Abstract: Green and renewable energy is getting extraordinary
consideration today, because of ecological concerns made by blazing
of fossil powers. Photovoltaic and wind power generation are the
basic decisions for delivering power in this respects. Producing
power by the sun based photovoltaic systems is known to the world,
yet control makers may get confounded to pick between on-grid and
off-grid systems. In this exploration work, an endeavor is made to
compare the off-grid (stand-alone) and on-grid (grid-connected)
frameworks. The work presents relative examination, between two
distinctive PV frameworks situated at V.V.P. Engineering College,
Rajkot. The first framework is 100 kW remain solitary and the
second is 60 kW network joined. The real-time parameters compared
are; output voltage, load current, power in-flow, power output,
performance ratio, yield factor, and capacity factor. The voltage
changes and the power variances in both frameworks are given
exceptional consideration and the examination is made between the
two frameworks to judge the focal points and confinements of both
the frameworks.
Abstract: A Friction stir welding tool is a critical component to
the success of the process. The tool typically consists of a rotating
round shoulder and a threaded cylindrical pin that heats the work
piece, mostly by friction, and moves the softened alloy around it to
form the joint. In this research work, an attempt has been made to
investigate the relationship between FSW variables mainly tool
profile, rotating speed, welding speed and the mechanical properties
(tensile strength, yield strength, percentage elongation, and micro
hardness) of friction stir welded aluminum alloy 5083 joints. From
the experimental details, it can be assessed that the joint produced by
using Triflute profile tool has contribute superior mechanical and
structural properties as compared to Tapered unthreaded & Threaded
tool for 1000rpm.
Abstract: This paper describes the development of new class of
epoxy based rice husk filled jute reinforced composites. Rice husk
flour is added in 0%, 1%, 3%, 5% by weight. Epoxy resin and
triethylenetetramine (T.E.T.A) is used as matrix and hardener
respectively. It investigates the mechanical properties of the
composites and a comparison is done for monolithic jute composite
and the filled ones. The specimens are prepared according to the
ASTM standards and experimentation is carried out using INSTRON
8801. The result shows that with the increase of filler percentage the
tensile properties increases but compressive and flexural properties
decreases.
Abstract: Brushless DC motors (BLDC) are widely used in
industrial areas. The BLDC motors are driven either by indirect ACAC
converters or by direct AC-AC converters. Direct AC-AC
converters i.e. matrix converters are used in this paper to drive the
three phase BLDC motor and it eliminates the bulky DC link energy
storage element. A matrix converter converts the AC power supply to
an AC voltage of variable amplitude and variable frequency. A
control technique is designed to generate the switching pulses for the
three phase matrix converter. For the control of speed of the BLDC
motor a separate PI controller and Fuzzy Logic Controller (FLC) are
designed and a hysteresis current controller is also designed for the
control of motor torque. The control schemes are designed and tested
separately. The simulation results of both the schemes are compared
and contrasted in this paper. The results show that the fuzzy logic
control scheme outperforms the PI control scheme in terms of
dynamic performance of the BLDC motor. Simulation results are
validated with the experimental results.
Abstract: The question of legal liability over injury arising out
of the import and the introduction of GM food emerges as a crucial
issue confronting to promote GM food and its derivatives. There is a
greater possibility of commercialized GM food from the exporting
country to enter importing country where status of approval shall not
be same. This necessitates the importance of fixing a liability
mechanism to discuss the damage, if any, occurs at the level of
transboundary movement or at the market. There was a widespread consensus to develop the Cartagena
Protocol on Biosafety and to give for a dedicated regime on liability
and redress in the form of Nagoya Kuala Lumpur Supplementary
Protocol on the Liability and Redress (‘N-KL Protocol’) at the
international context. The national legal frameworks based on this
protocol are not adequately established in the prevailing food
legislations of the developing countries. The developing economy
like India is willing to import GM food and its derivatives after the
successful commercialization of Bt Cotton in 2002. As a party to the
N-KL Protocol, it is indispensable for India to formulate a legal
framework and to discuss safety, liability, and regulatory issues
surrounding GM foods in conformity to the provisions of the
Protocol. The liability mechanism is also important in the case where
the risk assessment and risk management is still in implementing
stage. Moreover, the country is facing GM infiltration issues with its
neighbors Bangladesh. As a precautionary approach, there is a need
to formulate rules and procedure of legal liability to discuss any kind
of damage occurs at transboundary trade. In this context, the
proposed work will attempt to analyze the liability regime in the
existing Food Safety and Standards Act, 2006 from the applicability
and domestic compliance and to suggest legal and policy options for
regulatory authorities.
