Abstract: The effects of ethylene (C2H4) feed position and
O2/C2H4 feed molar ratio on ethylene epoxidation in a parallel
dielectric barrier discharge (DBD) were studied. The results showed
that the ethylene feed position fraction of 0.5 and the feed molar
ratio of O2/C2H4 of 0.2:1 gave the highest EO selectivity of 34.3%
and the highest EO yield of 5.28% with low power consumptions of
2.11×10-16 Ws/molecule of ethylene converted and 6.34×10-16
Ws/molecule of EO produced when the DBD system was operated
under the best conditions: an applied voltage of 19 kV, an input
frequency of 500 Hz and a total feed flow rate of 50 cm3/min. The
separate ethylene feed system provided much higher epoxidation
activity as compared to the mixed feed system which gave EO
selectivity of 15.5%, EO yield of 2.1% and the power consumption of
EO produced of 7.7×10-16 Ws/molecule.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation
Abstract: Physiological control of a left ventricle assist device (LVAD) is generally a complicated task due to diverse operating environments and patient variability. In this work, a tracking control algorithm based on sliding mode and feed forward control for a class of discrete-time single input single output (SISO) nonlinear uncertain systems is presented. The controller was developed to track the reference trajectory to a set operating point without inducing suction in the ventricle. The controller regulates the estimated mean pulsatile flow Qp and mean pulsatility index of pump rotational speed PIω that was generated from a model of the assist device. We recall the principle of the sliding mode control theory then we combine the feed-forward control design with the sliding mode control technique to follow the reference trajectory. The uncertainty is replaced by its upper and lower boundary. The controller was tested in a computer simulation covering two scenarios (preload and ventricular contractility). The simulation results prove the effectiveness and the robustness of the proposed controller
Abstract: A new numerical method for solving the twodimensional,
steady, incompressible, viscous flow equations on a
Curvilinear staggered grid is presented in this paper. The proposed
methodology is finite difference based, but essentially takes
advantage of the best features of two well-established numerical
formulations, the finite difference and finite volume methods. Some
weaknesses of the finite difference approach are removed by
exploiting the strengths of the finite volume method. In particular,
the issue of velocity-pressure coupling is dealt with in the proposed
finite difference formulation by developing a pressure correction
equation in a manner similar to the SIMPLE approach commonly
used in finite volume formulations. However, since this is purely a
finite difference formulation, numerical approximation of fluxes is
not required. Results obtained from the present method are based on
the first-order upwind scheme for the convective terms, but the
methodology can easily be modified to accommodate higher order
differencing schemes.
Abstract: A model of a system concerning one species of demersal
(inshore) fish and one of pelagic (offshore) fish undergoing fishing
restricted by marine protected areas is proposed in this paper. This
setup was based on the FISH-BE model applied to the Tabina fishery
in Zamboanga del Sur, Philippines. The components of the model
equations have been adapted from widely-accepted mechanisms in
population dynamics. The model employs Gompertz-s law of growth
and interaction on each type of protected and unprotected subpopulation.
Exchange coefficients between protected and unprotected
areas were assumed to be proportional to the relative area of the
entry region. Fishing harvests were assumed to be proportional to
both the number of fishers and the number of unprotected fish. An
extra term was included for the pelagic population to allow for the
exchange between the unprotected area and the outside environment.
The systems were found to be bounded for all parameter values. The
equations for the steady state were unsolvable analytically but the
existence and uniqueness of non-zero steady states can be proven.
Plots also show that an MPA size yielding the maximum steady state
of the unprotected population can be found. All steady states were
found to be globally asymptotically stable for the entire range of
parameter values.
Abstract: This paper examines the relationship between financial
risks and profitability of the conventional and Islamic banks in
Malaysia for the period between 1996 and 2005. The measures of
profitability that have been used in the study are the return on equity
(ROE) and return on assets (ROA) while the financial risks are credit
risk, interest rate risk and liquidity risks. This study employs panel
data regression analysis of Generalised Least Squares of fixed effects
and random effects models. It was found that credit risk has a
significant impact on ROA and ROE for the conventional as well as
the Islamic banks. The relationship between interest rate risk and ROE
were found to be weakly significant for the conventional banks and
insignificant for the Islamic banks. The effect of interest rate risk on
ROA is significant for the conventional banks. Liquidity risk was
found to have an insignificant impact on both profitability measures.
Abstract: The numerical simulation of the slip effect via
vicoelastic fluid for 4:1 contraction problem is investigated with
regard to kinematic behaviors of streamlines and stress tensor by
models of the Navier-Stokes and Oldroyd-B equations. Twodimensional
spatial reference system of incompressible creeping flow
with and without slip velocity is determined and the finite element
method of a semi-implicit Taylor-Galerkin pressure-correction is
applied to compute the problem of this Cartesian coordinate system
including the schemes of velocity gradient recovery method and the
streamline-Upwind / Petrov-Galerkin procedure. The slip effect at
channel wall is added to calculate after each time step in order to
intend the alteration of flow path. The result of stress values and the
vortices are reduced by the optimum slip coefficient of 0.1 with near
the outcome of analytical solution.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: There is currently intensive debate in Alberta,
Canada, regarding rural to urban water reallocation. This paper
explores the demographic and attitudinal influences that are
associated with the acceptance of water reallocation policies and
whether such acceptance differs between urban and rural residents.
