Abstract: The paper is concerned with the technological process of renovation of shafts used in industrial manufacturing for extruding of sheet material. In the classical renovation technologies, a chrome based coating is applied to the working surface of the shaft in galvanic baths. The process, however, is known to be exclusively harmful due to the waste cyanide products. In this work, we present an advanced nanotechnology based on nonelectric chemical laying of a nickel coating with included nanoparticles. The technology is environmentally harmless and the new coating features an increased hardness and wear resistance. Results from experimental tests of the nanostructured nickel coating are presented and discussed.
Abstract: In order to avoid the potentially devastating
consequences of global warming and climate change, the carbon
dioxide “CO2" emissions caused due to anthropogenic activities must
be reduced considerably. This paper presents the first study
examining the feasibility of carbon sequestration in construction and
demolition “C&D" waste. Experiments were carried out in a self
fabricated Batch Reactor at 40ºC, relative humidity of 50-70%, and
flow rate of CO2 at 10L/min for 1 hour for water-to-solids ratio of 0.2
to 1.2. The effect of surface area was found by comparing the
theoretical extent of carbonation of two different sieve sizes (0.3mm
and 2.36mm) of C&D waste. A 38.44% of the theoretical extent of
carbonation equating to 4% CO2 sequestration extent was obtained
for C&D waste sample for 0.3mm sieve size. Qualitative,
quantitative and morphological analyses were done to validate
carbonate formation using X-ray diffraction “X.R.D.," thermal
gravimetric analysis “T.G.A., “X-Ray Fluorescence Spectroscopy
“X.R.F.," and scanning electron microscopy “S.E.M".
Abstract: This work presents a study on the abrasive water jet
(AWJ) machining. An explicit finite element analysis (FEA) of
single abrasive particle impact on stainless steel 1.4304 (AISI 304) is
conducted. The abrasive water jet machining is modeled by FEA
software ABAQUS/CAE. Shapes of craters in FEM simulation
results were used and compared with the previous experimental and
FEM works by means of crater sphericity. The influence of impact
angle and particle velocity was observed. Adaptive mesh domain is
used to model the impact zone. Results are in good agreement with
those obtained from the experimental and FEM simulation. The
crater-s depth is also obtained for different impact angle and abrasive
particle velocities.
Abstract: This paper proposes an algorithm which automatically aligns and stitches the component medical images (fluoroscopic) with varying degrees of overlap into a single composite image. The alignment method is based on similarity measure between the component images. As applied here the technique is intensity based rather than feature based. It works well in domains where feature based methods have difficulty, yet more robust than traditional correlation. Component images are stitched together using the new triangular averaging based blending algorithm. The quality of the resultant image is tested for photometric inconsistencies and geometric misalignments. This method cannot correct rotational, scale and perspective artifacts.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: Internet Protocol version 4 (IPv4) address is decreasing and a rapid transition method to the next generation IP address (IPv6) should be established. This study aims to evaluate and select the best performance of the IPv6 address network transitionmechanisms, such as IPv4/IPv6 dual stack, transport Relay Translation (TRT) and Reverse Proxy with additional features. It is also aim to prove that faster access can be done while ensuring optimal usage of available resources used during the test and actual implementation. This study used two test methods such asInternet Control Message Protocol (ICMP)ping and ApacheBenchmark (AB) methodsto evaluate the performance.Performance metrics for this study include aspects ofaverageaccessin one second,time takenfor singleaccess,thedata transfer speed and the costof additional requirements.Reverse Proxy with Caching featureis the most efficientmechanism because of it simpler configurationandthe best performerfrom the test conducted.
Abstract: The Address Resolution Protocol (ARP) is used by
computers to map logical addresses (IP) to physical addresses
(MAC). However ARP is an all trusting protocol and is stateless
which makes it vulnerable to many ARP cache poisoning attacks
such as Man-in-the-Middle (MITM) and Denial of service (DoS)
attacks. These flaws result in security breaches thus weakening the
appeal of the computer for exchange of sensitive data. In this paper
we describe ARP, outline several possible ARP cache poisoning
attacks and give the detailed of some attack scenarios in network
having both wired and wireless hosts. We have analyzed each of
proposed solutions, identify their strengths and limitations. Finally
get that no solution offers a feasible solution. Hence, this paper
presents an efficient and secure version of ARP that is able to cope
up with all these types of attacks and is also a feasible solution. It is a
stateful protocol, by storing the information of the Request frame in
the ARP cache, to reduce the chances of various types of attacks in
ARP. It is more efficient and secure by broadcasting ARP Reply
frame in the network and storing related entries in the ARP cache
each time when communication take place.
Abstract: Geometric design is an important part of planning
process design for physical highway to fill up basic function of roads,
to give good traffic service. It is found that most of the road safety
problems occur at the horizontal curves and complex-compound
curves. In this paper, review on Sagarinn-Myinsain Portion of Nay
Pyi Taw - Mandalay highway has been conducted in aspect of
geometric design induced road safety condition. Horizontal
alignment of geometric features and curve details are reviewed based
on (AASHTO) standard and revised by Autodesk Land Desktop
Software. Moreover, 85th Percentile Operation Speeds (V85) with
driver confidence on horizontal curves is evaluated in order to obtain
the range of highway safety factor (FS). The length of the selected
highway portion is 13.65 miles and 8 lanes. The results of this study
can be used to investigate the possible hazardous locations in
advance and to revise how design radius and super elevation should
be for better road safety performance for the selected portion.
Moreover, the relationship between highway safety and highway
geometry characteristics can also be known.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually to some extent the effects of blurred edges and jagged artifacts in the image. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to enhance edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (''jaggies'') along the tangent directions. In order to preserve image features such as edges, angles and textures, the nonlinear diffusion coefficients are locally adjusted according to the first and second order directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: This paper investigates the problem of automated defect
detection for textile fabrics and proposes a new optimal filter design
method to solve this problem. Gabor Wavelet Network (GWN) is
chosen as the major technique to extract the texture features from
textile fabrics. Based on the features extracted, an optimal Gabor filter
can be designed. In view of this optimal filter, a new semi-supervised
defect detection scheme is proposed, which consists of one real-valued
Gabor filter and one smoothing filter. The performance of the scheme
is evaluated by using an offline test database with 78 homogeneous
textile images. The test results exhibit accurate defect detection with
low false alarm, thus showing the effectiveness and robustness of the
proposed scheme. To evaluate the detection scheme comprehensively,
a prototyped detection system is developed to conduct a real time test.
The experiment results obtained confirm the efficiency and
effectiveness of the proposed detection scheme.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: In this study, the problem of discriminating between interictal epileptic and non- epileptic pathological EEG cases, which present episodic loss of consciousness, investigated. We verify the accuracy of the feature extraction method of autocross-correlated coefficients which extracted and studied in previous study. For this purpose we used in one hand a suitable constructed artificial supervised LVQ1 neural network and in other a cross-correlation technique. To enforce the above verification we used a statistical procedure which based on a chi- square control. The classification and the statistical results showed that the proposed feature extraction is a significant accurate method for diagnostic discrimination cases between interictal and non-interictal EEG events and specifically the classification procedure showed that the LVQ neural method is superior than the cross-correlation one.
Abstract: Over the past several years, there has been a
considerable amount of research within the field of Quality of
Service (QoS) support for distributed multimedia systems. One of the
key issues in providing end-to-end QoS guarantees in packet
networks is determining a feasible path that satisfies a number of
QoS constraints. The problem of finding a feasible path is NPComplete
if number of constraints is more than two and cannot be
exactly solved in polynomial time. We proposed Feasible Path
Selection Algorithm (FPSA) that addresses issues with pertain to
finding a feasible path subject to delay and cost constraints and it
offers higher success rate in finding feasible paths.