Abstract: The strain intensity and redundant strains, dependent
in multistage TRIP wire drawing processes from values used single
partial reductions, should influence on the intensity of transformation
the retained austenite into martensite and thereby on mechanical
properties of drawn wires. The numerical analysis of drawing
processes with use of Drawing 2D programme, for steel wires made
from TRIP steel with 0,29% has been shown in the work. The change
of strain intensity εc and the values of redundant strain εxy, has been
determined for particular draws in dependence of used single partial
reductions.
Abstract: The purposes of this study were to: 1) investigate
operation conditions of SME automotive part industry in Bangkok
and vicinity and 2) to compare operation problem levels of SME
automotive part industry in Bangkok and vicinity according to the
sizes of the enterprises. Samples in this study included 196
entrepreneurs of SME automotive part industry in Bangkok and
vicinity derived from simple random sampling and calculation from
R. V. Krejcie and D. W. Morgan’s tables. Research statistics included
frequency, percentage, mean, standard deviation, and T-test. The
results revealed that in general the problem levels of SME automotive
part industry in Bangkok and vicinity were high. When considering
in details, it was found that the problem levels were high at every
aspect, i.e. personal, production, export, finance, and marketing
respectively. The comparison of the problem levels according to the
sizes of the enterprises revealed statistically significant differences at
.05. When considering on each aspect, it was found that the aspect
with the statistical difference at .05 included 5 aspects, i.e.
production, marketing, finance, personal, and export. The findings
also showed that small enterprises faced more severe problems than
those of medium enterprises.
Abstract: Value addition to agricultural produce is of possible
potential in reducing poverty, improving food security and
malnutrition, therefore the need to develop small and microenterprises
of sweet potato production. A study was carried out in Nigeria to determine the acceptability
of blends sweet potato (Ipomea batatas) and commodities yellow
maize (Zea mays), millet (Pennisetum glaucum), soybean (Glycine
max), bambara groundnut (Vigna subterranean), guinea corn
(Sorghum vulgare), wheat (Triticum aestivum), and roselle (Hibiscus
sabdariffa) through sensory evaluation. Sweet potato (Ipomea batatas) roots were processed using two
methods: oven and sun drying. The blends were also assessed in
terms of functional, chemical and color properties. Most acceptable blends include BAW (80:20 of sweet
potato/wheat), BBC (80:20 of sweet potato/guinea corn), AAB (60:40
of sweet potato/guinea corn), YTE (100% soybean), TYG (100%
sweet potato), KTN (100% wheat flour), XGP (80:20 of sweet
potato/soybean), XAX (60:40 of sweet potato/wheat), LSS (100%
Roselle), CHK (100% Guinea corn), and ABC (60:40% of sweet
potato/ yellow maize). In addition, carried out chemical analysis
revealed that sweet potato has high percentage of vitamins A and C,
potassium (K), manganese (Mn), calcium (Ca), magnesium (Mg) and
iron (Fe) and fibre content. There is also an increase of vitamin A and
Iron in the blended products.
Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: Hydrogen produced by means of polymer electrolyte
membrane electrolyzer (PEME) is one of the most promising
methods due to clean and renewable energy source. In the process,
some energy loss due to mass transfer through a PEM is caused by
diffusion, electro-osmotic drag, and the pressure difference between
the cathode channel and anode channel. In PEME, water molecules
and ionic particles transferred between the electrodes from anode to
cathode, Extensive mixing of the hydrogen and oxygen at anode
channel due to gases cross-over must be avoided. In recent times the
consciousness of safety issue in high pressure PEME where the
oxygen mix with hydrogen at anode channel could create, explosive
conditions have generated a lot of concern. In this paper, the steady
state and simulation analysis of gases crossover in PEME on the
temperature and pressure effect are presented. The simulations have
been analysis in MATLAB based on the well-known Fick’s Law of
molecular diffusion. The simulation results indicated that as
temperature increases, there is a significant decrease in operating
voltage.
Abstract: The study is the way to identify the problems that
occur in organizing short course’s lifelong learning in the information
and communication technology (ICT) education which are faced by
the lecturer and staff at the Mara Skill Institute and Industrial
Training Institute in Pahang Malaysia. The important aspects of these
issues are classified to five which are selecting the courses
administrative. Fifty lecturers and staff were selected as a respondent.
The sample is selected by using the non-random sampling method
purpose sampling. The questionnaire is used as a research instrument
and divided into five main parts. All the data that gain from the
questionnaire are analyzed by using the SPSS in term of mean,
standard deviation and percentage. The findings showed, there are the
problems occur in organizing the short course for lifelong learning in
ICT education.
Abstract: The main purpose of this study is to assess the
sediment quality and potential ecological risk in marine sediments in
Gymea Bay located in south Sydney, Australia. A total of 32 surface
sediment samples were collected from the bay. Current track
trajectories and velocities have also been measured in the bay. The
resultant trace elements were compared with the adverse biological
effect values Effect Range Low (ERL) and Effect Range Median
(ERM) classifications. The results indicate that the average values of
chromium, arsenic, copper, zinc, and lead in surface sediments all
reveal low pollution levels and are below ERL and ERM values. The
highest concentrations of trace elements were found close to
discharge points and in the inner bay, and were linked with high
percentages of clay minerals, pyrite and organic matter, which can
play a significant role in trapping and accumulating these elements.
The lowest concentrations of trace elements were found to be on the
shoreline of the bay, which contained high percentages of sand
fractions. It is postulated that the fine particles and trace elements are
disturbed by currents and tides, then transported and deposited in
deeper areas. The current track velocities recorded in Gymea Bay had
the capability to transport fine particles and trace element pollution
within the bay. As a result, hydrodynamic measurements were able to
provide useful information and to help explain the distribution of
sedimentary particles and geochemical properties. This may lead to
knowledge transfer to other bay systems, including those in remote
areas. These activities can be conducted at a low cost, and are
therefore also transferrable to developing countries. The advent of
portable instruments to measure trace elements in the field has also
contributed to the development of these lower cost and easily applied
methodologies available for use in remote locations and low-cost
economies.
