Abstract: Explosions may cause intensive damage to buildings
and sometimes lead to total and progressive destruction. Pressures
induced by explosions are one of the most destructive loads a
structure may experience. While designing structures for great
explosions may be expensive and impractical, engineers are looking
for methods for preventing destructions resulted from explosions. A
favorable structural system is a system which does not disrupt totally
due to local explosion, since such structures sustain less loss in
comparison with structural ones which really bear the load and
suddenly disrupt. Designing and establishing vital and necessary
installations in a way that it is resistant against direct hit of bomb and
rocket is not practical, economical, or expedient in many cases,
because the cost of construction and installation with such
specifications is several times more than the total cost of the related
equipment.
Abstract: A system for market identification (SMI) is presented.
The resulting representations are multivariable dynamic demand
models. The market specifics are analyzed. Appropriate models and
identification techniques are chosen. Multivariate static and dynamic
models are used to represent the market behavior. The steps of the
first stage of SMI, named data preprocessing, are mentioned. Next,
the second stage, which is the model estimation, is considered in more
details. Stepwise linear regression (SWR) is used to determine the
significant cross-effects and the orders of the model polynomials. The
estimates of the model parameters are obtained by a numerically stable
estimator. Real market data is used to analyze SMI performance.
The main conclusion is related to the applicability of multivariate
dynamic models for representation of market systems.
Abstract: Batch adsorption of recalcitrant melanoidin using the abundantly available coal fly ash was carried out. It had low specific surface area (SBET) of 1.7287 m2/g and pore volume of 0.002245 cm3/g while qualitative evaluation of the predominant phases in it was done by XRD analysis. Colour removal efficiency was found to be dependent on various factors studied. Maximum colour removal was achieved around pH 6, whereas increasing sorbent mass from 10g/L to 200 g/L enhanced colour reduction from 25% to 86% at 298 K. Spontaneity of the process was suggested by negative Gibbs free energy while positive values for enthalpy change showed endothermic nature of the process. Non-linear optimization of error functions resulted in Freundlich and Redlich-Peterson isotherms describing sorption equilibrium data best. The coal fly ash had maximum sorption capacity of 53 mg/g and could thus be used as a low cost adsorbent in melanoidin removal.
Abstract: Despite so many years- development, the mainstream of workflow solutions from IT industries has not made ad-hoc workflow-support easy or inexpensive in MIS. Moreover, most of academic approaches tend to make their resulted BPM (Business Process Management) more complex and clumsy since they used to necessitate modeling workflow. To cope well with various ad-hoc or casual requirements on workflows while still keeping things simple and inexpensive, the author puts forth first the TSM design pattern that can provide a flexible workflow control while minimizing demand of predefinitions and modeling workflow, which introduces a generic approach for building BPM in workflow-aware MISs (Management Information Systems) with low development and running expenses.
Abstract: Discrete choice model is the most used methodology for studying traveler-s mode choice and demand. However, to calibrate the discrete choice model needs to have plenty of questionnaire survey. In this study, an aggregative model is proposed. The historical data of passenger volumes for high speed rail and domestic civil aviation are employed to calibrate and validate the model. In this study, different models are compared so as to propose the best one. From the results, systematic equations forecast better than single equation do. Models with the external variable, which is oil price, are better than models based on closed system assumption.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: An implant elicits a biological response in the
surrounding tissue which determines the acceptance and long-term
function of the implant. Dental implants have become one of the
main therapy methods in clinic after teeth lose. A successful implant
is in contact with bone and soft tissue represent by fibroblasts. In our
study we focused on the interaction between six different chemically
and physically modified titanium implants (Tis-MALP, Tis-O, Tis-
OA, Tis-OPAAE, Tis-OZ, Tis-OPAE) with alveolar fibroblasts as
well as with five type of microorganisms (S. epidermis, S.mutans, S.
gordonii, S. intermedius, C.albicans). The analysis of microorganism
adhesion was determined by CFU (colony forming unite) and biofilm
formation. The presence of α3β1 and vinculin expression on alveolar
fibroblasts was demonstrated using phospho specific cell based
ELISA (PACE). Alveolar fibroblasts have the highest expression of
these proteins on Tis-OPAAE and Tis-OPAE. It corresponds with
results from bacterial adhesion and biofilm formation and it was
related to the lowest production of collagen I by alveolar fibroblasts
on Tis-OPAAE titanium disc.
Abstract: This paper proposes a hybrid method for eyes localization
in facial images. The novelty is in combining techniques
that utilise colour, edge and illumination cues to improve accuracy.