Abstract: This paper presents an on-going research work on the
implementation of feature-based machining via macro programming.
Repetitive machining features such as holes, slots, pockets etc can
readily be encapsulated in macros. Each macro consists of methods
on how to machine the shape as defined by the feature. The macro
programming technique comprises of a main program and
subprograms. The main program allows user to select several
subprograms that contain features and define their important
parameters. With macros, complex machining routines can be
implemented easily and no post processor is required. A case study
on machining of a part that comprised of planar face, hole and pocket
features using the macro programming technique was carried out. It
is envisaged that the macro programming technique can be extended
to other feature-based machining fields such as the newly developed
STEP-NC domain.
Abstract: We develop a new interface for Bus-Net which is
optimized for a smartphone. We are continuing to develop the shortest
path planning system of public transportation called "Bus-Net" in
Tottori prefecture as web application to improve the usability of
public transportation. Recent trend of computing platform, however
has shifted to an advanced mobile device called a smartphone such as
iPhone and Android in Japan. A smartphone has different characters
with existing feature phone in terms of OS, large touche panel, and
several other features. We derive a guideline to design the new interface
for a smartphone to full use of the functionality. The guideline is
about simplicity of user-s operation, location awareness and usability.
We developed the new interface for “Bus-Net" on iPhone referring
to the guideline. Due to the evaluation, the application interface we
developed is better than the existing web-based interface in terms of
the usability.
Abstract: This paper aims to propose a novel, robust, and simple method for obtaining a human 3D face model and camera pose (position and orientation) from a video sequence. Given a video sequence of a face recorded from an off-the-shelf digital camera, feature points used to define facial parts are tracked using the Active- Appearance Model (AAM). Then, the face-s 3D structure and camera pose of each video frame can be simultaneously calculated from the obtained point correspondences. This proposed method is primarily based on the combined approaches of Gradient Descent and Powell-s Multidimensional Minimization. Using this proposed method, temporarily occluded point including the case of self-occlusion does not pose a problem. As long as the point correspondences displayed in the video sequence have enough parallax, these missing points can still be reconstructed.
Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.
Abstract: In the present study, a support vector machine (SVM) learning approach to character recognition is proposed. Simple
feature detectors, similar to those found in the human visual system, were used in the SVM classifier. Alphabetic characters were rotated
to 8 different angles and using the proposed cognitive model, all characters were recognized with 100% accuracy and specificity.
These same results were found in psychiatric studies of human character recognition.
Abstract: With increasing data in medical databases, medical
data retrieval is growing in popularity. Some of this analysis
including inducing propositional rules from databases using many
soft techniques, and then using these rules in an expert system.
Diagnostic rules and information on features are extracted from
clinical databases on diseases of congenital anomaly. This paper
explain the latest soft computing techniques and some of the
adaptive techniques encompasses an extensive group of methods
that have been applied in the medical domain and that are used for
the discovery of data dependencies, importance of features,
patterns in sample data, and feature space dimensionality
reduction. These approaches pave the way for new and interesting
avenues of research in medical imaging and represent an important
challenge for researchers.
Abstract: A set of Artificial Neural Network (ANN) based methods
for the design of an effective system of speech recognition of
numerals of Assamese language captured under varied recording
conditions and moods is presented here. The work is related to
the formulation of several ANN models configured to use Linear
Predictive Code (LPC), Principal Component Analysis (PCA) and
other features to tackle mood and gender variations uttering numbers
as part of an Automatic Speech Recognition (ASR) system in
Assamese. The ANN models are designed using a combination of
Self Organizing Map (SOM) and Multi Layer Perceptron (MLP)
constituting a Learning Vector Quantization (LVQ) block trained in a
cooperative environment to handle male and female speech samples
of numerals of Assamese- a language spoken by a sizable population
in the North-Eastern part of India. The work provides a comparative
evaluation of several such combinations while subjected to handle
speech samples with gender based differences captured by a microphone
in four different conditions viz. noiseless, noise mixed, stressed
and stress-free.