Abstract: The mechanical properties of granular solids are
dependent on the flow of stresses from one particle to another
through inter-particle contact. Although some experimental methods
have been used to study the inter-particle contacts in the past,
preliminary work with these techniques indicated that they do not
have the necessary resolution to distinguish between those contacts
that transmit the load and those that do not, especially for systems
with a wide distribution of particle sizes. In this research, computer
simulations are used to study the nature and distribution of contacts
in a compact with wide particle size distribution, representative of
aggregate size distribution used in asphalt pavement construction.
The packing fraction, the mean number of contacts and the
distribution of contacts were studied for different scenarios. A
methodology to distinguish and compute the fraction of load-bearing
particles and the fraction of space-filling particles (particles that do
not transmit any force) is needed for further investigation.
Abstract: Few decades ago, electronic and sensor technologies
are merged into vehicles as the Advanced Driver Assistance
System(ADAS). However, sensor-based ADASs have limitations
about weather interference and a line-of-sight nature problem. In our
project, we investigate a Relative Position based ADAS(RP-ADAS).
We divide the RP-ADAS into four main research areas: GNSS,
VANET, Security/Privacy, and Application. In this paper, we research
the GNSS technologies and determine the most appropriate one. With
the performance evaluation, we figure out that the C/A code based
GPS technologies are inappropriate for 'which lane-level' application.
However, they can be used as a 'which road-level' application.
Abstract: This study was conducted published to investigate
there liability of the equation pressure-impulse (PI) reinforced
concrete column inprevious studies. Equation involves three different
levels of damage criteria known as D =0. 2, D =0. 5 and D =0. 8.The
damage criteria known as a minor when 0-0.2, 0.2-0.5is known as
moderate damage, high damage known as 0.5-0.8, and 0.8-1 of the
structure is considered a failure. In this study, two types of reliability
analyzes conducted. First, using pressure-impulse equation with
different parameters. The parameters involved are the concrete
strength, depth, width, and height column, the ratio of longitudinal
reinforcement and transverse reinforcement ratio. In the first analysis
of the reliability of this new equation is derived to improve the
previous equations. The second reliability analysis involves three
types of columns used to derive the PI curve diagram using the
derived equation to compare with the equation derived from other
researchers and graph minimum standoff versus weapon yield
Federal Emergency Management Agency (FEMA). The results
showed that the derived equation is more accurate with FEMA
standards than previous researchers.
Abstract: Type 2 diabetes mellitus (T2DM) is a complex
metabolic disorder that characterized by the presence of high glucose
in blood that cause from insulin resistance and insufficiency due to
deterioration β-cell Langerhans functions. T2DM is commonly
caused by the combination of inherited genetic variations as well as
our own lifestyle. Metallothionein (MT) is a known cysteine-rich
protein responsible in helping zinc homeostasis which is important in
insulin signaling and secretion as well as protection our body from
reactive oxygen species (ROS). MT scavenged ROS and free
radicals in our body happen to be one of the reasons of T2DM and its
complications. The objective of this study was to investigate the
association of MT1A and MT2A polymorphisms between T2DM and
control subjects among Malay populations. This study involved 150
T2DM and 120 Healthy individuals of Malay ethnic with mixed
genders. The genomic DNA was extracted from buccal cells and
amplified for MT1A and MT2A loci; the 347bp and 238bp banding
patterns were respectively produced by mean of the Polymerase
Chain Reaction (PCR). The PCR products were digested with Mlucl
and Tsp451 restriction enzymes respectively and producing
fragments lengths of (158/189/347bp) and (103/135/238bp)
respectively. The ANOVA test was conducted and it shown that there
was a significant difference between diabetic and control subjects for
age, BMI, WHR, SBP, FPG, HBA1C, LDL, TG, TC and family
history with (P0.05). The genotype
frequency for AA, AG and GG of MT1A polymorphisms was 72.7%,
22.7% and 4.7% in cases and 15%, 55% and 30% in control
respectively. As for MT2A, genotype frequency of GG, GC and CC
was 42.7%, 27.3% and 30% in case and 5%, 40% and 55% for
control respectively. Both polymorphisms show significant difference
between two investigated groups with (P=0.000). The Post hoc test
was conducted and shows a significant difference between the
genotypes within each polymorphism (P=0. 000). The MT1A and
MT2A polymorphisms were believed to be the reliable molecular
markers to distinguish the T2DM subjects from healthy individuals in
Malay populations.