We investigate three policy orientations in regards to water policies:
i) government intervention; ii) environmental protection; and iii)
protecting irrigators- water rights. We find that urban dwellers are
more likely to favour government intervention while rural dwellers
are more likely to support policies that aim at protecting irrigators-
water rights. While urban dwellers are also more likely to favour
environmental protection, the difference is not statistically
significant. We also find that other factors have a significant impact
on policy choice irrespective of residence such as demographic and
socioeconomic factors as well as the values people hold toward water
and the environment.
Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: Sustainable energy usage has been recognized as one
of the important measure to increase the competitiveness of the
nation globally. Many strong emphases were given in the Ninth
Malaysia Plan (RMK9) to improve energy efficient especially to
government buildings. With this in view, a project to investigate the
potential of energy saving in selected building in Universiti Tun
Hussein Onn Malaysia (UTHM) was carried out. In this project, a
case study involving electric energy consumption of the academic
staff office building was conducted. The scope of the study include to
identify energy consumption in a selected building, to study energy
saving opportunities, to analyse cost investment in term of economic
and to identify users attitude with respect to energy usage. The
MS1525:2001, Malaysian Standard -Code of practice on energy
efficiency and use of renewable energy for non-residential buildings
was used as reference. Several energy efficient measures were
considered and their merits and priority were compared. Improving
human behavior can reduce energy consumption by 6% while
technical measure can reduce energy consumption by 44%. Two
economic analysis evaluation methods were applied; they are the
payback period method and net present value method.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: Automatic keyphrase extraction is useful in efficiently
locating specific documents in online databases. While several
techniques have been introduced over the years, improvement on
accuracy rate is minimal. This research examines attribute scores for
author-supplied keyphrases to better understand how the scores affect
the accuracy rate of automatic keyphrase extraction. Five attributes
are chosen for examination: Term Frequency, First Occurrence, Last
Occurrence, Phrase Position in Sentences, and Term Cohesion
Degree. The results show that First Occurrence is the most reliable
attribute. Term Frequency, Last Occurrence and Term Cohesion
Degree display a wide range of variation but are still usable with
suggested tweaks. Only Phrase Position in Sentences shows a totally
unpredictable pattern. The results imply that the commonly used
ranking approach which directly extracts top ranked potential phrases
from candidate keyphrase list as the keyphrases may not be reliable.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: In this study it is aimed to determine the level of preservice teachers- computer phobia. Whether or not computer phobia meaningfully varies statistically according to gender and computer experience has been tested in the study. The study was performed on 430 pre-service teachers at the Education Faculty in Rize/Turkey. Data in the study were collected through the Computer Phobia Scale consisting of the “Personal Knowledge Questionnaire", “Computer Anxiety Rating Scale", and “Computer Thought Survey". In this study, data were analyzed with statistical processes such as t test, and correlation analysis. According to results of statistical analyses, computer phobia of male pre-service teachers does not statistically vary depending on their gender. Although male preservice teachers have higher computer anxiety scores, they have lower computer thought scores. It was also observed that there is a negative and intensive relation between computer experience and computer anxiety. Meanwhile it was found out that pre-service teachers using computer regularly indicated lower computer anxiety. Obtained results were tried to be discussed in terms of the number of computer classes in the Education Faculty curriculum, hours of computer class and the computer availability of student teachers.
Abstract: This research aimed to study the market feasibility for
new brand coffee house, the case study of Thailand.. This study is a
mixed methods research combining quantitative research and the
qualitative research. Primary data 350 sets of questionnaires were
distributed, and the high quality completed questionnaires of 320 sets
returned. Research samples are identified as customers’ of Hi-end
department stores in Thailand. The sources of secondary data were
critical selected from highly reliable sources, both from public and
private sectors. The results were used to classify the customer group
into two main groups, the younger than 25 and the older than 25years
old. Results of the younger group, are give priority to the dimension
of coffee house and its services dimension more than others, then
branding dimension and the product dimension respectively. On the
other hand, the older group give the difference result as they rate the
important of the branding, coffee house and its services, then the
product respectively. Coffee consuming is not just the trend but it
has become part of people lifestyle. And the new cultures also created
by the wise businessman. Coffee was long produced and consumed in
Thailand. But it is surprisingly the hi-end brand coffee houses in Thai
market are mostly imported brands. The café business possibility for
Thai brand coffee house in Thai market were discussed in the paper.
Abstract: In this paper we use data mining techniques to investigate factors that contribute significantly to enhancing the risk of acute coronary syndrome. We assume that the dependent variable is diagnosis – with dichotomous values showing presence or absence of disease. We have applied binary regression to the factors affecting the dependent variable. The data set has been taken from two different cardiac hospitals of Karachi, Pakistan. We have total sixteen variables out of which one is assumed dependent and other 15 are independent variables. For better performance of the regression model in predicting acute coronary syndrome, data reduction techniques like principle component analysis is applied. Based on results of data reduction, we have considered only 14 out of sixteen factors.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential