Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: This entry concerned with dense silica bricks
microstructure was produced as a part of a project within the
Technology Agency of the Czech Republic which is being
implemented in cooperation of the biggest producer of refractories
the P-D Refractories CZ company with the research organisation
Brno University of Technology. The paper is focused on the
influence of mixture homogenisation and the influence of grain size
of the mineraliser on the resulting utility properties of the material as
well as its microstructure. It has a decisive influence on the durability
of the material in a building structure. This paper is a continuation of
a previously published study dealing with the suitability of various
types of mineralising agents in terms of density, strength and mineral
composition of silica brick.
The entry describes the influence of the method of mixture
homogenisation and the influence of granulometry of the applied Femineralising
agent on the resulting silica microstructure. Porosity,
density, phase composition and microstructure of the experimentally
prepared silica bricks samples were examined and the results were
discussed in context with the technology of homogenisation and
firing temperature used. The properties of silica bricks samples were
compared to the sample without any Fe-mineraliser.
Abstract: Nanotechnology is the new cyber, according to several major leaders in this field. Just as cyber is entrenched across global society now, nano is poised to be major capabilities enabler of the next decades. Expert members from the National Nanotechnology Initiative (in U.S.) representing government and science disciplines say nano has great significance for the military and the general public. It is predicted that after next 15 years nanotechnology will replace information technology as the most economic technology platform. Nanotechnology has even wider applications than information technology.
Abstract: The reduction of greenhouse gases emissions is highly
discussed ecological theme at present. In addition to power industry
also main production sectors of binders, i.e. cement, air and hydraulic
lime are very sensitive to these questions. One of the possibilities
how CO2 emissions can be reduced directly at clinker burnout is
represented by partial substitution of lime with a material containing
limy ions at absence of carbonate group. Fluidised fly ash is one of
such potential raw materials where CaO can be found free and also
bound in anhydrite, CaSO4. At application of FBC (fluidized bed
combustion) fly ash with approximate 20% CaO content and its
dosing ratio to high percent lime 1:2, corresponding stechiometrically
to the preparation of raw material powder, approximately 0,37 t CO2
per 1 ton of one-component cement would be released at clinker
burnout compared to 0,46 t CO2 when orthodox raw materials are
used. The reduction of CO2 emissions thus could reach even 20%.
Abstract: Audio-lingual Method (ALM) is a teaching approach
that is claimed that ineffective for teaching second/foreign languages.
Because some linguists and second/foreign language teachers believe
that ALM is a rote learning style. However, this study is done on a
belief that ALM will be able to solve Thais’ English speaking
problem. This paper aims to report the findings on teaching English
speaking to adult learners with an “adapted ALM”, one distinction of
which is to use Thai as the medium language of instruction.
The participants are consisted of 9 adult learners. They were
allowed to speak English more freely using both the materials
presented in the class and their background knowledge of English. At
the end of the course, they spoke English more fluently, more
confidently, to the extent that they applied what they learnt both in
and outside the class.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: In this study, a three dimensional numerical heat
transfer model has been used to simulate the laser structuring of
polymer substrate material in the Three-Dimensional Molded
Interconnect Device (3D MID) which is used in the advanced multifunctional
applications. A finite element method (FEM) transient
thermal analysis is performed using APDL (ANSYS Parametric
Design Language) provided by ANSYS. In this model, the effect of
surface heat source was modeled with Gaussian distribution, also the
effect of the mixed boundary conditions which consist of convection
and radiation heat transfers have been considered in this analysis. The
model provides a full description of the temperature distribution, as
well as calculates the depth and the width of the groove upon material
removal at different set of laser parameters such as laser power and
laser speed. This study also includes the experimental procedure to
study the effect of laser parameters on the depth and width of the
removal groove metal as verification to the modeled results. Good
agreement between the experimental and the model results is
achieved for a wide range of laser powers. It is found that the quality
of the laser structure process is affected by the laser scan speed and
laser power. For a high laser structured quality, it is suggested to use
laser with high speed and moderate to high laser power.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: This research paper aims to identify, analyze and rank
factors affecting labor productivity in Spain with respect to their
relative importance. Using a selected set of 35 factors, a structured
questionnaire survey was utilized as the method to collect data from
companies. Target population is comprised by a random
representative sample of practitioners related with the Spanish
construction industry. Findings reveal the top five ranked factors are
as follows: (1) shortage or late supply of materials; (2) clarity of the
drawings and project documents; (3) clear and daily task assignment;
(4) tools or equipment shortages; (5) level of skill and experience of
laborers. Additionally, this research also pretends to provide simple
and comprehensive recommendations so that they could be
implemented by construction managers for an effective management
of construction labor forces.