Abstract: Cameras are often mounted on platforms that canmove like rovers, booms, gantries and aircraft. People operate suchplatforms to capture desired views of scene or target. To avoidcollisions with the environment and occlusions, such platforms oftenpossess redundant degrees-of-freedom. As a result, manipulatingsuch platforms demands much skill. Visual-servoing some degrees-of-freedom may reduce operator burden and improve tracking per-formance. This concept, which we call human-in-the-loop visual-servoing, is demonstrated in this paper and applies a Α-β-γ filter and feedforward controller to a broadcast camera boom.
Abstract: It has been established that microRNAs (miRNAs) play
an important role in gene expression by post-transcriptional regulation
of messengerRNAs (mRNAs). However, the precise relationships
between microRNAs and their target genes in sense of numbers,
types and biological relevance remain largely unclear. Dissecting the
miRNA-target relationships will render more insights for miRNA
targets identification and validation therefore promote the understanding
of miRNA function. In miRBase, miRanda is the key
algorithm used for target prediction for Zebrafish. This algorithm
is high-throughput but brings lots of false positives (noise). Since
validation of a large scale of targets through laboratory experiments
is very time consuming, several computational methods for miRNA
targets validation should be developed. In this paper, we present an
integrative method to investigate several aspects of the relationships
between miRNAs and their targets with the final purpose of extracting
high confident targets from miRanda predicted targets pool. This is
achieved by using the techniques ranging from statistical tests to
clustering and association rules. Our research focuses on Zebrafish.
It was found that validated targets do not necessarily associate with
the highest sequence matching. Besides, for some miRNA families,
the frequency of their predicted targets is significantly higher in the
genomic region nearby their own physical location. Finally, in a case
study of dre-miR-10 and dre-miR-196, it was found that the predicted
target genes hoxd13a, hoxd11a, hoxd10a and hoxc4a of dre-miR-
10 while hoxa9a, hoxc8a and hoxa13a of dre-miR-196 have similar
characteristics as validated target genes and therefore represent high
confidence target candidates.
Abstract: With increasing utilization of the wireless devices in
different fields such as medical devices and industrial fields, the
paper presents a method for simplify the Bluetooth packets with
throughput enhancing. The paper studies a vital issue in wireless
communications, which is the throughput of data over wireless
networks. In fact, the Bluetooth and ZigBee are a Wireless Personal
Area Network (WPAN). With taking these two systems competition
consideration, the paper proposes different schemes for improve the
throughput of Bluetooth network over a reliable channel. The
proposition depends on the Channel Quality Driven Data Rate
(CQDDR) rules, which determines the suitable packet in the
transmission process according to the channel conditions. The
proposed packet is studied over additive White Gaussian Noise
(AWGN) and fading channels. The Experimental results reveal the
capability of extension of the PL length by 8, 16, 24 bytes for classic
and EDR packets, respectively. Also, the proposed method is suitable
for the low throughput Bluetooth.
Abstract: Forming a legal culture among citizens is a
complicated and lengthy process, influencing all spheres of social
life. It includes promoting justice, learning rights and duties, the
introduction of juridical norms and knowledge, and also a process of
developing a system of legal acts and constitutional norms. Currently,
the evaluative and emotional influence of attempts to establish a legal
culture among the citizens of Kazakhstan is limited by real legal
practice. As a result, the values essential to a sound civil society are
absent from the consciousness of the Kazakh people who are thus, in
turn, not able to develop respect for these values. One of the
disadvantages of the modern Kazakh educational system is a
tendency to underrate the actual forces shaping the worldview of
Kazakh youths. The mass-media, which are going through a
personnel crisis, cannot provide society with the legal and political
information necessary to form the sort of legal culture required for a
true civil society.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: Proximate (moisture, protein, total fat, total ash) and mineral (K, P, Na, Mg, Ca, Zn, Fe, Cu and Mn) composition of chicken giblets (heart, liver and gizzard) were investigated. Phosphorous content, as well as proximate composition, were determined according to recommended ISO methods. The content of all elements, except phosphorus, of the giblets tissues were determined using inductively coupled plasma-optical emission spectrometry (ICP-OES), after dry ashing mineralization. Regarding proximate composition heart was the highest in total fat content, and the lowest in protein content. Liver was the highest in protein and total ash content, while gizzard was the highest in moisture and the lowest in total fat content. Regarding mineral composition liver was the highest for K, P, Ca, Mg, Fe, Zn, Cu, and Mn, while heart was the highest for Na content. The contents of almost all investigated minerals in analysed giblets tissues of chickens from Vojvodina were similar to values reported in the literature, i.e. in national food composition databases of other countries.
