental (n=15) and control (n=15). To collect data, Ryff scale psychological wellbeing was used. After conducting pre-test (RSPWB) for two experimental and control groups, Solution-focused brief therapy interference was conducted on the experimental group during five two-hour sessions. Finally, Ryff scale psychological wellbeing was reused for the two groups as post-test and achieved outcomes that were analyzed using covariance. The results indicated that the significant increase of average marks of the experimental group in psychological wellbeing had better function than that of the control group. Finally, solution-focused brief therapy for improving psychological well-being of family supervisor women has a suitable capability and could be used in this way.
Abstract: The purpose of this study is to investigate the efficacy of solution-focused group therapy on improving the depressed mothers of child abuser families. This study was carried out in the form of a semi-pilot, pre-test and post-test on two groups (experimental and control). Subjects include all mothers and their children that are the members of Shush and Naser Khosro child home. Beck Depression Inventory and Child Trauma Questionnaire were used to collect data. First, child abuse questionnaire was completed by children, Then Beck Depression Inventory was completed by their mothers that 22 of them were recognized as depressed and randomly divided in two groups of experimental and control. After applying pre-test for both of these groups, the intervention of solution- focused group therapy was performed in five sessions on experimental group. Finally, post-test was applied on both groups and subsequently in a month, follow-up test was performed. T-test, multivariate variance, and repeated measurement analysis of variance were used to analyze the data. According to the findings, it can be concluded that this therapy leads to the improvement of depressed mother's mood. As a result, the intervention of solution-focused group therapy is useful in order to improve the depressing mood of mothers of child abuser families.
Abstract: In this paper, an improved active snubber cell is proposed on account of soft switching (SS) family of pulse width modulation (PWM) DC-DC converters. The improved snubber cell provides zero-voltage transition (ZVT) turn on and zero-current transition (ZCT) turn off for main switch. The snubber cell decreases EMI noise and operates with SS in a wide range of line and load voltages. Besides, all of the semiconductor devices in the converter operate with SS. There is no additional voltage and current stress on the main devices. Additionally, extra voltage stress does not occur on the auxiliary switch and its current stress is acceptable value. The improved converter has a low cost and simple structure. The theoretical analysis of converter is clarified and the operating states are given in detail. The experimental results of converter are obtained by prototype of 500 W and 100 kHz. It is observed that the experimental results and theoretical analysis of converter are suitable with each other perfectly.
Abstract: The main objective of this paper is to establish the relationship between models of state organization and the various types of collective identity expressed by the Spanish. The question of nationalism and identity ascription in Spain has always been a topic of special importance due to the presence in that country of territories where the population emits very different opinions of nationalist sentiment than the rest of Spain. The current situation of sovereignty challenge of Catalonia to the central government exemplifies the importance of the subject matter. In order to analyze this process of interrelation, we use a secondary data mining by applying the multiple correspondence analysis technique (MCA). As a main result a typology of four types of expression of collective identity based on models of State organization are shown, which are connected with the party position on this issue.
Abstract: Copreneurship is a term used to describe the business
pattern of operations run by married couples who share commitment,
goals, and responsibilities in handling a business. Research conducted
overseas showed that copreneurship business activities grew quickly
and played a role in elevating families’ and nations’ socio-economic
standards. In Malaysia, copreneurship has long been cultivated by
spouses. Thus, this study aimed to explore the factors that motivate
married partners to start a copreneurship business, and who is the
dominant partner in the management of this business. The study
participants are four entrepreneurial couples who are SME business
operators selected through purposive sampling. In-depth interviews
and direct observation were used as methods of measurement for
triangulation of qualitative data in this study. The findings of the
interviews were administered using NVivo 8.0 software. The result
shows that freedom is a key factor that drives entrepreneurs to set up
copreneurship businesses, and that the husband dominates the
management aspects of the business. The study gives an overview of
the parties involved in entrepreneurship to provide understanding of
the copreneurship concept as it is practiced. This study provides
academic value by creating understanding of the importance of a
harmonious family institution specifically for forming entrepreneurs
in the familial environment in Malaysia.