Abstract: To evaluate the effect of intramuscular administration
of vitamin A in pregnant dairy cows during late stages of pregnancy,
on vitamin A status of neonatal calves, a total of 30 cows were
randomly selected and divided into three groups; two treatment
groups and one control group. Single intramuscular injection of
2000000 IU vitamin A; was carried in 10 dairy cows at 7 months of
pregnancy (group 1). In second group of treated animals (10 cows)
the injection was performed in 8 months of pregnancy (group 2). Ten
pregnant dairy cows were received saline injection as placebo and
selected as control group. Blood samples were collected from
experimental dairy cows at 7 and 8 months of pregnancy as well as
their newborn calves’ pre and after colostrum intake. There was no
significant difference between vitamin A and β-carotene
concentration of dairy cows of three groups in two last months of
pregnancy (P> 0.05). Vitamin A concentration of calves of two
treatment groups before and after receiving of colostrum were
significantly higher than that in control group (P< 0.05). There was
no significant difference between serum concentrations of vitamin A
in calves of two treated groups (P> 0.05). β-Carotene concentration
of serum samples of dairy cows and neonatal calves of three groups
were not significantly different as compared with together. From
results of the present study it can be concluded that single injection of
vitamin A during at 7 or 8 month of pregnancy can significantly
increase level of vitamin A in their colostrum and neonatal calves.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: Frozen shrimp industry plays an important role in the
development of production industry of the country. There has been a
continuing development to response the increasing demand; however,
there have been some problems in running the enterprises. The
purposes of this study are to: 1) investigate problems related to basic
factors in operating frozen shrimp industry based on the
entrepreneurs’ points of view. The enterprises involved in this study
were small and medium industry receiving Thai Frozen Foods
Association. 2) Compare the problems of the frozen shrimp industry
according to their sizes of operation in 3 provinces of the central
region Thailand. Population in this study consisted of 148 managers
from 148 frozen shrimp enterprises Thai Frozen Foods Association
which 77 were small size and 71 were medium size. The data were
analyzed to find percentage, arithmetic mean, standard deviation, and
independent sample T-test with the significant hypothesis at .05. The
results revealed that the problems of the frozen shrimp industries of
both size were in high level. The needs for government supporting
were in high level. The comparison of the problems and the basic
factors between the small and medium size enterprises showed no
statistically significant level. The problems that they mentioned
included raw materials, labors, production, marketing, and the need
for academic supporting from the government sector.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: Agricultural machinery industry plays an important
role in the industrial development especially the production industry
of the country. There has been continuing development responding to
the higher demand of the production. However, the problem in
agricultural machinery production still exists. Thus, the purpose of
this research is to investigate problems on fundamental factors of
industry based on the entrepreneurs’ point of view. The focus was on
the small and medium size industry receiving factory license type
number 0660 from the Department of Industrial Works. The
investigation was on the comparison between the management of the
small and medium size agricultural industry in 3 provinces in the
central region of Thailand. Population in this study consisted of 189
company managers or managing directors, of which 101 were from
the small size and 88 were from the medium size industry. The data
were analyzed to find percentage, arithmetic mean, and standard
deviation with independent sample T-test at the statistical
significance .05. The results showed that the small and medium size
agricultural machinery manufacturers in the central region of
Thailand reported high problems in every aspect. When compared the
problems on basic factors in running the business, it was found that
there was no statistically difference at .05 in managing of the small
and medium size agricultural machinery manufacturers. However,
there was a statistically significant difference between the small and
medium size agricultural machinery manufacturers on the aspect of
policy and services of the government. The problems reported by the
small and medium size agricultural machinery manufacturers were
the services on public tap water and the problem on politic and
stability of the country.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: Selenium is an-antioxidant which is important for
human health enters food chain through crops. In Kenya Zea mays is
consumed by 96% of population hence is a cheap and convenient
method to provide selenium to large number of population. Several
soil factors are known to have antagonistic effects on selenium
speciation hence the uptake by Zea mays. There are no studies in
Kenya that has been done to determine the effects of soil
characteristics (pH, Tcarbon, CEC, Eh) affect accumulation of
selenium in Zea mays grains in Maize Belt in Kenya. About 100 Zea mays grain samples together with 100 soil samples
were collected from the study site put in separate labeled Ziplocs and
were transported to laboratories at room temperature for analysis.
Maize grains were analyzed for selenium while soil samples were
analyzed for pH, Cat Ion Exchange Capacity, total carbon, and
electrical conductivity. The mean selenium in Zea mays grains varied from 1.82 ± 0.76
mg/Kg to 11±0.86 mg/Kg. There was no significant difference
between selenium levels between different grain batches {χ (Df =76)
= 26.04 P= 1.00} The pH levels varied from 5.43± 0.58 to 5.85±
0.32. No significant correlations between selenium in grains and soil
pH (Pearson’s correlations = - 0.143), and between selenium levels in
grains and the four (pH, Tcarbon, CEC, Eh) soil chemical
characteristics {F (4,91) = 0.721 p = 0.579} was observed. It can be concluded that the soil chemical characteristics in the
study site did not significantly affect the accumulation of native
selenium in Zea mays grains.