Abstract: Currently, biological control programs in greenhouse
crops involve the use, at the same time, several natural enemies
during the crop cycle. Also, large number of plant species grown in
greenhouses, among them, the used cultivars are also wide. However,
the cultivar effects on entomophagous species efficacy (predators and
parasitoids) have been scarcely studied. A new method had been
developed, using the factitious prey or host Ephestia kuehniella. It
allow us to evaluate, under greenhouse or controlled conditions
(semi-field), the cultivar effects on the entomophagous species
effectiveness. The work was carried out in greenhouse tomato crop. It
has been found the biological and ecological activities of predatory
species (Nesidiocoris tenuis) and egg-parasitoid (Trichogramma
achaeae) can be well represented with the use of the factitious prey
or host; being better in the former than the latter. The data found in
the trial are shown and discussed. The developed method could be
applied to evaluate new plant materials before making available to
farmers as commercial varieties, at low costs and easy use.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: One of the most important tasks in urban remote
sensing is the detection of impervious surfaces (IS), such as roofs and
roads. However, detection of IS in heterogeneous areas still remains
one of the most challenging tasks. In this study, detection of concrete
roof using an object-based approach was proposed. A new rule-based
classification was developed to detect concrete roof tile. This
proposed rule-based classification was applied to WorldView-2
image and results showed that the proposed rule has good potential to
predict concrete roof material from WorldView-2 images, with 85%
accuracy.
Abstract: The article presents the trends in Georgian wine
market development and evaluates the competitive advantages of
Georgia to enter the wine market based on its customs, traditions and
historical practices combined with modern technologies.
In order to analyze the supply of wine, dynamics of vineyard land
area and grape varieties are discussed, trends in wine production are
presented, trends in export and import are evaluated, local wine
market, its micro and macro environments are studied and analyzed
based on the interviews with experts and analysis of initial recording
materials.
For strengthening its position on the international market, the level
of competitiveness of Georgian wine is defined, which is evaluated
by “ex-ante” and “ex-post” methods, as well as by four basic and two
additional factors of the Porter’s diamond method; potential
advantages and disadvantages of Georgian wine are revealed.
Conclusions are made by identifying the factors that hinder the
development of Georgian wine market. Based on the conclusions,
relevant recommendations are developed.
Abstract: Boron-gypsum is a waste which occurs in the boric
acid production process. In this study, the boron content of this waste
is evaluated for the use in synthesis of magnesium borates and such
evaluation of this kind of waste is useful more than storage or
disposal. Magnesium borates, which are a sub-class of boron
minerals, are useful additive materials for the industries due to their
remarkable thermal and mechanical properties. Magnesium borates
were obtained hydrothermally at different temperatures. Novelty of
this study is the search of the solution density effects to magnesium
borate synthesis process for the increasing the possibility of borongypsum
usage as a raw material. After the synthesis process, products
are subjected to XRD and FT-IR to identify and characterize their
crystal structure, respectively.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: Thermal insulation materials based on natural fibers
represent a very promising area of materials based on natural easy
renewable row sources. These materials may be in terms of the
properties of most competing synthetic insulations, but show
somewhat higher moisture sensitivity and thermal insulation
properties are strongly influenced by the density and orientation of
fibers. The paper described the problem of hygrothermal behavior of
thermal insulation materials based on natural plant and animal fibers.
This is especially the dependence of the thermal properties of these
materials on the type of fiber, bulk density, temperature, moisture and
the fiber orientation.
Abstract: Artificial Neural Networks (ANN) trained using backpropagation
(BP) algorithm are commonly used for modeling
material behavior associated with non-linear, complex or unknown
interactions among the material constituents. Despite multidisciplinary
applications of back-propagation neural networks
(BPNN), the BP algorithm possesses the inherent drawback of
getting trapped in local minima and slowly converging to a global
optimum. The paper present a hybrid artificial neural networks and
genetic algorithm approach for modeling slump of ready mix
concrete based on its design mix constituents. Genetic algorithms
(GA) global search is employed for evolving the initial weights and
biases for training of neural networks, which are further fine tuned
using the BP algorithm. The study showed that, hybrid ANN-GA
model provided consistent predictions in comparison to commonly
used BPNN model. In comparison to BPNN model, the hybrid ANNGA
model was able to reach the desired performance goal quickly.
Apart from the modeling slump of ready mix concrete, the synaptic
weights of neural networks were harnessed for analyzing the relative
importance of concrete design mix constituents on the slump value.
The sand and water constituents of the concrete design mix were
found to exhibit maximum importance on the concrete slump value.
Abstract: Strontium hexaferrite (SrFe12O19; Sr-ferrite) is one of
the well-known materials for permanent magnets. In this study, Mtype
strontium ferrite was prepared by following the conventional
ceramic method from steelmaking by-product. Initial materials;
SrCO3 and by-product, were mixed together in the composition of
SrFe12O19 in different Sr/Fe ratios. The mixtures of these raw
materials were dry-milled for 6h. The blended powder was presintered
(i.e. calcination) at 1000°C for different times periods, then
cooled down to room temperature. These pre-sintered samples were
re-milled in a dry atmosphere for 1h and then fired at different
temperatures in atmospheric conditions, and cooled down to room
temperature. The produced magnetic powder has a dense hexagonal
grain shape structure. The calculated energy product values for the
produced samples ranged from 0.3 to 2.4 MGOe.