Abstract: Despite the benefits of innovation diffusion in the
South African public service, implementation thereof seems to be
problematic, particularly with regard to e-governance which would
enhance the quality of service delivery, especially accessibility,
choice, and mode of operation. This paper reports on differences
between the public service and the private sector in terms of
innovation diffusion. Innovation diffusion will be investigated to
explore identified obstacles that are hindering successful
implementation of e-governance. The research inquiry is underpinned
by the diffusion of innovation theory, which is premised on the
assumption that innovation has a distinct channel, time, and mode of
adoption within the organisation. A comparative thematic document
analysis was conducted to investigate organisational differences with
regard to innovation diffusion. A similar approach has been followed
in other countries, where the same conceptual framework has been
used to guide document analysis in studies in both the private and the
public sectors. As per the recommended conceptual framework, three
organisational characteristics were emphasised, namely the external
characteristics of the organisation, the organisational structure, and
the inherent characteristics of the leadership. The results indicated
that the main difference in the external characteristics lies in the
focus and the clientele of the private sector. With regard to
organisational structure, private organisations have veto power,
which is not the case in the public service. Regarding leadership,
similarities were observed in social and environmental responsibility
and employees’ attitudes towards immediate supervision. Differences
identified included risk taking, the adequacy of leadership
development, organisational approaches to motivation and
involvement in decision making, and leadership style. Due to the
organisational differences observed, it is recommended that
differentiated strategies be employed to ensure effective innovation
diffusion, and ultimately e-governance. It is recommended that the
results of this research be used to stimulate discussion on ways to
improve collaboration between the mentioned sectors, to capitalise on
the benefits of each sector.
Abstract: In this paper, an attempt has been made to analyze the effect of wall window orientation on Daylight Illuminance Ratio (DIR) and energy saving in a building known as “SODHA BERS COMPLEX (SBC)” at Varanasi, UP, India. The building has been designed incorporating all passive concepts for thermal comfort as well daylighting concepts to maximize the use of natural daylighting for the occupants in the day to day activities. The annual average DIR and the energy saving has been estimated by using the DIR model for wall window with different orientations under clear sky condition. It has been found that for south oriented window the energy saving per square meter is more compared to the other orientations due to the higher level of solar insolation for the south window in northern hemisphere whereas energy saving potential is minimum for north oriented wall window. The energy saving potential was 26%, 81% and 51% higher for east, south and west oriented window in comparison to north oriented window. The average annual DIR has same trends of variation as the annual energy saving and it is maximum for south oriented window and minimum for north oriented window.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: Flue gas desulfurization gypsum (FGD) is a waste
material arouse from coal power plants. Hydroxyapatite (HAP) is a
biomaterial with porous structure. In this study, FGD gypsum which
retrieved from coal power plant in Turkey was characterized and
HAP particles which can be used as an adsorbent in wastewater
treatment application were synthesized from the FGD gypsum. The
raw materials are characterized by using X Ray Diffraction (XRD)
and Fourier transform infrared spectroscopy (FT-IR) techniques and
produced HAP are characterized by using XRD. As a result, HAP
particles were synthesized at the molar ratio of 5:10, 5:15, 5:20, 5:24,
at room temperature, in alkaline medium (pH=11) and in 1 hour-reaction
time. Among these conditions, 5:20 had the best result.
Abstract: The objective of this research is to mitigate and prevent
the alkali silica reactivity (ASR) in highway construction projects.
ASR is a deleterious reaction initiated when the silica content of the
aggregate reacts with alkali hydroxides in cement in the presence of
relatively high moisture content. The ASR results in the formation of
an expansive white colored gel-like material which forms the
destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the
State of Arkansas were mixed and mortar bars were poured according
to the ASTM specifications. Mortar bars expansion was measured
versus time and aggregates with potential ASR problems were
detected. Different types of supplementary cementitious materials
(SCMs) were used in remixing mortar bars with highly reactive
aggregates. Length changes for remixed bars proved that different
types of SCMs can be successfully used in reducing the expansive
effect of ASR. SCMs percentage by weight is highly dependent on
the SCM type. The result of this study will help avoiding future
losses due to ASR cracking in construction project and reduce the
maintenance, repair, and replacement budgets required for highways
network.
Abstract: Device-to-device (D2D) communication is considered a
promising technique to provide wireless peer-to-peer communication
services. Due to increasing demand on mobile services, available
spectrum for radio frequency (RF) based communications becomes
scarce. Recently, visible light communications (VLC) has evolved
as a high speed wireless data transmission technology for indoor
environments with abundant available bandwidth. In this paper,
a novel VLC based D2D communication that provides wireless
peer-to-peer communication is proposed. Potential low operating
power devices for an efficient D2D communication over increasing
distance of separation between devices is analyzed. Optical repeaters
(OR) are also proposed to enhance the performance in an environment
where direct D2D communications yield degraded performance.
Simulation results show that VLC plays an important role in
providing efficient D2D communication up to a distance of 1 m
between devices. It is also found that the OR significantly improves
the coverage distance up to 3.5 m.
Abstract: The aim of this article is to identify the measures
companies undertake in order to adapt to the environment as well as
discussing their diversity and effectiveness. The research methods
used in the study include an in-depth analysis of the literature and a
case study, which helps to illustrate the issue in question. Referring to
the concept of agility, which is firmly embedded in the theory of
strategic management and has been developed with the aim of
adapting to the environment and its changes, the paper first examines
different types of adaptation measures for companies. Then the issue
under discussion is illustrated with the example of the company
Hortimex. This company is an eminent representative of the world’s
leading manufacturers of food additives and ingredients. The
company was established in 1988 and is a family business, which in
practice means that it conducts business in a responsible manner,
observing the law and respecting the interests of society and the
environment. The company’s mission is to develop a market in
Poland for the products and solutions offered by their partners and to
share their knowledge of additives in food production and
consumption.