Abstract: In the multi objective optimization, in the case when generated set of Pareto optimal solutions is large, occurs the problem to select of the best solution from this set. In this paper, is suggested a method to order of Pareto set. Ordering the Pareto optimal set carried out in conformity with the introduced distance function between each solution and selected reference point, where the reference point may be adjusted to represent the preferences of a decision making agent. Preference information about objective weights from a decision maker may be expressed imprecisely. The developed elicitation procedure provides an opportunity to obtain surrogate numerical weights for the objectives, and thus, to manage impreciseness of preference. The proposed method is a scalable to many objectives and can be used independently or as complementary to the various visualization techniques in the multidimensional case.
Abstract: The use of Electronic Commerce (EC)
technologies enables Small Medium Enterprises (SMEs) to improve their efficiency and competitive position. Much of the literature proposes an extensive set of benefits for
organizations that choose to adopt and implement ECommerce
systems. Factors of Business –to-business (B2B)
E-Commerce adoption and implementation have been
extensively investigated. Despite enormous attention given to encourage Small Medium Enterprises (SMEs) to adopt and
implement E-Commerce, little research has been carried out in identifying the factors of Business-to-Consumer ECommerce adoption and implementation for SMEs. To conduct the study, Tornatsky and Fleischer model was adopted
and tested in four SMEs located in Christchurch, New
Zealand. This paper explores the factors that impact the
decision and method of adoption and implementation of ECommerce
systems in automobile industry. Automobile
industry was chosen because the product they deal with i.e.
cars are not a common commodity to be sold online, despite this fact the eCommerce penetration in automobile industry is
high. The factors that promote adoption and implementation of
E-Commerce technologies are discussed, together with the
barriers. This study will help SME owners to effectively
handle the adoption and implementation process and will also
improve the chance of successful E-Commerce
implementation. The implications of the findings for
managers, consultants, and government organizations engaged in promoting E-Commerce adoption and implementation in
small businesses and future research are discussed.
Abstract: An experiment was conducted with 80 unsexed
broilers of the Arbor Acress strain to determine the capability of a
carrot and fruit juice wastes mixture (carrot, apple, manggo, avocado,
orange, melon and Dutch egg plant) in the same proportion for
replacing corn in broiler diet. This study involved a completely
randomized design (CRD) with 5 treatments (0, 5, 10, 15, and 20% of
juice wastes mixture in diets) and 4 replicates per treatment. Diets
were isonitrogenous (22% crude protein) and isocaloric (3000 kcal/kg
diet). Measured variables were feed consumption, average daily
gain, feed conversion, as well as percentages of abdominal fat pad,
carcass, digestive organs (liver, pancreas and gizzard), and heart.
Data were analyzed by analysis of variance for CRD. Increasing
juice wastes mixture levels in diets increased feed consumption
(P
Abstract: The paper proposes a novel technique for iris
recognition using texture and phase features. Texture features are
extracted on the normalized iris strip using Haar Wavelet while phase
features are obtained using LOG Gabor Wavelet. The matching
scores generated from individual modules are combined using sum of
score technique. The system is tested on database obtained from Bath
University and Indian Institute of Technology Kanpur and is giving
an accuracy of 95.62% and 97.66% respectively. The FAR and FRR
of the combined system is also reduced comparatively.
Abstract: The objective of this work is to show a procedure for
mesh generation in a fluidized bed using large eddy simulations
(LES) of a filtered two-fluid model. The experimental data were
obtained by [1] in a laboratory fluidized bed. Results show that it is
possible to use mesh with less cells as compared to RANS turbulence
model with granular kinetic theory flow (KTGF). Also, the numerical
results validate the experimental data near wall of the bed, which
cannot be predicted by RANS.model.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Abstract: As emails communications have no consistent
authentication procedure to ensure the authenticity, we present an
investigation analysis approach for detecting forged emails based on
Random Forests and Naïve Bays classifiers. Instead of investigating
the email headers, we use the body content to extract a unique writing
style for all the possible suspects. Our approach consists of four main
steps: (1) The cybercrime investigator extract different effective
features including structural, lexical, linguistic, and syntactic
evidence from previous emails for all the possible suspects, (2) The
extracted features vectors are normalized to increase the accuracy
rate. (3) The normalized features are then used to train the learning
engine, (4) upon receiving the anonymous email (M); we apply the
feature extraction process to produce a feature vector. Finally, using
the machine learning classifiers the email is assigned to one of the
suspects- whose writing style closely matches M. Experimental
results on real data sets show the improved performance of the
proposed method and the ability of identifying the authors with a
very limited number of features.
Abstract: Stability of functionally graded beams with piezoelectric layers subjected to axial compressive load that is simply supported at both ends is studied in this paper. The displacement field of beam is assumed based on first order shear deformation beam theory. Applying the Hamilton's principle, the governing equation is established. The influences of applied voltage, dimensionless geometrical parameter, functionally graded index and piezoelectric thickness on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study is carried out with a known data.