The method is based on the observation that eye regions have dark
colour, high density of edges and low illumination as compared
to other parts of face. The first step in the method is to extract
connected regions from facial images using colour, edge density and
illumination cues separately. Some of the regions are then removed
by applying rules that are based on the general geometry and shape
of eyes. The remaining connected regions obtained through these
three cues are then combined in a systematic way to enhance the
identification of the candidate regions for the eyes. The geometry
and shape based rules are then applied again to further remove the
false eye regions. The proposed method was tested using images from
the PICS facial images database. The proposed method has 93.7%
and 87% accuracies for initial blobs extraction and final eye detection
respectively.
Abstract: This article considers with the influence of selected economic indicators for the development of the Zlin region. Development of the region is mainly influenced by business entities which are located in the region, as well as investors who contribute to the development of regions. For the development of the region it is necessary for skilled workers remain in the region and not to leave these skilled workers. The above-mentioned and other factors are affecting the development of each region.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: The paper gives the pilot results of the project that is
oriented on the use of data mining techniques and knowledge
discoveries from production systems through them. They have been
used in the management of these systems. The simulation models of
manufacturing systems have been developed to obtain the necessary
data about production. The authors have developed the way of
storing data obtained from the simulation models in the data
warehouse. Data mining model has been created by using specific
methods and selected techniques for defined problems of production
system management. The new knowledge has been applied to
production management system. Gained knowledge has been tested
on simulation models of the production system. An important benefit
of the project has been proposal of the new methodology. This
methodology is focused on data mining from the databases that store
operational data about the production process.
Abstract: A framework to estimate the state of dynamically
varying environment where data are generated from heterogeneous
sources possessing partial knowledge about the environment is presented.
This is entirely derived within Dempster-Shafer and Evidence
Filtering frameworks. The belief about the current state is expressed
as belief and plausibility functions. An addition to Single Input
Single Output Evidence Filter, Multiple Input Single Output Evidence
Filtering approach is introduced. Variety of applications such as
situational estimation of an emergency environment can be developed
within the framework successfully. Fire propagation scenario is used
to justify the proposed framework, simulation results are presented.
Abstract: Process capability index Cpk is the most widely
used index in making managerial decisions since it provides bounds
on the process yield for normally distributed processes. However,
existent methods for assessing process performance which
constructed by statistical inference may unfortunately lead to fine
results, because uncertainties exist in most real-world applications.
Thus, this study adopts fuzzy inference to deal with testing of Cpk .
A brief score is obtained for assessing a supplier’s process instead of
a severe evaluation.
Abstract: In this paper , by using fixed point theorem , upper and lower solution-s method and monotone iterative technique , we prove the existence of maximum and minimum solutions of differential equations with delay , which improved and generalize the result of related paper.
Abstract: A mammography image is composed of low contrast area where the breast tissues and the breast abnormalities such as microcalcification can hardly be differentiated by the medical practitioner. This paper presents the application of active contour models (Snakes) for the segmentation of microcalcification in mammography images. Comparison on the microcalcifiation areas segmented by the Balloon Snake, Gradient Vector Flow (GVF) Snake, and Distance Snake is done against the true value of the microcalcification area. The true area value is the average microcalcification area in the original mammography image traced by the expert radiologists. From fifty images tested, the result obtained shows that the accuracy of the Balloon Snake, GVF Snake, and Distance Snake in segmenting boundaries of microcalcification are 96.01%, 95.74%, and 95.70% accuracy respectively. This implies that the Balloon Snake is a better segmentation method to locate the exact boundary of a microcalcification region.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.
Abstract: Recent advances in wireless sensor networks have led
to many routing methods designed for energy-efficiency in wireless
sensor networks. Despite that many routing methods have been
proposed in USN, a single routing method cannot be energy-efficient
if the environment of the ubiquitous sensor network varies. We present
the controlling network access to various hosts and the services they
offer, rather than on securing them one by one with a network security
model. When ubiquitous sensor networks are deployed in hostile
environments, an adversary may compromise some sensor nodes and
use them to inject false sensing reports. False reports can lead to not
only false alarms but also the depletion of limited energy resource in
battery powered networks. The interleaved hop-by-hop authentication
scheme detects such false reports through interleaved authentication.
This paper presents a LMDD (Low energy method for data delivery)
algorithm that provides energy-efficiency by dynamically changing
protocols installed at the sensor nodes. The algorithm changes
protocols based on the output of the fuzzy logic which is the fitness
level of the protocols for the environment.
Abstract: The objective of the present study was to determine
the effect of different concentration of spermatozoa and length of
storage in 5 0C on sperm motility. Semen was collected using
artificial vagina from goat aged 2 to 2.5 years. Fresh goat semen
with sperm motility ≥ 70% was used as material. Semen was
divided into 4 treatments of concentration (40 x 10 6 / ml, 50 x
106/ml, 60x106/ml, 70x106/ml) with length of storage 0,12,24,36 h. in
5 0C. There were interactions (P
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.