Abstract: This research provides a technical account of
estimating Transition Probability using Time-homogeneous Markov
Jump Process applying by South African HIV/AIDS data from the
Statistics South Africa. It employs Maximum Likelihood Estimator
(MLE) model to explore the possible influence of Transition
Probability of mortality cases in which case the data was based on
actual Statistics South Africa. This was conducted via an integrated
demographic and epidemiological model of South African HIV/AIDS
epidemic. The model was fitted to age-specific HIV prevalence data
and recorded death data using MLE model. Though the previous
model results suggest HIV in South Africa has declined and AIDS
mortality rates have declined since 2002 – 2013, in contrast, our
results differ evidently with the generally accepted HIV models
(Spectrum/EPP and ASSA2008) in South Africa. However, there is
the need for supplementary research to be conducted to enhance the
demographic parameters in the model and as well apply it to each of
the nine (9) provinces of South Africa.
Abstract: Solar water heating is a thermodynamic process of
heating water using sunlight with the help of solar water heater. Thus,
solar water heater is a device used to harness solar energy. In this
paper, a modified solar water heating system (MSWHS) has been
proposed over flat plate collector (FPC) and Evacuated tube collector
(ETC). The modifications include selection of materials other than
glass, and glass wool which are conventionally used for fabricating
FPC and ETC. Some modifications in design have also been
proposed. Its collector is made of double layer of semi-cylindrical
acrylic tubes and fibre reinforced plastic (FRP) insulation base. Water
tank is made of double layer of acrylic sheet except base and north
wall. FRP is used in base and north wall of the water tank. A concept
of equivalent thickness has been utilised for calculating the
dimensions of collector plate, acrylic tube and tank. A thermal model for the proposed design of MSWHS is developed
and simulation is carried out on MATLAB for the capacity of 200L
MSWHS having collector area of 1.6 m2, length of acrylic tubes of
2m at an inclination angle 25° which is taken nearly equal to the
latitude of the given location. Latitude of Allahabad is 24.45° N. The
results show that the maximum temperature of water in tank and tube
has been found to be 71.2°C and 73.3°C at 17:00hr and 16:00hr
respectively in March for the climatic data of Allahabad. Theoretical performance analysis has been carried out by varying
number of tubes of collector, the tank capacity and climatic data for
given months of winter and summer.
Abstract: Sisal leaves were subjected to enzymatic retting
method to extract the sisal fibre. A portion of the fibre was pretreated
with alkali (NaOH), and further treated with benzoyl chloride
and silane treatment reagents. Both the treated and untreated Sisal
fibre composites were used to fabricate the composite by hand lay-up
technique using unsaturated polyester resin. Tensile, flexural, water
absorption, density, thickness swelling and chemical resistant tests
were conducted and evaluated on the composites. Results obtained
for all the parameters showed an increase in the treated fibre
compared to untreated fibre. FT-IR spectra results ascertained the
inclusion of benzoyl and silane groups on the fibre surface. Scanning
electron microscopy (SEM) result obtained showed variation in the
morphology of the treated and untreated fibre. Chemical modification
was found to improve adhesion of the fibre to the matrix, as well as
physico-mechanical properties of the composites.
Abstract: Present paper enumerates highlights of seasonal
variation in floristic composition and ecological strategies for the
management of ‘Gujar Tal’ at Jaunpur in tropical semi-arid region of
eastern U.P. (India). Total composition of macrophytes recorded was
47 from 26 families with maximum 6 plant species of Cyperaceae
from April, 2012 to March, 2013 at certain periodic intervals.
Maximum number of plants (39) was present during winter followed
by (37) rainy and (27) summer seasons. The distribution pattern
depicted that maximum number of plants (27) was of marshy and
swampy habitats usually transitional between land and water.
Abstract: The study was meant to identify the impediments to
female sports management and participation in the selected colleges.
Seven colleges of education in the south west parts of the country
were selected for the study. A total of one hundred and five subjects
were sampled to supply data. Only one hundred adequately
completed and returned, copies of the questionnaire were used for
data analysis. The collected data were analysed descriptively. The
result of the study showed that inadequate fund, personnel, facilities
equipment, supplies, management of sports, supervision and coaching
were some of the impediments to female sports management and
participation. Athletes were not encouraged to participate. Based on
the findings, it was recommended that the government should come
to the aid of the colleges by providing fund and other needs that will
make sports attractive for enhanced participation.