Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: Since DVB-RCS has been successively implemented, the mobile communication on the multi-beam satellite communication is attractive attention. And the DVB-RCS standard sets up to support mobility of a RCST. In the case of the spot-beam satellite system, the received signal strength does not differ largely between the center and the boundary of the beam. Thus, the RSS based handoff detection algorithm is not benefit to the satellite system as a terrestrial system. Therefore we propose an Adaptive handoff detection algorithm based on RCST mobility information. Our handoff detection algorithm not only can be used as centralized handoff detection algorithm but also removes uncertainties of handoff due to the variation of RSS. Performances were compared with RSS based handoff algorithm. Simulation results show that the proposed handoff detection algorithm not only achieved better handoff and link degradation rate, but also achieved better forward link spectral efficiency.
Abstract: In this presentation, we discuss the use of information technologies in the area of special education for teaching individuals with learning disabilities. Application software which was developed for this purpose is used to demonstrate the applicability of a database integrated information processing system to alleviate the burden of educators. The software allows the preparation of individualized education programs based on the predefined objectives, goals and behaviors.
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: In the paper we presented the possibility of application
collagen gels with active principle-s from marine algae extract and chlorhexidine salt in dental medicine. The hydro-alcoholic extracts
from marine algae have been used as they have been obtained. The extracts from marine algae and chlorhexidine salt (digluconate) are
incorporated in type I non-denatured fibrillar collagen matrixes. In order to obtain therapeutic effects at nanostructure level, it is important to know the rheological characteristics of the relevant mixtures of collagen gels and extracts from marine algae selected for use. In this survey we have studied mixtures made of non-denatured
fibrillar collagen hydro-gels where different concentrations of marine
algae have been incorporated. Based on the data obtained for the
shearing tensions, we have traced the rheograms – the diagrams for shearing tensions depending on the shearing speed values – from
which we have calculated the apparent viscosities as ratios between shearing tension and speed values, which have been figured in
relation to the shearing speed values, with a view to levelling
dependency.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: Since the driving speed and control accuracy of
commercial optical disk are increasing significantly, it needs an
efficient controller to monitor the track seeking and following
operations of the servo system for achieving the desired data
extracting response. The nonlinear behaviors of the actuator and servo
system of the optical disk drive will influence the laser spot
positioning. Here, the model-free fuzzy control scheme is employed to
design the track seeking servo controller for a d.c. motor driving
optical disk drive system. In addition, the sliding model control
strategy is introduced into the fuzzy control structure to construct a
1-D adaptive fuzzy rule intelligent controller for simplifying the
implementation problem and improving the control performance. The
experimental results show that the steady state error of the track
seeking by using this fuzzy controller can maintain within the track
width (1.6 μm ). It can be used in the track seeking and track
following servo control operations.
Abstract: In this study, the possibility of using potato as a
substrate for glutamic acid production by Brevibacterium linens
was investigated. For preparation of fermentation medium, potato
was hydrolyzed by hydrochloridric acid. The medium contained
potato hydrolysate, tween 80, mineral solution, glucose, and
potassium hydrogen phosphate. The initial pH of the medium was
adjusted to 7-7.5. For achieving the optimum time with maximum
yield, the beakers containing the medium and the inoculums were
incubated in a rotary water bath flask shaker for one to five days.
Thin layer choromatography was used for quantitative and
qualitative assay of the glutamic acid produced. The results
revealed that as fermentation time increased, pH of the
fermentation medium significantly decreased (P
Abstract: The burst noise is a kind of noises that are destructive
and frequently found in semiconductor devices and ICs, yet detecting
and removing the noise has proved challenging for IC designers or users. According to the properties of burst noise, a methodological
approach is presented (proposed) in the paper, by which the burst noise
can be analysed and detected in time domain. In this paper, principles
and properties of burst noise are expounded first, Afterwards,
feasibility (viable) of burst noise detection by means of wavelet
transform in the time domain is corroborated in the paper, and the multi-resolution characters of Gaussian noise, burst noise and blurred
burst noise are discussed in details by computer emulation. Furthermore, the practical method to decide parameters of wavelet
transform is acquired through a great deal of experiment and data statistics. The methodology may yield an expectation in a wide variety of applications.
Abstract: The purpose of this paper is to develop a typology
based on market orientation (MO) and innovation orientation (IO),
and to illustrate to what extent housing companies in Sweden fit
within this framework. A qualitative study on 11 public housing
companies in the central part of Sweden has been conducted by the
help of open and semi-structured questions for data collection. Four
public housing company types- i.e. reactive prospector, proactive
prospector, reactive defender and proactive defender have been
identified by the combination of MO-IO dimensions. Future research
can include other dimensions like entrepreneurship and network to
observe how it particularly affects MO. An empirical study can
compare public and private housing companies on the basis of MO
and IO dimensions. One major contribution of the paper is the
proposition of typology which can be used to describe public housing
companies and deciding their future course of actions.
Abstract: Several different cements have been tested to evaluate
their potential to leach calcium, chromium and aluminum ions in soft
water environment. The research allows comparing some different
cements in order to the potential risk of water contamination. This
can be done only in the same environment. To reach the results in
reasonable short time intervals and to make heavy metals
measurements with high accuracy, demineralized water was used. In
this case the conditions of experiments are far away from the water
supply practice, but short time experiments and measurably high
concentrations of elements in the water solution are an important
advantage. Moreover leaching mechanisms can be recognized, our
experiments reported here refer to this kind of cements evaluation.
Abstract: The velocity of a moving point in a general path is the vector quantity, which has both magnitude and direction. The magnitude or the direction of the velocity vector can change over time as a result of acceleration that the time rate of velocity changes. Acceleration analysis is important because inertial forces and inertial torques are proportional to rectilinear and angular accelerations accordingly. The loads must be determined in advance to ensure that a machine is adequately designed to handle these dynamic loads. For planar motion, the vector direction of acceleration is commonly separated into two elements: tangential and centripetal or radial components of a point on a rotating body. All textbooks in physics, kinematics and dynamics of machinery consider the magnitude of a radial acceleration at condition when a point rotates with a constant angular velocity and it means without acceleration. The magnitude of the tangential acceleration considered on a basis of acceleration for a rotating point. Such condition of presentation of magnitudes for two components of acceleration logically and mathematically is not correct and may cause further confusion in calculation. This paper presents new analytical expressions of the radial and absolute accelerations of a rotating point with acceleration and covers the gap in theoretical study of acceleration analysis.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: Content-based Image Retrieval (CBIR) aims at searching image databases for specific images that are similar to a given query image based on matching of features derived from the image content. This paper focuses on a low-dimensional color based indexing technique for achieving efficient and effective retrieval performance. In our approach, the color features are extracted using the mean shift algorithm, a robust clustering technique. Then the cluster (region) mode is used as representative of the image in 3-D color space. The feature descriptor consists of the representative color of a region and is indexed using a spatial indexing method that uses *R -tree thus avoiding the high-dimensional indexing problems associated with the traditional color histogram. Alternatively, the images in the database are clustered based on region feature similarity using Euclidian distance. Only representative (centroids) features of these clusters are indexed using *R -tree thus improving the efficiency. For similarity retrieval, each representative color in the query image or region is used independently to find regions containing that color. The results of these methods are compared. A JAVA based query engine supporting query-by- example is built to retrieve images by color.
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: Design should be viewed concurrently by three ways
as transformation, flow and value generation. An innovative approach
to solve design – related problems is described as the integrated
product - process design. As a foundation for a formal framework
consisting of organizing principles and techniques, Work Structuring
has been developed to guide efforts in the integration that enhances
the development of operation and process design in alignment with
product design.
Vietnam construction projects are facing many delays, and cost
overruns caused mostly by design related problems. A better design
management that integrates product and process design could resolve
these problems. A questionnaire survey and in – depth interviews
were used to investigate the feasibility of applying Work Structuring
to construction projects in Vietnam.
The purpose of this paper is to present the research results and to
illustrate the possible problems and potential solutions when Work
Structuring is implemented to construction projects in Vietnam.
Abstract: Integrative teaching methodology is based on
connecting and summarizing knowledge from different subjects in
order to create better understanding of different disciplines and
improvement of competences in general. Integrative teaching
methodology was implemented and realised during one academic
year in 17 Latvian schools according with specially worked out
programme by specialists of different fields for adaptation in social
environment of children and young people with learning, cognitive
functions and motor disorders. Implemented integrative teaching
methodology consisted from three subsections which were
specialised for adaptation in social environment, improvement of
cognitive functions and improvement and harmonization of
personality. The results of investigation showed that the use of
integrative teaching methodology is an effective way for
improvement of learning motivation and negotiation of learning
disorders of different age schoolchildren.
Abstract: The National Bridge Inventory (NBI) includes more
than 600,000 bridges within the United States of America.
Prestressed concrete girder bridges represent one of the most widely
used bridge systems. The majority of these girder bridges were
constructed using 0.5 and 0.6 inch diameter strands. The main
impediments to using larger strand diameters are: 1) lack of prestress
bed capacities, 2) lack of structural knowledge regarding the transfer
and development length of larger strands, and 3) the possibility of
developing wider end zone cracks upon strand release.
This paper presents a study about using 0.7 inch strands in girder
fabrication. Transfer and development length were evaluated, and
girders were fabricated using 0.7 inch strands at different spacings.
Results showed that 0.7 inch strands can be used at 2.0 inch spacing
without violating the AASHTO LRFD Specifications, while attaining
superior performance in shear and flexure.